Instrukcja obsługi Sonance Visual Performance VP38R

Sonance głośnik Visual Performance VP38R

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Sonance Visual Performance VP38R (4 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/4

Introduction

Thank you for purchasing the Sonance Visual Performance VP38R Speakers.

When properly installed your new speakers will give you years of

entertainment pleasure.

Box Contents

Visual Performance in-ceiling speaker box contains:

(1) Visual Performance speaker

(1) Paintable grille

(1) Mounting cutout template

Speaker Placement - Spacing

The VP38R speakers have very wide dispersion due to the small diameter of

the woofer and tweeter used in the speaker.

This wide dispersion allows the speakers to be placed from 6'-10' (1.8-3.0

meters) apart center to center in a typical 8'-9' (2.5-2.7 meter) height ceiling.

As the ceiling height increases it is possible to separate the speakers farther

following the chart below.

6-10 Feet (1.8-3m)

Speaker Placement - Examples

Kitchen

KitchenKitchen

The kitchen floorplan below illustrates an ideal installation of a four

VP38R satellite and one BPS6 subwoofer system.

In this floorplan we have placed the satellites in the high traffic areas and

the subwoofer over the island.

Dining Room

Dining RoomDining Room

In the floorplan above we have shown a typical dining room with six

VP38R satellites and two BPS6 subwoofers.

Please note the location of the subwoofers at the center of the array of

VP38R speakers. Keeping the subwoofers in close proximity to the

satellites will allow a seamless transition from satellite to subwoofer.

Note the alternating left and right speakers for maximum sound field

creation.

Left Right

LeftRight

Left Right Left

Right Left Right

6-10 Feet (1.8-3m)

6-10 Feet (1.8-3m) 6-10 Feet (1.8-3m)

SubSub

Sub

When placed as shown in the examples below the VP38R speaker will

provide even coverage over a large area.

Speaker Placement Sound field–

To maximize the sound field created by the VP38R system we suggest

connecting the speakers using an alternating left / right pattern as shown

in the floorplan to the right.

Using this connection method is very important in rooms without a

defined listening position or where multiple people will listen at the same

time.

With the speakers connected this way no matter where you are in the

room you are more likely to hear a true stereo signal.

1. Determine the location for the speaker (see Speaker Placement on

page 1).

2. Perform an obstruction survey using a stud finder to be certain that

there are no studs, conduit, pipes, heating, ducts, pocket doors or

air returns in the ceiling cavity that will interfere with the speaker. If

you are unsure about obstructions, drill a small hole in the center of

the outline and insert a coat hanger wire into the hole to feel

around for possible obstructions.

3. Cut the mounting hole using a 4" (102mm) hole saw, and run the

speaker wires from the mounting hole to the amplifier location.

NOTE: CONSULT LOCAL BUILDING CODES BEFORE RUNNING

SPEAKER WIRES THROUGH CEILINGS.

4. The high pass filter switch is located on the back of the speaker. The

setting for this switch should be determined before you start

installing the VP38R speaker.

5. The default position is ON. In the

ON position the high pass

filter will limit the quantity of

low bass sent to the VP38R

speaker. The high pass filter

is necessary to allow a smooth

transition from the VP38R to the

BPS6 subwoofer.

6. If the VP38R will be used without

a subwoofer the high pass filter

switch should be set in the OFF

position.

7. If the VP38R will be used with a

Sonance DSP series amplifier the

high pass filter switch should be

set in the OFF position. The high

pass filter will be applied in the

DSP preset.

Sonance Visual Performance Speakers feature integral two piece Roto-

Lock mounting system for quick mounting directly into existing ceilings.

8. The Roto-Lock system can accommodate a ceiling material thickness

of 1/4" (6mm) to 1-7/8 (48mm). ”

With the toggle foot cap removed the system can accommodate a

ceiling material thickness of 7/16" (12mm) to 2-1/8 (54mm).”

VISUAL PERFORMANCE VP38R

9. When installing into double

drywall or other thicker ceiling

materials, you may need to

remove part of the two-piece

toggle feet. Unscrew the

toggle foot cap from the

toggle foot.

In a system with four VP38R satellites and one BPS6 subwoofer all

speakers can be connected to a two channel amplifier.

This connection is possible using the high pass filter on the VP38R

satellite and the built in crossover in the BPS6 subwoofer.

The alternative connection method is to dedicate two amplifier channels

to the four VP38R satellites then connect the BPS6 subwoofer to a

dedicated pair of amplifier channels.

Using this connection method allows you to adjust the level of the

satellites and subwoofers independently.

When wiring a DOS system (VP38R & BPS6) you have two options for

connecting the speakers to the amplifier.

VISUAL PERFORMANCE VP38R

1. The VPSQ Square Adapter slides on through

the rear of the round speaker prior to

installation.

2. Place speaker through the round ceiling cut-

out, loosely tighten the Roto-Lock toggle feet,

then align the Square Adapter on the speaker

to the correct symmetry.

3. Once the Square Adapter is straight in line

with other speakers, lighting, and/or HVAC

ceiling fixtures, secure the Roto-Lock toggle

feet at a low torque setting

4. Attach the magnetic grille.

NOTE: The Square Adapter includes small screw

holes that can be used to tighten the adapter to

keep the corners flush to the ceiling in case of

heavy textures.

Note: #6 drywall screws and drywall anchors not

included. Screws will not always be necessary for

every installation.

10. Strip 1/4 1/2 (6mm 12mm) of insulation from each speaker ” – ” –

lead. Twist the strands or tin the exposed wire with solder to ensure

that there are no stray strands.

I M P O R T A N T: ALWAYS USE LOW TORQUE SETTINGS; DO

NOT OVER TIGHTEN!

NOTE: Adjust the tension of the Roto-Lock clamps so that the speaker frame

is flat. This will help ensure the grille contacts the ceiling all the way around

the speaker for a proper fit.

12. Make sure all the Roto-Lock

toggle feet are retracted so that

they are tucked within the

mounting hole’s border.

13. Insert the speaker into the hole in

the ceiling.

14. Tighten the screws on the front of

the speaker baffle. The Roto-Lock

toggle feet will automatically

rotate into position and begin

clamping the speaker. When you

notice resistance on the screws the

speaker has been clamped

successfully.

NOTE: Stray strands that

touch each other can cause a

short-circuit that can damage

the amplifier!

11. -loaded. Push the top of each The speaker’s terminals are spring

terminal down to open the connector and insert the exposed wires

into the holes in the spring terminals. spring The speaker’s positive

terminal is labeled with a red dot; the negative spring terminal is

labeled with a black dot. Double check that you connected

amplifier “ ” to speaker “ ” and amplifier “–” to speaker “–”+ + .

Roto-Lock Screws

Roto-Lock ScrewsRoto-Lock Screws

Roto-Lock Clamps

Roto-Lock ClampsRoto-Lock Clamps

(retracted)

(retracted)(retracted)

15. The micro-trim grille is held in place by several small, powerful

magnets on the speaker frame. Place the grille against the speaker

and the magnets will hold it firmly in place. When properly

installed, the grille trim should make contact with the wall all the

way around the speaker.

Specyfikacje produktu

Marka:	Sonance
Kategoria:	głośnik
Model:	Visual Performance VP38R

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Sonance Visual Performance VP38R, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje głośnik Sonance

Sonance Visual Performance Extreme VPXT8R Instrukcja

8 Stycznia 2025

Sonance Visual Performance VP38R Instrukcja

8 Stycznia 2025

Sonance MAG5.1R Instrukcja

8 Stycznia 2025

Sonance MAG6R Instrukcja

8 Stycznia 2025

Sonance Mariner MX52 Instrukcja

1 Stycznia 2025

Sonance Mariner MX66 Instrukcja

9 Października 2024

Sonance Garden SGS Subwoofer Instrukcja

13 Września 2024

Sonance IS4 Instrukcja

10 Września 2024

Sonance Mariner 64 Instrukcja

29 Sierpnia 2024

Sonance Mariner 64 SST Instrukcja

27 Sierpnia 2024

Instrukcje głośnik

Najnowsze instrukcje dla głośnik

Yamaha CMA3SW Instrukcja

9 Stycznia 2025

Yamaha IF2112/64 Instrukcja

9 Stycznia 2025

Yamaha IF2115/99 Instrukcja

9 Stycznia 2025

Yamaha VXC2FB Instrukcja

9 Stycznia 2025

Yamaha VXC6W Instrukcja

9 Stycznia 2025

Yamaha VXC2P Instrukcja

9 Stycznia 2025

Yamaha VXC8-VA Instrukcja

9 Stycznia 2025

Yamaha VC6NB Instrukcja

9 Stycznia 2025

Yamaha IS1218 Instrukcja

9 Stycznia 2025

Phoenix Gold ZDSKFO2 Instrukcja

9 Stycznia 2025