Instrukcja obsługi Snom D8C
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Snom D8C (2 stron) w kategorii Nie skategoryzowane. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/2

ENGLISH
Copyright, Trademarks, Legal Disclaimers
© 2024 Snom Technology GmbH. All Rights Reserved.
Snom, the names of Snom products, and Snom logos are trademarks owned by
Snom Technology GmbH.
All product specications are subject to change without notication. Snom
Technology GmbH reserves the right to revise and change this document at any
time, without being obliged to announce such revisions or changes beforehand
or after the fact.
Although due care has been taken in the compilation and presentation
of the information in this document, the data upon which it is based may
have changed in the meantime. Snom therefore disclaims all warranties
and liability for the accurateness, completeness, and currentness of the
information published, except in the case of intention or gross negligence on
the part of Snom or where liability arises due to binding legal provisions.
Important Information
Please read the instructions on safety and disposal and on how to set up and use
the device before using it and also give them to other users to read or inform
those users of their contents.
The nameplate is located at the bottom or rear of the product.
Safety Instructions
Follow the instructions in this guide and other applicable documentation of the
device.
• For professional use with Snom D8xx phones only. Do not connect to PC or
to other phones!
• Mount the device only at heights not exceeding 2m.
• Avoid placing the cables where people may trip over them or where they may
be exposed to mechanical pressure as this may damage them.
• This device is for indoor use only. NOT FOR OUTDOOR USE!
• Do not install the device in rooms with high humidity (like bathrooms, laundry
rooms, damp basements, etc.). Do not immerse the device in water and do not
spill or pour liquids of any kind onto or into the device.
• Do not install the device in surroundings at risk for explosions (paint shops,
for example). Do not use the device if you smell gas or other potentially
explosive fumes.
• Do not use the device during thunderstorms. Lightning striking the power
grid may cause electric shocks.
• To deactivate the device, remove the USB cable and/or the power adapter.
Standards conformance
This device complies with the essential health, safety, and
environmental requirements of all relevant European directives and
UK legislation. This device meets the relevant US and Canadian health,
safety, and environmental standards.
The declaration of conformity can downloaded at www.snom.com/conformity.
Unauthorized opening, changing, or modifying the device will cause the warranty
to lapse and may also result in the loss of CE, FCC, and IC conformity. In case of
malfunction contact authorized service personnel, your seller, or Snom.
• SELV (Safety Extra Low Voltage) Compliance: Safety status of Input/Output
connections comply with SELV requirements.
• Safety: IEC 62368-1
• Connectors:
◦1 USB standard type A plug
◦1 USB standard type A port
◦1 5V DC power jack
• Power.
Provided by the phone via the USB connector. A power adapter (available
separately) is needed which also supplies power to for the second module
the third module via USB cable. The third module may also need a power
adapter if a USB device is connected to its USB port.
Mass Power, model NBS12E050200UV, Snom PN 00004570
◦EU/UK: shipped with EU and UK clips
◦U.S./Canada: shipped with U.S. clip
IMPORTANT ADDITIONAL INFORMATION USA
FCC part 15
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at the user’s expense.
WARNING: Changes or modications to this equipment not expressly approved (Bitte Blatt umdrehen, weiter auf der Rückseite)
by the party responsible for compliance could void the user’s authority to
operate the equipment.
IMPORTANT ADDITIONAL INFORMATION Industry Canada
This Class A digital apparatus complies with Canadian requirements: CAN
ICES-3 (A)/NMB-3(A).
This product meets the applicable Innovation, Science and Economic
Development Canada technical specications.
Cet appareil numérique de la classe A est conforme à la norme NMB-003(A)
du Canada.
Le présent produit est conforme aux spécications techniques applicables
d‘Innovation, Sciences et Développement économique Canada.
Disposal of the device
This device is subject to European Directive 2012/19/EU and may not
be disposed of with general household garbage. If you do not know
where to dispose of the device at the end of its lifespan, contact your
municipality, local waste management provider, or vendor.
Cleaning
To clean the device, use an anti-static cloth. Please avoid cleaning liquids as
they might damage the surface or internal electronics of the device.
Connecting the device to the phone
1. Remove the rubber cover from the USB port on the phone (g. C1).
2. Remove the plastic cover around the USB port (g. C2).
3. Plug the USB plug of the expansion module into the USB port on the phone
(g. C3). Use the screws included in the delivery to securely attach the
module. The module is supplied with power via the USB connection.
When more than one expansion module is connected to the phone:
Up to three expansion modules can be daisy-chained to one phone. Daisy-
chain the modules rst. Do not use a USB hub
a. Remove the rubber cover and the plastic cover from the USB port (g.
C1 and C2) of the rst expansion module and plug in the USB plug of
the second module. Use the screws included in the delivery to securely
attach the module.
b. Remove the rubber cover and the plastic cover from the USB port (g. C1
and C2) of the second expansion module and plug in the USB plug of the
third module. Use the screws included in the delivery to securely attach
the module.
c. Attach a power adapter (available separately) to the and second module
to a wall outlet before connecting the daisy-chain to the phone (g. C6).
d. Note: If a USB device like a speakerphone or conferencing device is
connected to the rst (g. C5) or third module (g. C8) in the chain, it may
also need a power adapter.
4. The LEDs on the expansion module(s) will light up briey, then turn o,
indicating that the function keys are now ready for use.
Conguring the function keys
The conguration is done on the Function Keys page of the connected phone‘s
web interface. Please refer to the phone‘s manual, chapter "Conguring the
function keys", at select phone. https://service.snom.com Deskphones
DEUTSCH
Copyright, Markenrechte, Haftungsausschluss
© 2024 Snom Technology GmbH. Alle Rechte reserviert.
Snom sowie die Namen der Snom-Produkte und die Snom-Logos sind gesetz-
lich geschützte Marken der Snom Technology GmbH.
Produktspezikationen können ohne Vorankündigung geändert werden. Snom
Technology GmbH behält sich jederzeit das Recht auf Überarbeitung und Än-
derung dieses Dokumentes vor, ohne verpichtet zu sein, die vorgenommenen
Änderungen anzukündigen oder mitzuteilen.
Trotz der angewandten Sorgfalt bei der Zusammenstellung und Präsentation
der Informationen in diesem Dokument können sich Daten zwischenzeitlich ge-
ändert haben. Daher übernimmt Snom keine Gewähr für die Richtigkeit, Voll-
ständigkeit oder Aktualität der zur Verfügung gestellten Informationen. Jegliche
Haftung für Schäden ist ausgeschlossen, sofern diese nicht auf Vorsatz oder
grober Fahrlässigkeit auf seiten von Snom beruhen oder sofern keine Haftung
aufgrund zwingender gesetzlicher Bestimmungen eintritt.
Wichtige Hinweise
Lesen Sie bitte vor Inbetriebnahme die Sicherheitshinweise und die Bedie-
nungsanleitung. Lassen Sie sie auch von den Mitbenutzern des Gerätes lesen
oder informieren Sie sie über deren Inhalt. Bewahren Sie dieses Dokument auf
und geben Sie das Telefon nur mit ihm an Dritte weiter.
Das Typenschild bendet sich unten oder hinten am Gerät.
Sicherheit
Befolgen Sie die Anweisungen in dieser Bedienungsanleitung und in der sonsti-
gen Dokumentation des Geräts.
• Nur zur beruichen Verwendung mit Snom D8xx-Telefonen. Schließen Sie
das Gerät nicht an einen Computer oder an andere Telefone an!
• Montieren Sie das Gerät nur in Höhen von höchstens 2 m.
• Vermeiden Sie es, die Kabel so zu verlegen, dass sie durch mechanischen
Connecting - Anschließen - Connecter - Conectar - Collegare
Delivery content - Lieferumfang - Contenu de la boîte - En la caja -
Contenuto della confezione
A
C
Expansion Module
for Snom D8xx series
D8C
Quick
Installation
Guide
D8C
v2024002
Attaching the Footstand - Fuß montieren - Attacher le pied -
Montaje el soporte - Fissare il supporto
B
12 3
Snom Technology GmbH
Aroser Allee 66
13407 Berlin, Deutschland
oce.de@snom.com
Snom Technology GmbH
Via Milano 1
20020 Lainate, Italia
oce.it@snom.com
Snom Technology GmbH
The Courtyard, High Street
Ascot, Berkshire SL5 7HP, UK
oce.uk@snom.com
SnomTechnology GmbH
130, avenue Joseph Kessel
78960 Voisins-le-Bretonneux, France
oce.fr@snom.com
VTech Communications Inc.
Snom Americas
9020 Washington Square Road, Suite 555
Tigard, OR 97223
Phone support: (339) 227 6160
VTech Technologies Canada Ltd.
Suite 222, 13888 Wireless Way
Richmond, B.C. V6V 0A3, Canada
Phone support: (339) 227 6160
Manufacturer:
VTech Telecommunications Ltd.
23/F., Tai Ping Industrial Centre,
Block 1,
57 Ting Kok Road, Tai Po
HONG KONG
Not included in delivery
Nicht im Lieferumfang enthalten
Non inclus dans la boîte
Non incluido
Non incluso
C1 C2
C4
C5
C3
USB type A
port
USB type A
plug
5V DC jack
or
C7 C8
C6
Note for D89x phones:
The Snom 15W power supply, Snom PN 00004715, has to be purchased
separately and connected to the DC power jack of the D89x phone when one
or more D8Cs are connected to it.
Detaching the D8C:
1. Remove the screws.
2. Press and slowly
pull the USB plug from
the USB port.
GNU
General Public License

Druck beschädigt werden oder dass Personen darüber stolpern könnten.
• Dieses Gerät ist nur für den Gebrauch in Innenräumen bestimmt - NICHT FÜR
DEN AUSSENBEREICH!
• Stellen Sie das Gerät nicht in Räumen mit hoher Luftfeuchtigkeit wie Bade-
zimmern, Waschküchen, feuchten Kellerräumen auf. Tauchen Sie das Gerät
nicht in Wasser und gießen Sie keine Flüssigkeiten auf oder in das Gerät.
• Stellen Sie das Gerät nicht in explosionsgefährdeten Umgebungen (z.B. La-
ckiereien) auf. Benutzen Sie das Gerät nicht, wenn Sie Gas oder andere mög-
licherweise explosionsgefährliche Dämpfe riechen.
• Telefonieren Sie nicht während eines Gewitters (Stromschlaggefahr bei Blit-
zeinschlag ins Netz).
• Zur Deaktivierung entfernen sie das USB-Kabel und ggf. das Netzteil.
Normkonformität
Dieses Gerät entspricht den grundlegenden Gesundheits-, Sicher-
heits- und Umweltanforderungen aller relevanten europäischen
Richtlinien. Die Konformitätserklärung kann auf www.snom.com/
conformity heruntergeladen werden.
Die eigenmächtige Önung des Geräts sowie Änderungen und Modizierungen
am Gerät führen zum Erlöschen der Gewährleistungspicht und können darü-
berhinaus zum Erlöschen der Zulassungen führen.
• SELV (Safety Extra Low Voltage) Einhaltung: Die Eingangs-/Ausgangsver-
bindungen halten die SELV-Richtlinien für Kleinspannungsgeräte ein.
• Sicherheit: IEC 62368-1
• A nschlüsse:
◦1 USB-Stecker Typ A
◦1 USB-Buchse Typ
◦1 5V DC-Buchse
• Stromspeisung:
Vom Telefon über die USB-Verbindung. Für das zweite Modul benötigen Sie
ein separat erhältliches Netzteil. Das dritte Modul wird über das USB-Kabel
vom zweiten mit Strom versorgt, benötigt jedoch möglicherweise auch ein
Netzteil, wenn ein USB-Gerät daran angeschlossen wird.
◦Mass Power, Modell NBS12E050200UV, SnomPN 00004570 (mit EU-Clip)
Entsorgung des Produkts
Dieses Gerät unterliegt der europäischen Richtlinie 2012/19/EU und darf nicht
im Hausmüll entsorgt werden. Wenn Sie nicht wissen, wo Sie Ihr Altge-
rät entsorgen können, wenden Sie sich bitte an Ihre Kommune, Ihren
örtlichen Müllentsorger oder Ihren Fachhändler.
Reinigung
Benutzen Sie ein antistatisches Tuch. Benutzen Sie kein Wasser und keine Rei-
nigungsüssigkeiten, da sie die Oberäche und die Elektronik des Gerätes be-
schädigen könnten.
Anschließen des Gerätes an das Telefon
1. Entfernen Sie die Gummiabdeckung vom USB-Port des Telefons (Abb. C1).
2. Entfernen Sie die Kunststoabdeckung um den USB-Port (Abb. C2).
3. Stecken Sie den USB-Stecker des Erweiterungsmoduls in den USB-Port des
Telefons (Abb. C3). Benutzen Sie die im Lieferumfang enthaltenen Schrau-
ben, um das Modul sicher zu befestigen. Die Stromversorgung des Moduls
erfolgt über den USB-Anschluss.
Wenn Sie mehr als ein Erweiterungsmodul an ein Telefon anschließen:
Bis zu drei Erweiterungsmodule können an ein Telefon angeschlossen wer-
den. Verbinden Sie zunächst die Module. Verwenden Sie keinen USB-Hub.
a. Entfernen Sie die Gummiabdeckung und die Kunststoabdeckung vom
USB-Port (Abb. C1 und C2) des ersten Erweiterungsmoduls und stecken
Sie den USB-Stecker des zweiten Moduls in den Port. Verwenden Sie
die im Lieferumfang enthaltenen Schrauben, um das Modul sicher zu
befestigen.
b. Entfernen Sie die Gummiabdeckung und die Kunststoabdeckung vom
USB-Port (Abb. C1 und C2) des zweiten Erweiterungsmoduls und stecken
Sie den USB-Stecker des dritten Moduls in den Port. Verwenden Sie
die im Lieferumfang enthaltenen Schrauben, um das Modul sicher zu
befestigen.
c. Schließen Sie ein Netzteil (separat erhältlich) an das zweite Modul und an
eine Steckdose an, bevor Sie die Daisy-Chain mit dem Telefon verbinden
(Abb. C6).
d. Hinweis: Wenn ein USB-Gerät wie eine Freisprecheinrichtung oder ein
Konferenzgerät an das erste (Abb. C5) oder dritte Modul (Abb. C8) in der
Kette angeschlossen ist, ist möglicherweise auch ein Netzteil erforder-
lich.
e. Schließen Sie ein Netzteil (separat erhältlich) an das zweite Modul in der
Reihe an und an die Stromversorgung (Wandsteckdose) an, bevor Sie die
Module mit dem Telefon verbinden.
f. Wenn ein USB-Gerät wie eine Freisprecheinrichtung oder ein Konferenz-
gerät an das dritte Modul angeschlossen ist, benötigt es möglicherweise
auch ein Netzteil,
4. Die LEDs auf dem Erweiterungsmodul bzw. den Modulen leuchten kurz auf
und erlöschen wieder. Die Funktionstasten können jetzt benutzt werden.
Konguration der Funktionstasten
Die Konguration nehmen Sie im Webbrowser des angeschlossenen Telefons
auf der Seite "Funktionstasten" vor. Die Anleitung dazu nden Sie in der Bedie-
nungsanleitung des Telefons, Kapitel "Die Programmierung der Funktionstas-
ten", auf unserer Webseite, https://service.snom.com Tischtelefone .
FRANÇAIS
Copyright, Marques Déposées, GPL, Non Responsabilitée
© 2024 Snom Technology GmbH. Tous droits réservés.
Snom, les noms des produits Snom et les logos Snom sont des marques
déposées par Snom Technology GmbH.
Toutes les spécications du produit sont sujet à modications sans préavis. Snom
Technology GmbH se réserve le droit de modier et de changer ce document
à n‘importe quel moment, sans devoir annoncer de telles modications ou
changements avant ou après leur mise en place. Bien que le plus grand soin
ait été apporté à la compilation et à la présentation des informations contenues
dans ce document, les données sur lesquelles elles sont basées peuvent entre-
temps avoir été modiées. Snom doit donc décliner toute garantie et toute
responsabilité quand à l‘exactitude et à l‘exhaustivité des informations publiées
excepté en cas de négligence agrante de la part de Snom ainsi que des les cas
ou la responsabilité de Snom est engagée de par la loi.
Informations importantes
Veuillez lire les informations concernant la sécurité et la mise au rebut de
l‘appareil ainsi que celles concernant son installation et son utilisation avant
d‘utiliser buanmderl‘appareil. Communiquez également ces informations aux
autres utilisateurs. Gardez ce manuel et ne cédez pas l‘appareil à une tierce
partie sans le manuel.
La plaque signalétique est située en bas ou à l'arrière du produit.
Sécurité
Suivez les instructions présentes dans ce manuel et dans les autres documents
concernant l‘appareil. La plaque signalétique est située en bas ou à l'arrière du
produit.
• Cet appareil est destiné à une utilisation professionnelle avec un téléphone
Snom D8xx. Ne pas brancher au PC ni à d'autres téléphones!
• Montez l'appareil uniquement à des hauteurs ne dépassant pas 2m.
• Cet appareil est destiné à une utilisation en intérieur uniquement! Ne
l’installez pas au dehors!
• N’installez pas l’appareil dans des pièces très humides (par exemple, dans
une salle de bain ou un sous-sol humide). N’immergez pas l’appareil dans
l’eau et ne versez pas de liquides d’aucune sorte sur ou dans l’appareil.
• N’installez pas l’appareil dans un lieu présentant un risque d’explosion (un
magasin de peinture par exemple). N’utilisez pas l’appareil si vous sentez une
odeur de gaz ou d’autres émanations potentiellement explosives.
• N’utilisez pas l’appareil durant les orages, le choc d’un éclair sur les circuits
électriques peut provoquer une électrocution.
Conformité au standards
Cet appareil est marqué CE et conforme aux standards de sécurité,
de santé et environnementaux de tous les directives européennes
applicables.
Cet appareil est conforme aux normes de santé, de sécurité et
environnementales des États-Unis et du Canada.
La déclaration de conformité peut être téléchargée sur
www.snom.com/conformity..
L'ouverture et la modication de l'appareil sans autorisation annule la
garantie et peut également annuler la conformité CE. En cas de mauvais
fonctionnement, veuillez contacter le personnel d'entretien agrée, votre
revendeur ou bien Snom.
• SELV - TBTS (Très Basse Tension de Sécurité) : Le niveau de sécurité des
connexions d‘entré/sortie est conforme aux recommandations SELV /TBTS.
• Sécurité: IEC 62368-1
• Connecteurs
◦1 x prise USB type A mâle
◦1 x port USB type A
◦1 x prise d'alimentation 5V DC
• Alimentation:
Fourni par le téléphone via le connecteur USB. a Le deuxième module
besoin d'un bloc d’alimentation. Le troisième module peut également avoir
besoin d'un bloc d'alimentation si un dispositif USB est connecté à son port
USB. Le bloc d'alimentation est vendu séparément, Mass Power, modèle
NBS12E050200UV, Snom PN 00004570
◦UE : livré avec des clips UE et Royaume-Uni
◦États-Unis/Canada : livré avec un clip américain
Informations complémentaires importantes Industrie Canada
Cet appareil numérique de la classe A est conforme à la norme NMB-003(A)
du Canada.
Le présent produit est conforme aux spécications techniques applicables
d‘Innovation, Sciences et Développement économique Canada
Mise au rébut
Cet appareil est soumis à la Directive 2012/19/EU et ne peut être mis
au rebut avec les déchets ménagers normaux. Si vous ne savez pas ou
mettre au rebut oú faire recycler l'appareil lorsqu'il arrive au terme de
son existence, contactez votre municipalité, la société locale en charge de la
gestion des déchets ou votre vendeur.
Nettoyage
Utilisez un tissu antistatique. N‘utilisez pas de l‘eau ou un produit de nettoyage
liquide ou solide. Ils peuvent endommager l‘éléctronique ou les sufaces de
l‘appareil.
Connecter le dispositif au téléphone
1. Retirez le cache en caoutchouc du port USB du téléphone (g. C1).
2. Retirez le cache en plastique autour du port USB (g. C2).
3. Branchez la che USB du module d'extension dans le port USB du téléphone
(g. C3). Utilisez les vis incluses dans la livraison pour xer solidement le
module. Le module est alimenté via la connexion USB.
Lorsque plusieurs modules d'extension sont connectés au téléphone:
a. Jusqu'à trois modules d'extension peuvent être connectés en série à un
téléphone. Commencez par connecter en série les modules. N'utilisez pas
de hub USB
b. Retirez le cache en caoutchouc et le cache en plastique du port USB (g.
C1 et C2) du premier module d'extension et branchez la prise USB du
deuxième module. Utilisez les vis incluses dans la livraison pour xer
solidement le module.
c. Retirez le cache en caoutchouc et le cache en plastique du port USB (g.
C1 et C2) du deuxième module d'extension et branchez la prise USB du
troisième module. Utilisez les vis incluses dans la livraison pour xer
solidement le module.
d. Branchez un bloc d'alimentation (disponible séparément) au deuxième
module et à une prise murale avant de connecter la chaîne de modules au
téléphone (g. C6).
e. Attention: Si un périphérique USB tel qu'un haut-parleur ou un appareil
de conférence est connecté au premier (g. C5) ou au troisième module
(g. C8) de la chaîne, il peut également nécessiter un bloc d'alimentation.
4. Les DEL du module/des modules d'extension vont s'allumer brièvement et
puis s'éteindre. Ensuite vous pourrez les utiliser.
Congurer les touches de fonction
La conguration des touches fonction doit être eectuée sur l'interface
web du téléphone branché, page "Touches de fonction". Pour plus des
informations consultez le mode d‘emploi du téléphone sur notre site web
https://service.snom.com Deskphones .
ITALIANO
Copyright, marchi registrati, GPL, declinazione di responsabilita
© 2024 Snom Technology GmbH. Tutti i diritti riservati.
Snom, i nomi dei prodotti Snom, ed i loghi Snom sono marchi registrati di prop-
rietà di Snom Technology GmbH.
Le speciche tecniche del prodotto qui contenute possono essere variate
senza previa notica. Snom Technology GmbH si riserva il diritto di rivedere e
modicare il presente documento in qualsiasi momento senza alcun obbligo di
notica precedente o posteriore a tali cambiamenti. Sebbene sia stata prestata
la massima attenzione nella stesura e presentazione delle informazioni in
questo documento, i dati su cui si basa potrebbero già aver subito variazioni.
Snom pertanto declina ogni responsabilità riguardo a tutte le garanzie di
adabilità, accuratezza, completezza ed attualità delle informazioni pubblicate,
tranne nel caso di grossolana negligenza da parte di Snom o laddove per legge
possa essere ritenuta responsabile.
Informazioni importanti
Pregasi leggere con attenzione le istruzioni inerenti la sicurezza, lo smaltimento
e l‘installazione del dispositivo prima del suo impiego. Tali informazioni vanno
condivise con gli altri utenti. È altresì necessario conservare questo manuale,
consegnandolo insieme al dispositivo qualora esso venga dato a terzi.
La targhetta si trova nella parte inferiore o posteriore del prodotto.
Sicurezza
Seguite le istruzioni in questo manuale e tutta la documentazione relativa al
dispositivo. .
• Questo dispositivo è destinato all‘uso professionale con telefoni Snom D8xx.
Non collegare al PC o ad altri telefoni!
• Montare il dispositivo solo ad altezze non superiori a 2 m.
• Non posizionare il cavo del dispositivo dove può essere calpestato. Non
posizionare il cavo del dispositivo dove può essere soggetto a pressione
meccanica perchè potrebbe danneggiare il cavo.
• Il dispositivo si può impiegare solo al chiuso! Non installare all’aperto!
• Non installare il dispositivo in ambienti con alta umidità (ad es., in bagno,
lavanderia, seminterrati umidi). Non immergere il dispositivo in acqua e non
versarvi liquidi sopra
• Non installare il dispositivo nei pressi di locali a rischio esplosione (colorici,
ad es.). Non utilizzare il dispositivo se sentite odore di gas o di altra esalazione
potenzialmente esplosiva.
• Non utilizzare il dispositivo durante i temporali. Qualora un fulmine colpisca
la rete elettrica, è passibile di scossa.
Conformità
Il dispositivo è dotato di marcatura CE e risponde agli standard eu-
ropei di salute, sicurezza ed ambientali. La dichiarazione di confor-
mità può essere scaricata da www.snom.com/conformity.
Eventuali modiche, cambiamenti e l’apertura non autorizzata del dispositivo
invalidano la garanzia e potrebbero annullare la marcatura CE. In caso di
malfunzionamenti, contattare il servizio di assistenza autorizzato, il rivenditore
oppure Snom.
• SELV ): Il nivello di scurezza dei circuiti in (bassissima tensione di sicurezza
ingresso / uscita è conforme alle raccomandazioni SELV.
• Sicurezza: IEC 62368-1
• Connettore:
◦1 x spino USB standard di tipo A;
◦1 x port USB di tipo A,
◦1x jack di alimentazione da 5V DC
• Potenza:
Fornito dal telefono tramite il connetore USB. Per il secondo modulo, è
necessario utilizzare un alimentatore. Il terzo modulo, se vi è connesso
un dispositivo USB, potrebbe richiedere un alimentatore. L'alimentatore è
venduto separatamente: Mass Power, model NBS12E050200UV, Snom PN
00004570 (spedito con clip UE).
Smaltimento
Questo dispositivo è soggetto alla Direttiva Europea 2012/19/EU e non
può essere smaltito con i riuti domestici. Se non sapete come smaltire
l’apparecchio una volta inutilizzabile, contattate il comune, la nettezza
urbana locale, o il vostro rivenditore.
Collegare il dispositivo al telefono
1. Rimuovere la copertura in gomma dalla porta USB del telefono (g. C1).
1. Rimuovere la copertura in plastica attorno alla porta USB (g. C2).
1. Collegare la spina USB del modulo di espansione alla porta USB del telefono
(g. C3). Utilizzare le viti incluse nella consegna per ssare saldamente il mo-
dulo. Il modulo viene alimentato tramite la connessione USB.
Quando al telefono è collegato più di un modulo di espansione:
a. È possibile collegare a catena no a tre moduli di espansione a un telefo-
no. Collegare prima i moduli a margherita. Non utilizzare un hub USB
b. Rimuovere la copertura in gomma e quella in plastica dalla porta USB
(g. C1 e C2) del primo modulo di espansione e collegare la presa USB
del secondo modulo. Utilizzare le viti incluse nella consegna per ssare
saldamente il modulo.
c. Rimuovere la copertura in gomma e quella in plastica dalla porta USB
(g. C1 e C2) del secondo modulo di espansione e collegare la presa USB
del terzo modulo. Utilizzare le viti incluse nella consegna per ssare
saldamente il modulo.
d. Collegare un alimentatore (disponibile separatamente) al secondo modulo
e ad una presa a muro prima di collegare il collegamento a margherita al
telefono (g. C6).
e. Nota: se un dispositivo USB come un vivavoce o un dispositivo per confe-
renze è collegato al primo (g. C5) o al terzo modulo (g. C8) della catena,
potrebbe essere necessario anche un alimentatore.
4. Le spie LED sui moduli d'espansione si accenderanno brevemente e poi si
spegneranno, ad indicare che da quel momento i tasti funzione saranno
pronti all'uso.
Congurare i tasti funzione
La congurazione dei tasti funzione deve essere eseguita nella pagina
"Tasti Funzione" dell'interfaccia web del telefono collegato. Per le modalità,
consultare il manuale del telefono d'uso alla nostra pagina web,
https://service.snom.com Deskphones .
ESPAÑOL
Propriedad intelectual, marcas registradas, exencion de
responsabilidad
© 2024 Snom Technology GmbH: Todos los derechos reservados.
Snom, los nombres de los productos Snom, y los logos de Snom son marcas
comerciales propiedad de Snom Technology GmbH.
Las especicaciones de producto que aparecen en este documento están sujetas
a cambios sin previo aviso Snom Technology GmbH se reserva el derecho de
revisar y modicar este documento en cualquier momento, sin obligación de
noticar estas revisiones o modicaciones por adelantado o con posterioridad
a su realización. Aunque se han tomado todas las precauciones posibles
en la compilación y presentación de la información de este documento, los
datos en los que se basa pueden haber cambiado con el tiempo. Snom, por lo
tanto, renuncia a cualquier garantía y responsabilidad respecto a la precisión,
exhaustividad y vigencia actual de la información publicada, excepto en el caso
de intencionalidad o negligencia grave por parte de Snom cuando se deriven
responsabilidades de acuerdo con las disposiciones legales vinculantes.
Información importante
Lea las instrucciones sobre seguridad telefónica y reciclaje del teléfóno, y sobre
cómo congurar y utilizar el teléfono antes de usarlo, y ofrézcalas igualmente a
otros usuarios para que las lean o se informen de su contenido. Conserve este
manual y no entregue el teléfono a terceros sin el mismo.
La placa de identicación se encuentra en la parte inferior o posterior del
producto.
Seguridad
Siga las instrucciones de este manual y otra documentación aplicable del dispositivo.
• Este dispositivo está diseñado para uso profesional con teléfonos Snom D8xx. ¡No
conectar al ordenador o a otros teléfonos!
• Montare il dispositivo solo ad altezze non superiori a 2m.
• Evite poner el cable de alimentación del teléfono de modo que otras personas
puedan tropezar con el mismo. No coloque el cable de alimentación del teléfono de
forma que pueda verse sometido a presiones mecánicas, ya que eso podria dañar
el cable. Si el cable de alimentación o el enchufe están dañados, desconecte el
teléfono y contacte con personal de servicio cualicado.
• Este dispositivo es solamente para uso en interiores. No debe instalarse en el
exterior.
• No instale el teléfono en lugares con humedad elevada (por ejemplo, en baños,
lavaderos, o sótanos húmedos). No sumerja el teléfono en agua ni derrame o vierta
líquidos de ningún tipo sobre el teléfono.
• No instale el teléfono cerca de lugares con riesgo de explosión (talleres de pintura, por
ejemplo). No use el teléfono si huele a gas o a otros vapores que puedan ser explosivos.
• No use el teléfono durante una tormenta; los rayos que impacten en la red eléctrica
pueden provocar descargas eléctricas.
Cumplimiento con la normativa
Este dispositivo tiene el marcado CE y la certicación FCC, y cumple con los
estándares de salud, seguridad y medioambientales europeos y de Estados
Unidos. La declaración de conformidad se puede descargar desde
www.snom.com/conformity.
Todas las modicaciones, los cambios y la apertura no autorizada del dispositivo
provocarán la cancelación de la garantia, y también pueden causar la perdida del
marcado CE y de la certicación FCC.
• SELV (Tensión Extra-Baja de Seguridad): Las condiciones de seguridad de las
conexiones de entrada/salida cumplen con los requisitos SELV.
• Seguridad: IEC 62368-1
• Conectores:
◦1 x conector USB 2.0 estándar de tipo A
◦1 x puerto USB tipo A
◦1 x conector de alimentación de 5V DC
• Alimentación:
Suministrado por el teléfono a través del conector USB. Para el segundo módulo
es necesario utilizar una fuente de alimentación. El tercer módulo también
podría necesitar una fuente de alimentación si tiene un dispositivo conectado en
su puerto USB. La fuente de alimentación se vende por separado: Mass Power,
modello NBS12E050200UV, Snom PN 00004570.
◦UE/UK: enviado con clips de UE y UK
◦U.S./Canada: enviado con clip des Ètats Unis
Limpieza
Use un paño antiestática. No utilice agua ni productos de limpieza, ya que podrían
dañar la supercie o los componentes electrónicos del aparato.
Eliminación
Este dispositivo está sujeto a la Directriz Europea 2012/19/EU, y no puede
ser eliminado con los residuos domésticos generales. Si no sabe dónde puede
desechar el dispositivo al nal de su vida útil, contacte con su municipio, su
proveedor de gestión de residuos local, o su vendedor.
Conectar el dispositivo al teléfono
1. Retire la tapa de goma del puerto USB del teléfono (g. C1).
2. Retire la cubierta de plástico que rodea el puerto USB (g. C2).
3. Conecte el conector USB del módulo de expansión al puerto USB del teléfono (g.
C3). Utilice los tornillos incluidos en la entrega para jar de forma segura el módulo.
El módulo recibe alimentación a través de la conexión USB.
En caso de que se conecten al teléfono dos o tres módulos de expansión:
a. Se pueden conectar en cadena hasta tres módulos de expansión a un teléfono.
Primero conecte en cadena los módulos. No utilice un concentrador USB
b. Retire la cubierta de goma y la cubierta de plástico del puerto USB (g. C1 y
C2) del primer módulo de expansión y conecte el conector USB del segundo
módulo. Utilice los tornillos incluidos en la entrega para jar de forma segura
el módulo.
c. Retire la cubierta de goma y la cubierta de plástico del puerto USB (g. C1 y C2)
del segundo módulo de expansión y conecte el conector USB del tercer módulo.
Utilice los tornillos incluidos en la entrega para jar de forma segura el módulo.
d. Conecte un adaptador de corriente (disponible por separado) al segundo módu-
lo y a un tomacorriente de pared antes de conectar la cadena tipo margarita al
teléfono (g. C6).
e. Nota: Si un dispositivo USB, como un altavoz o un dispositivo de conferencia,
está conectado al primer (g. C5) o al tercer módulo (g. C8) de la cadena, es
posible que también necesite un adaptador de corriente.
4. Los indicadores LED de los módulos de expansión se encenderán brevemente y a
continuación se apagarán para indicar que a partir de ese momento las teclas de
función están listas para el uso.
Conguración de las teclas de función
La conguración de las teclas de función se debe efectuar en la página "Teclas de
Funcion" del interfaz web del teléfono conectado. Para más información, consulte
el manual del teléfono en nuestra página web, https://service.snom.com
Deskphones.
Specyfikacje produktu
Marka: | Snom |
Kategoria: | Nie skategoryzowane |
Model: | D8C |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Snom D8C, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Nie skategoryzowane Snom

4 Marca 2025

4 Marca 2025
Instrukcje Nie skategoryzowane
- Nie skategoryzowane Ikea
- Nie skategoryzowane Samsung
- Nie skategoryzowane AEG
- Nie skategoryzowane Beko
- Nie skategoryzowane LG
- Nie skategoryzowane Worx
- Nie skategoryzowane Smeg
- Nie skategoryzowane Gaggia
- Nie skategoryzowane Honda
- Nie skategoryzowane Philips
- Nie skategoryzowane SilverCrest
- Nie skategoryzowane Bosch
- Nie skategoryzowane Parkside
- Nie skategoryzowane Whirlpool
- Nie skategoryzowane Roland
- Nie skategoryzowane Miele
- Nie skategoryzowane Easy Home
- Nie skategoryzowane Nokia
- Nie skategoryzowane Hisense
- Nie skategoryzowane StarTech.com
- Nie skategoryzowane Theben
- Nie skategoryzowane Crestron
- Nie skategoryzowane Asus
- Nie skategoryzowane Black & Decker
- Nie skategoryzowane Hazet
- Nie skategoryzowane Conair
- Nie skategoryzowane RIKON
- Nie skategoryzowane Blaupunkt
- Nie skategoryzowane IOptron
- Nie skategoryzowane Iiyama
- Nie skategoryzowane Lincoln Electric
- Nie skategoryzowane Metra
- Nie skategoryzowane Manhattan
- Nie skategoryzowane Microchip
- Nie skategoryzowane Heritage Audio
- Nie skategoryzowane Tripp Lite
- Nie skategoryzowane Shure
- Nie skategoryzowane Shimano
- Nie skategoryzowane TFA
- Nie skategoryzowane Icy Box
- Nie skategoryzowane RYOBI
- Nie skategoryzowane Alpine
- Nie skategoryzowane Gembird
- Nie skategoryzowane LogiLink
- Nie skategoryzowane Polaris
- Nie skategoryzowane IFM
- Nie skategoryzowane Moulinex
- Nie skategoryzowane Biltema
- Nie skategoryzowane Digitus
- Nie skategoryzowane Vimar
- Nie skategoryzowane V-TAC
- Nie skategoryzowane Emos
- Nie skategoryzowane AVMATRIX
- Nie skategoryzowane Corbero
- Nie skategoryzowane Morphy Richards
- Nie skategoryzowane Crivit
- Nie skategoryzowane Everdure
- Nie skategoryzowane La Crosse Technology
- Nie skategoryzowane Neumann
- Nie skategoryzowane Victron Energy
- Nie skategoryzowane Pyle
- Nie skategoryzowane Texas
- Nie skategoryzowane Panduit
- Nie skategoryzowane CRUX
- Nie skategoryzowane KitchenAid
- Nie skategoryzowane EchoMaster
- Nie skategoryzowane Esoteric
- Nie skategoryzowane Chord
- Nie skategoryzowane Speco Technologies
- Nie skategoryzowane ARRI
- Nie skategoryzowane Fluke
- Nie skategoryzowane Bogen
- Nie skategoryzowane Pulsar
- Nie skategoryzowane Exquisit
- Nie skategoryzowane Chief
- Nie skategoryzowane Arçelik
- Nie skategoryzowane AirLive
- Nie skategoryzowane Audio-Technica
- Nie skategoryzowane Planet
- Nie skategoryzowane Rocktrail
- Nie skategoryzowane JL Audio
- Nie skategoryzowane Konica Minolta
- Nie skategoryzowane Inventum
- Nie skategoryzowane Ariete
- Nie skategoryzowane LiftMaster
- Nie skategoryzowane Taga Harmony
- Nie skategoryzowane Argoclima
- Nie skategoryzowane Livarno Lux
- Nie skategoryzowane Marmitek
- Nie skategoryzowane Smart-AVI
- Nie skategoryzowane Cameo
- Nie skategoryzowane Schwaiger
- Nie skategoryzowane Mean Well
- Nie skategoryzowane Gravity
- Nie skategoryzowane Kenmore
- Nie skategoryzowane Deaf Bonce
- Nie skategoryzowane Sangean
- Nie skategoryzowane Playtive
- Nie skategoryzowane ZKTeco
- Nie skategoryzowane True
- Nie skategoryzowane Nebula
- Nie skategoryzowane Hitachi
- Nie skategoryzowane CyberPower
- Nie skategoryzowane Black Diamond
- Nie skategoryzowane Fieldmann
- Nie skategoryzowane Soundskins
- Nie skategoryzowane Vivanco
- Nie skategoryzowane Leifheit
- Nie skategoryzowane Lectrosonics
- Nie skategoryzowane Hobart
- Nie skategoryzowane Kanto
- Nie skategoryzowane Lumens
- Nie skategoryzowane HQ Power
- Nie skategoryzowane BioChef
- Nie skategoryzowane Vicoustic
- Nie skategoryzowane Elgato
- Nie skategoryzowane SureFire
- Nie skategoryzowane Savio
- Nie skategoryzowane RADEMACHER
- Nie skategoryzowane Crosley
- Nie skategoryzowane HK Audio
- Nie skategoryzowane Ideal
- Nie skategoryzowane Proscan
- Nie skategoryzowane Lava
- Nie skategoryzowane Simplified MFG
- Nie skategoryzowane Musway
- Nie skategoryzowane Hansa
- Nie skategoryzowane Livarno
- Nie skategoryzowane Melinera
- Nie skategoryzowane GeoVision
- Nie skategoryzowane Brabantia
- Nie skategoryzowane Godrej
- Nie skategoryzowane Vizio
- Nie skategoryzowane DoorBird
- Nie skategoryzowane Nevadent
- Nie skategoryzowane Genelec
- Nie skategoryzowane Vorago
- Nie skategoryzowane Expobar
- Nie skategoryzowane PAC
- Nie skategoryzowane ColorKey
- Nie skategoryzowane Fischer
- Nie skategoryzowane Keter
- Nie skategoryzowane Berker
- Nie skategoryzowane Atdec
- Nie skategoryzowane Wise
- Nie skategoryzowane MuxLab
- Nie skategoryzowane Extron
- Nie skategoryzowane Pigtronix
- Nie skategoryzowane Morningstar
- Nie skategoryzowane Brinno
- Nie skategoryzowane Legrand
- Nie skategoryzowane NovaStar
- Nie skategoryzowane Parasound
- Nie skategoryzowane DB Technologies
- Nie skategoryzowane Needit
- Nie skategoryzowane Berkel
- Nie skategoryzowane Phoenix Contact
- Nie skategoryzowane Morphor
- Nie skategoryzowane Fluance
- Nie skategoryzowane Buchla & TipTop Audio
- Nie skategoryzowane On-Q
- Nie skategoryzowane SetonixSynth
- Nie skategoryzowane Planet Audio
- Nie skategoryzowane Hedbox
- Nie skategoryzowane IPEGA
- Nie skategoryzowane Oras
- Nie skategoryzowane Royal Catering
- Nie skategoryzowane Qu-Bit
- Nie skategoryzowane IMG Stageline
- Nie skategoryzowane PUR
- Nie skategoryzowane Rexing
- Nie skategoryzowane IDIS
- Nie skategoryzowane I-PRO
- Nie skategoryzowane Senseca
- Nie skategoryzowane Ruggard
- Nie skategoryzowane DQ
- Nie skategoryzowane XTRARM
- Nie skategoryzowane Ingenuity
- Nie skategoryzowane Phase Technology
- Nie skategoryzowane CkeyiN
- Nie skategoryzowane Casr
- Nie skategoryzowane Hypnos
- Nie skategoryzowane BlaknBlu
- Nie skategoryzowane Louroe Electronics
- Nie skategoryzowane Orbitrek
- Nie skategoryzowane Zaahn
- Nie skategoryzowane Kaorka
- Nie skategoryzowane MOOOV
- Nie skategoryzowane Crem
- Nie skategoryzowane Zeapon
- Nie skategoryzowane CLIMAQUA
- Nie skategoryzowane Tece
- Nie skategoryzowane Sportime
- Nie skategoryzowane Quasar Science
- Nie skategoryzowane Beltronics
Najnowsze instrukcje dla Nie skategoryzowane

15 Marca 2025

14 Marca 2025

14 Marca 2025

14 Marca 2025

14 Marca 2025

14 Marca 2025

14 Marca 2025

14 Marca 2025

14 Marca 2025

14 Marca 2025