Instrukcja obsługi SolidDrive MSK-1-T

SolidDrive Nie skategoryzowane MSK-1-T

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla SolidDrive MSK-1-T (2 stron) w kategorii Nie skategoryzowane. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
WARRANTY
WARNING
SolidDrive MSK-1-T/MSK-1SM-T/MSK-1G-T Specications
Type
Construction
Dimensions
Weight
SolidDrive MSK-1-T In-Wall and In-Ceiling
(Required for Drywall Mounting) Mounting Bracket Specications
NOTE: When installed in Canada, this product must be installed in accordance with the
Canadian Electrical Code, C22.1, Part1.
Type
Frequency Response(Hz)
Recommended Amplier Power
MSK-1-T & MSK-1sm-T Dimensions
MSK-1g-T Dimensions
Weight
UL Listing
Full Range Transducer
70 Hz to 15 kHz
10 Watts
2.28'' Diameter x 4.8'' Height
Mounting Foot 3.5'' Diameter
2.28'' Diameter x 4.8'' Height
Mounting Foot 2.0'' Diameter
1.5 lb / .68 kg
1480 & 2043 Pending
Patented balanced cantilever spring bracket
Heavy duty, galvanized steel
12OC – 2.0'' H x 17.5'' W x 5.0'' D
16OC – 2.0'' H x 25.5'' W x 5.0'' D
24OC – 2.0'' H x 13.5'' W x 5.0'' D
1.0 lb / .45 kg
218-2127-T REV-08.14.17
SolidDrives are guaranteed for 7 years from date of purchase. Any misuses or modi-
cations to this equipment in any way will void the warranty.
Read instructions prior to operating. To reduce the risk of re or electric shock, do not
expose this product to rain or moisture. Unplug prior to cleaning and clean with a damp
cloth. There are no user-serviceable parts in this product, please refer all servicing to
qualied personnel.
INSTALLATION & USE GUIDE
for MSK-1-T, MSK-1sm-T & MSK-1g-T
Sound Masking Transducer
INSTALLATION OF SOLIDDRIVE MSK-1-T INTO WALLS AND CEILINGS
GETTING STARTED WITH SOLIDDRIVE
Experience Audio Perfection
Induction Dynamics extensive line of audio products makes it easy to create the
ultimate audio system, regardless of installation requirements. Induction Dynamics
builds these products with only the most select components and materials; and
utilizes numerous unique and proven technologies.
By utilizing these basic installation steps, you can install the SolidDrive MSK-1-T into walls
and ceilings for a variety of sound masking applications.
What’s included with the SolidDrive MSK-1-T for installation into walls and ceilings and
what is supplied by the installer —
A SolidDrive MSK-1-T consists of: One (1) SolidDrive MSK-1-T unit with included 10W
transformer, supplied with 4 hard wire leads and one duplex conduit connector. *Additional
mounting materials may need to be ordered with the SolidDrive MSK-1-T or supplied by the
installer depending on the application.
For drywall: For in-wall and in-ceiling installation, you will have ordered one (1) or more
SolidDrive MSK-1-T’s and one (1) or more patented acoustic in-wall mounting brackets (one
(1) bracket per MSK-1-T), which comes with four (4) #8-32 x 5/16'' Phillips at head machine
screws for mounting the drive to the bracket. At the time of the order, you will also have
specied mounting bracket(s) in widths of 12OC, 16OC, or 24OC (ON CENTER of wall studs or
ceiling joists) for proper width. *Installation also requires four (4) 1 3/8'' drywall screws and
one (1) container of 3M
® Super 77 Spray Adhesive (supplied by the installer).
EXISTING DRYWALL INSTALLATION NOTE:
For retrotting the SolidDrive MSK-1-T into existing drywall installations, it will be necessary
to remove a portion of the existing drywall before installation and to replace the drywall after
the SolidDrive MSK-1-T is installed. Please refer to the instructions marked with EXISTING
DRYWALL for the steps necessary for the type of installation. If installing the SolidDrive
MSK-1-T in new construction, IGNORE the EXISTING DRYWALL steps.
STEP 1
INSTALLATION INTO EXISTING DRYWALL
For installing the SolidDrive mounting bracket into existing drywall, rst cut a MSK-1-T
rectangular opening in the drywall. The minimum recommended opening size is approximately
fteen inches tall and beyond the width of the adjacent wall studs. This will help in attaching
the mounting bracket, feathering the drywall back in, and getting the drywall to meet at the
seams (Figure 1). This will allow proper distribution of sound and the SolidDrive MSK-1-T will
function with optimum performance.
Figure 1
Cut an opening
large enough
to install the
mounting
bracket to the
wall studs
STEP2
Attach the SolidDrive mounting bracket to wall studs or ceiling joists
Place the mounting bracket between the wall studs or ceiling joists and secure with four 1 3/8"
drywall screws. Insert the screws through the four pre-drilled holes in each ange and screw
them into the face of each wall stud or ceiling joist (Figure 2). The drywall screws need to be
driven ush with the surface of the ange so that the drywall sets ush on the bracket ange.
MSE Audio / 8005 W 110th St / Suite 208 / Overland Park, KS 66102 / 855.663.5600 / 913.663.5600 / www.soliddrive.com
Figure 2
SolidDrive
MSK-1-T
mounting
bracket
attached to
the wall studs
STEP7
Install the new drywall
Immediately install the new drywall before the spray adhesive sets up (approximately 10
minutes). This allows adjustment of the panel before the nal location is determined. The
drywall panel is to be tted to the wall studs or ceiling joists and screwed into position.
Apply joint compound in the space between the drywall panels and proceed with the
normal taping, sanding and nishing routine. The joint compound lled between the
panels will improve the distribution of sound as well as overall sound quality.
By utilizing these basic installation steps, you can install the SolidDrive MSK-1sm-T on
wood, laminate, composites, and other porous surfaces. The MSK-1sm-T is commonly
used on desks, conference tables, cabinetry, and other furniture.
INSTALLATION OF SOLIDDRIVE MSK-1sm-T TO WOOD SURFACES
Figure 1
Mounting the
SolidDrive
MSK-1sm-T to
a table.
Once you have determined where to mount the SolidDrive MSK-1sm-T, spray a thin layer
of 3M® Super 77 adhesive on the bottom of the SolidDrive, then use the appropriate length
wood screws to attach it securely to the surface. The adhesive improves the sonic
transmission between the drive and the surface. The best mounting location is typically
out of sight on the underside or back of desks, counter tops, conference tables, or other
ofce/home furniture. The four pre-drilled mounting holes on the SolidDrive MSK-1sm-T
oversized mounting base will hold screws as large as #9.
Some installations may require that pilot holes be drilled into the surface material due to
its hardness, especially if larger, coarse thread screws are used.
For installation on glass surfaces, the SolidDrive MSK-1g-T comes with a VHB
double-sided adhesive disc.
INSTALLATION OF SOLIDDRIVE MSK-1g-T TO GLASS SURFACES
STEP5
Apply adhesive to the drywall surface and base of the SolidDrive
If possible, position the drywall panel so that the SolidDrive MSK-1-T is at the center of the
panel or as far from the edge of the panel as possible. This will allow proper distribution of
sound and the SolidDrive MSK-1-T will function with optimum performance. Prior to
mounting, take measurements of the new drywall panel to determine the exact area that
will come in contact with the base of the SolidDrive MSK-1-T and spray that area liberally
with the 3M® Super 77 contact spray adhesive. Also, liberally spray the surface of the
oversized mounting base of the SolidDrive MSK-1-T (masking around the base is highly
recommended to prevent overspray). NOTE: Failure to apply the adhesive to both the
drywall surface and oversized mounting base will prevent the system from functioning
properly.
STEP4
Electrical connections
Make the electrical connection between the
SolidDrive MSK-1-T and the speaker cable using
the desired transformer setting. NOTE: When
installed in Canada, this product must be installed
in accordance with the Canadian Electrical Code,
C22.1, Part1.
Black-
Red-
Yellow-
Blue-
10W: 5 wire input
10 W
COM
10 W
5 W
2.5 W
Figure 4 Transformer connections
AMP SolidDrive SolidDrive SolidDrive
Connecting Multiple SolidDrives
Connect the amplier (–) terminal to all Black (COM) wires for all SolidDrives in the system.
Connect the amplier (+) terminal to the colored wire that corresponds to the desired
power tap for each SolidDrive in the system. Trim off the exposed bare wire on all unused
wires and ensure that they cannot short to each other. Failure to do so may result in
misoperation and place an unexpected load on the amplier.
STEP3
Insert the SolidDrive into the bracket
Feed the SolidDrive MSK-1-T cable through the round opening in the face of the mounting
bracket. Insert the SolidDrive MSK-1-T through the same opening with the oversized
mounting base facing outward toward the side that the drywall will be installed and ush
against the bracket face. Align the pre-drilled holes in the mounting base to the threaded
holes in the bracket face (Figure 3). Attach the SolidDrive MSK-1-T securely to the mounting
bracket using the 4 Phillips at head machine screws.
Figure 3
SolidDrive
MSK-1-T
being installed
into the
mounting
bracket
The SolidDrive MSK-1g-T should be mounted in an inconspicuous location of the window.
Simply apply the VHB pad that comes with the drive to the base of the drive (the side
opposite the label). Remove one side of the protective layers from the VHB disc and apply
to the base of the MSK-1g-T. Then remove the other protective layer and apply to glass
surface with moderate pressure.
When mounting the SolidDrive on the window, keep it about 4 to 6 inches from the window
frame. The SolidDrive MSK-1g-T will have maximum output with at least 20 square feet of
window surface space.
Figure 1
Mounting the
SolidDrive
MSK-1g-T to
glass.
STEP6
EXISTING DRYWALL
Re-install rectangular cutout in wall
For re-installing the rectangle drywall panel that was cut out to install the SolidDrive
MSK-1-T, it is important to create a uniform seal between the cut drywall and the existing
drywall. This will allow proper distribution of sound and the SolidDrive will MSK-1-T
function with optimum performance. Apply fast setting joint compound, not vinyl based, in
the space between the cutout section and the existing drywall panel. Make sure to ll the
space completely with drywall compound then proceed with the normal taping, sanding
and nishing routine.

Specyfikacje produktu

Marka: SolidDrive
Kategoria: Nie skategoryzowane
Model: MSK-1-T

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z SolidDrive MSK-1-T, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Nie skategoryzowane SolidDrive

SolidDrive

SolidDrive MSK-1 Instrukcja

4 Lutego 2025
SolidDrive

SolidDrive MSK-1G Instrukcja

4 Lutego 2025
SolidDrive

SolidDrive MSK-1-T Instrukcja

4 Lutego 2025
SolidDrive

SolidDrive MSK-1SM Instrukcja

4 Lutego 2025

Instrukcje Nie skategoryzowane

Najnowsze instrukcje dla Nie skategoryzowane

AirLive

AirLive POE-GSH402-BT Instrukcja

25 Marca 2025
ETON

ETON UG VW T5 F3.2 Instrukcja

25 Marca 2025
Ikan

Ikan PT4500S-TMW Instrukcja

25 Marca 2025
WEG

WEG MPW18-3-D004 Instrukcja

25 Marca 2025
Vello

Vello HGS-2 Instrukcja

24 Marca 2025
Genexis

Genexis FiberBox XGS2120 Instrukcja

24 Marca 2025
Autel

Autel MaxiSys Ultra S2 Instrukcja

24 Marca 2025
Thermador

Thermador VTN2DA Instrukcja

24 Marca 2025
Kanto

Kanto CM-EXT60 Instrukcja

24 Marca 2025
Silver Cross

Silver Cross Geneva Wardrobe Instrukcja

24 Marca 2025