Instrukcja obsługi Sonance Visual Performance VP65 XT

Sonance głośnik Visual Performance VP65 XT

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Sonance Visual Performance VP65 XT (4 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/4

Introduction

Thank you for purchasing Sonance Visual Performance Series

Extreme Speakers. These weatherproof 6" speakers can provide

superior sound quality for high-humidity areas and are built to

survive temperature extremes from –30°F – +175°F (–34°C –

+79°C). Their shallow depth makes them easy to install in a vari-

ety of challenging spaces. Visual Performance Extreme speakers

provide excellent sound in yachts, saunas, steam rooms, and hot

tub areas.

This manual covers the following speaker models: VP65 XT

(rectangular), VP65R XT (round), VP65S XT (square), VP65R SST

XT (round, Single-Stereo Technology ®).

Box Contents

Sonance VP65 XT, VP65R XT, and VP65S XT speaker boxes contain

(2) speakers, (2) paint plugs (installed on the fronts of the

speakers), (2) paintable grilles and (1) mounting cutout

template.

Sonance VP65R SST XT speaker boxes contain (1) speaker,

(1) plastic paint plug (installed on the front of the speaker),

(1) paintable grille and (1) mounting cutout template.

Speaker Placement

St e r e o Sp eake r P la ce me nt ( VP 65 X T)

• Place the left and right speakers on the same wall, from 6 to

10 feet (1.8 – 3m) apart.

• If the listeners will be seated the speakers should be located

38 – 42 (97 – 107cm) inches from the floor.

• If listeners will be standing the speakers should be located

5 feet (1.5m) from the floor.

• The ideal listening distance will be between 4 and 10 feet (1.2

and 3m) away from the speakers. The best stereo performance

will be midway between the speakers.

Use Figure 1 (next column) as a guide

D i st r i bu te d A ud i o P la c em en t

(V P 6 5 R X T/ V P 6 5S X T/ V P 6 5R SS T X T)

Sonance VP65R XT, VP 65S XT and VP65R SST XT in-ceiling

speaker models provide excellent coverage in distributed

audio systems from a wide variety of installation locations.

The table and illustration in show how far apart Figure 2

speakers can be placed at various ceiling heights while still

providing good coverage for all listeners.

The VP65R SST XT reproduces both stereo channels from a single

location, making it ideal for use in bathrooms, saunas, or in any

location where a pair of stereo speakers would be impractical.

Before Installation: Retrofit

1. Determine the location for the speaker (see Speaker

Placement on page 1).

2. Perform an obstruction survey to be certain that there are

no studs, conduit, pipes, heating ducts, pocket doors or

air returns in the wall cavity that will interfere with the

speaker.

I N S T R U C T I O N M A N U A L

V I S UA L P E R F O R M A N C E ® S E R I E S

E X T R E M E S P E A K E R S

S W :A F E T Y A R N I N G

T F MHESE SPEAKERS HAVE AST OUNT®TABS THAT PREVENT THE

SPEAKER FROM FALLING OUT OF THE MOUNTING HOLE DURING THE

INSTALLATION PROCESS.

T F MH E E D G E S O F T H E A S T O U N T T A B S A R E V E R Y S H A R P.

US E C A U T I O N W H E N H A N D L I N G T H E S P E A K E R .

C OVERAGE

AREA COVERAGE

AREA

S PEAKER

SPACING

S )PEAKER S (PACING IN FEET

FOR ISTRIBUTED UDIO YSTEM A D A S

STANDING LISTENER SEATED LISTENER

10-

FOOT CEILING

12-

FOOT CEILING

14-

FOOT CEILING

F 9.5’ (2.9m) ApartOOT CEILING

13.5’ (4.1m) Apart

17.5’ (5.3m) Apart

21.5’ (6.6m) Apart

5.7’ (1.7m) Apart

9.7’ (3.0m) Apart

13.7’ (4.2m) Apart

17.7’ (5.4m) Apart

F A S SIGURE 2: DISTRIBUTED UDIO PEAKER PACING

38” – 42”

(97cm – 107cm)

(Seated Listeners)

5‘ (1.5m)

(Standing Listeners)

6‘ – 10’ (1.8m – 3m)

Apart

F S PIGURE 1: STEREO PEAKER LACEMENT

SONANCE VISUAL PERFORMANCE®EXTREME SPEAKERS

3. VP Extreme speakers require the following mounting cutouts:

• VP65 XT: 615

/16” (176mm) wide by 10¾” (273mm) high, with

at least 2½” (64mm) of depth within the mounting cavity.

• VP65R XT: 8¼” (210mm) diameter, with at least 3½”

(89mm) of depth within the mounting cavity.

• VP65S XT: 8¼” (210mm) wide by 8¼” (210mm) high, with at

least 3½” (89mm) of depth within the mounting cavity.

• VP65R SST XT: 8¼” (210mm) diameter, with at least 3½”

(89mm) of depth within the mounting cavity.

4. Position the included mounting cutout template where the

speaker is to be located and pencil an outline on the wall

or ceiling.

• If you are unsure about obstructions, drill a small hole in

the center of the outline and insert a coat hanger wire into

the hole to feel-around for possible obstructions.

5. Cut the mounting hole using tools appropriate for the

construction, and run the speaker wires from the mounting

hole to the amplifier location.

• Consult local building codes before running speaker wires

through walls.

Installation

Sonance VIsual Performance Series Extreme speakers feature

exclusive FastMount®tabs and an integral RotoLock®mounting

system for quick mounting directly into existing walls and ceilings.

WA R N I N G : T HE E D G E S O F T H E FA S T M O U N T TA B S

A R E V E R Y S HA R P. U S E C A U T ION W H E N H A N-

D L I N G T H E S P E A K E R .

1. Remove the paint plug from the speaker.

2. Strip ¼” – ½” (6mm – 13mm) of insulation from each

speaker lead. Twist the strands or tin the exposed wire

with solder to ensure that there are no stray strands.

(Stray strands that touch each other can cause a short-

circuit that can damage the amplifier.)

3. The speaker’s connector posts are spring-loaded. Push the top

of each connector post down to open the connector and insert

the exposed wires into the holes in the posts (see Figure 3).

• The speaker’s positive post is labeled with a red dot; the

negative post is labeled with a black dot.

• The VP65R SST XT has two sets of connection terminals,

located on opposite sides of the crossover board.

• After making all connections, double-check that you

connected amplifier “+” to speaker “+” and amplifier “–”

to speaker “–”.

4. As shipped, the RotoLock clamps can accommodate a max-

imum wall or ceiling material thickness of 1¼” (32mm).

NOTE: IF YOU’RE INSTALLING THE VP65R XT, VP65S XT, OR

VP65R SST XT INTO CEILING MATERIAL THAT IS THICKER THAN

1¼” (32MM YOU CAN REMOVE THE FEET OF THE OCK), ‘ ’ ROTOL

CLAMPS, WHICH WILL ALLOW YOU TO CLAMP THE SPEAKER TO CEIL-

ING MATERIAL THAT IS UP TO MM THICK1¾” (44 ) . TO REMOVE THE

CLAMP FEET

, USE A SMALL SCREWDRIVER TO GENTLY RELEASE THE

LO CKING LEVERS (F 4IGUR E , LEFT). THEN REMO VE THE FEET FROM

THE CLAMPS (F 4IGUR E , ).RIGHT

5. Make sure all the RotoLock clamps are retracted so that they

are tucked within the mounting hole’s border. Insert the

speaker into the mounting hole ( , left). TheFigure 5

FastMount tabs will prevent the speaker from falling out of

the mounting hole, allowing you to let go of the speaker to

pick-up tools or other items ( , right).Figure 5

NOTE: THE AST OUNT TABS ARE DESIGNED FOR ONE TIME USEF M -

ONLY. IF THE SPEAKER IS REMO VED FROM THE MO UNTING HOLE THE

F MAST OUNT TABS WILL DISCONNECT AND REMAIN INSIDE THE WALL

OR CEILING.

6. Tighten the four screws on the front of the speaker baffle. The

RotoLock clamps will automatically rotate into position and

begin clamping the speaker ( , page 3).Figure 6

FastMount

Tabs

RotoLock Clamps

(retracted)

F SIGURE 5: INSERTING THE PEAKER INTO THE OUNTING OLEM HF TIGURE 3 CONNECTION ERMINALS

Connection Terminals

(1 Set on VP65R XT, VP65S XT, VP65 XT;

2 Sets on VP65R SST XT)

FastMount

Tabs

Locking Lever

Remove Foot

F R LIGURE 4: REMOVING THE OTO OCK LAMP EETC F

SONANCE VISUAL PERFORMANCE®EXTREME SPEAKERS

• When you notice resistance on the screws the speaker has

been clamped successfully.

IM P O RTAN T : A L WAY S U SE L O W T O R Q U E S E T T I N G S- ;

NEVER O V E R -T I G H T E N .

N R LOT E : AD J US TI N G TH E T EN SI O N O F T HE OTO O C K C L AM PS S O

THAT T HE SPEA KER FRAME IS F LAT WIL L HEL P EN SU RE THAT T HE GRI LL E

C O N TA C TS T HE W A LL A L L T H E W AY A RO U ND T HE S PEA KE R F O R A

P RO P ER F IT.

7. The new micro-trim grille is held in place by several small,

powerful magnets on the rear of the grille. Place the grille

against the speaker and the magnets will hold it firmly in

place. When the grille is properly installed, the grille trim

should make contact with the mounting surface all the way

around the speaker.

Painting the Grilles

See the accompanying instruction sheet for painting instructions.

Environmental Specifications

Maximum Heat: +175°F (+79°C)

Maximum Cold: –30°F (–34°C)

Maximum Humidity: 99% (120°F/49°C)

95% (–30°F/–34°C)

These speakers meet or exceed the foll owing:

Salt Spray: ASTM-B117

UV Test: ASTM-G23H

IEC/CEE

Water Splashing Test: IP-X4

Vibration Test: ASTM D5112-98 and ASTM D3580-95

Performance Specifications

V P 6 5 X T

Tweeter: 1" (25mm) polyurethane dome

Woofer: 6½" (165mm) injection-molded

polypropylene/graphite cone, with

integral Santoprene ®surround

Frequency Response: 55Hz – 20kHz ±3dB

Impedance: 8 ohms nominal; 6 ohms minimum

Power Handling: 5 watts minimum; 130 watts maximum

Sensitivity: 89dB SPL (2.83V/1 meter)

Grille Material: Powder-coated stainless steel

Dimensions (W x H x D): 83/8" x 12¼" x 2½”

(213mm x 311mm x 64mm)

Cutout Dimensions (W x H): 615

/16” x 10¾" (176mm x 273mm)

Shipping Weight: 12 lbs (5.4kg) pair

V P 6 5 R X T

Tweeter: 1" (25mm) polyurethane dome

Woofer: 6½" (165mm) injection-molded

polypropylene/graphite cone, with

integral Santoprene ®surround

Frequency Response: 55Hz – 20kHz ±3dB

Impedance: 8 ohms nominal; 6 ohms minimum

Power Handling: 5 watts minimum; 130 watts maximum

Sensitivity: 89dB SPL (2.83V/1 meter)

Grille Material: Powder-coated stainless steel

Dimensions (Dia x D): 9¾” x 3½” (248mm x 89mm)

Cutout Dimensions (Dia): 8¼” (210mm)

Shipping Weight: 12 lbs (5.4kg) pair

V P 6 5 S X T

Tweeter: 1" (25mm) polyurethane dome

Woofer: 6½" (165mm) injection-molded

polypropylene/graphite cone, with

integral Santoprene surround

Frequency Response: 55Hz – 20kHz ±3dB

Impedance: 8 ohms nominal; 6 ohms minimum

Power Handling: 5 watts minimum; 130 watts maximum

Sensitivity: 89dB (SPL 2.83V/1 meter)

Grille Material: Powder-coated stainless steel

Dimensions (H x W x D): 97/8" x 97/

8” x 3½"

(251mm x 251mm x 89mm)

Cutout Dim. (W x H): 8¼" x 8¼" (210mm x 210mm)

Shipping Weight: 12 lbs. (5.4kg) pair

V P 6 5 R S S T X T

Tweeter: Two 1" (25mm) polyurethane domes

Woofer: 6½" (165mm) injection-molded

polypropylene/graphite cone, with

integral Santoprene ®surround, dual

voice coil

Frequency Response: 55Hz – 20kHz ±3dB

Impedance: 8 ohms nominal; 6 ohms minimum

Power Handling: 5 watts minimum; 130 watts maximum

Sensitivity: 89dB SPL (2.83V/1 meter)

Grille Material: Powder-coated stainless steel

Dimensions (Dia x D): 9¾” x 5 3

/16” (248mm x 132mm)

Cutout Dimensions (Dia): 8¼” (210mm)

Shipping Weight: 4.5 lbs (2.1kg) each

RotoLock

Screws

F R LIGURE 6: TIGHTENING THE OTO OCK CREWSS

Specyfikacje produktu

Marka:	Sonance
Kategoria:	głośnik
Model:	Visual Performance VP65 XT

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Sonance Visual Performance VP65 XT, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje głośnik Sonance

Sonance Visual Performance Extreme VPXT8R Instrukcja

8 Stycznia 2025

Sonance Visual Performance VP38R Instrukcja

8 Stycznia 2025

Sonance MAG5.1R Instrukcja

8 Stycznia 2025

Sonance MAG6R Instrukcja

8 Stycznia 2025

Sonance Mariner MX52 Instrukcja

1 Stycznia 2025

Sonance Mariner MX66 Instrukcja

9 Października 2024

Sonance Garden SGS Subwoofer Instrukcja

13 Września 2024

Sonance IS4 Instrukcja

10 Września 2024

Sonance Mariner 64 Instrukcja

29 Sierpnia 2024

Sonance Mariner 64 SST Instrukcja

27 Sierpnia 2024

Instrukcje głośnik

Najnowsze instrukcje dla głośnik

Bowers & Wilkins LCR3 Instrukcja

15 Stycznia 2025

Hifonics Vulcan VX6.2E Instrukcja

15 Stycznia 2025

Pyle PLRGSW64BK Instrukcja

15 Stycznia 2025

ION Insta Sound Instrukcja

15 Stycznia 2025

Pure Acoustics QBT-340 Instrukcja

15 Stycznia 2025

Yamaha WX-010 Instrukcja

15 Stycznia 2025

Polk REACT SOUND BAR 1 Instrukcja

15 Stycznia 2025

Sennheiser AMBEO Soundbar Plus SB02M Instrukcja

15 Stycznia 2025

Klipsch Reference RB-25 Instrukcja

15 Stycznia 2025

Klipsch Reference RB-35 Instrukcja

15 Stycznia 2025