Instrukcja obsługi Smeg CK2000LED

Smeg Okap wyciągowy CK2000LED

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Smeg CK2000LED (32 stron) w kategorii Okap wyciągowy. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/32

INSTRUCTIONS FOR INSTALLATION AND USE

MONTAGE- UND GEBRAUCHSANWEISUNG

INSTRUCTIONS POUR L'INSTALLATION ET L’UTILISATION

ISTRUZIONI PER L'INSTALLAZIONE E L’USO

INSTRUCCIONES PARA INSTALACIÓN Y USO

INSTRUÇÕES DE INSTALAÇÃO Y UTILIZAÇÃO

AANWIJZING VOOR GEBRUIK EN INSTALLATIE

ИНСТРУКЦИИ ПО ПОЛЬЗОВАНИЮ

ENGLISH

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified

persons in order to avoid a hazard.

Only for hoods equipped with electronic control:

The 4th speed (intensive) is automatically lowered to 3rd speed after 5 minutes of operation to optimise energy

consumption; in hoods with voltage 120V/60Hz this function is not active and the 4th speed is indicated by

the letter b (Booster).

- If the hood is left on (lights and/or motor), after 10 hours in the absence of commands from the user, it will

automatically switch to OFF condition with all services switched off. In hoods with voltage 120V/60Hz this function

is not active.

- The Buzzer emits a “beep” each time that a command is set from the keyboard or remote control (optional).

- In the event of interruption of power during the hood, if you restore the hood in the OFF state, then the engine

must be reactivate manually.

Warning: Failure to install the screws or fixing device in accordance with these instructions may result

electrical hazards.

DESCRIPTION

The hood may be installed in the filtering or the ducting version. Filtering version (Fig. 1): The hood aspirates

the kitchen air saturated with fumes and odours, purifies it through the grease filters and charcoal filters and returns

clean air into the room. For constant efficiency, the charcoal filters must be replaced periodically. The charcoal

filters are not supplied. Ducting version (Fig. 2): The hood aspirates the kitchen air saturated with fumes and

odours, passes it through the grease filters and expels it to the outside through an outlet pipe. With this version

the charcoal filters are not required.

Decide from the outset on the type of installation (filtering or ducting). For greater efficiency, we recommend

you install the hood in the ducting version (if possible).

The 2-motor version hood is only available for ducting version installation.

INSTALLATION

ATTENTION: 2 people are required for proper installation; the unit should be installed by a qualified

operator.

INSTALLATION IN DUCTING VERSION:

1. Before fixing, the disposal duct for air evacuation to the outside must be installed. Use an disposal duct

with: – minimum indispensable length; – minimum possible bends (maximum angle of bend: 90°); – certified material

(according to the State); – an as smooth as possible inside. It is also advisable to avoid any drastic changes

in pipe cross-section. We recommend using a 150 mm diameter pipe for model shown in Figure 3, and a 200 mm

diameter pipe for the model shown in Figure 4. For air evacuation to the outside, follow all the other instructions

given on the “Warnings” sheet.

2. If you have purchased the 2-motor version (model shown in Fig. 4), you must fit the plastic flange using

4 screws (3,9 x 9,5 mm).

3. Prepare a suitable power supply. For the electrical connection, follow all the other instructions on the

“Warnings” sheet.

4. Check to see the grease filters have been removed; if necessary, remove these by moving the catch

(B) and turning these outwards (Fig. 5).

5. Make a hole for housing the appliance (Fig.6) in the bottom of the wall unit. The bottom of the wall unit

must have a thickness of between 15 and 20 mm.

6. Take 4 retention screws from the accessories bag (4,2 x 15 mm). Fit the appliance in the hole made

on the wall unit, first positioning the rear part, so the flap on the back rests on the wall unit; next, slightly slide

the appliance back, towards the wall (Fig. 7).

Without leaving the appliance, secure this to the wall unit by means of the 4 screws (Fig. 8).

7. Proceed with final fitting, using the 4 screws (4,2 x 15 mm); See Fig. 9.

8. Connect the disposal duct to the air evacuation pipe of the hood. Use a flexible pipe and lock it to the

air evacuation pipe of the hood with a metal hose clamp (pipe and clamp are not provided). Make the electrical

connections.

9. Refit the grease filters.

INSTALLATION IN FILTERING VERSION:

Proceed with installation, making reference to the instructions for the extraction version (see points 3, 4, 5,

6, 7), and then follow the instructions below.

Connect the hose to the hood air outlet so the air is conveyed to the top of the wall unit; secure the hose

with a metal clamp (hose and clamp are not provided). Make power connections.

Check whether the charcoal filters have already been fitted. If necessary, proceed to fit these as follows:

rest the charcoal filter on the motor unit by making the pins coincide; turn the charcoal filter until this is fast

(Fig. 10).

Refit the grease filters.

OPERATION

Depending on the model, the unit is equipped with the following controls:

Controls shown in Fig. 11: Button A = turns the lights on/off. Button B = turns the TIMER on/off: press

once to turn the timer on, therefore, after 5 minutes, the motor cuts out (at the same time the selected speed

blinks on the display); the timer remains on if the motor speed is changed. Display C = - indicates the selected

motor speed (from 1 to 4); - indicates Timer On when the number blinks; - indicates Filter Alarm when the central

segments is on or blinking. Button D = makes the motor work (at the last speed selected); pushing the button

again, the speeds of the motor are sequentially selected from 1 to 4; keeping this button pressed for about 2

seconds shuts down the motor. Button R = resets the grease filters or charcoal filters; when the filter alarm

appears (i.e. when the central segment on the display goes on), the grease filters must be cleaned (30 hours

of operation); when the central segment starts blinking, the grease filters must be cleaned and the charcoal filters

replaced (120 hours of operation). Obviously, if the hood is not a filtering model and does not have a charcoal

filter, clean the grease filters both when the central segment goes on and when it starts blinking. The filter alarm

can be seen when the motor is off and for about 30 seconds. To reset the hour counter, keep the button pressed

for 2 seconds while the alarm can be seen.

Controls shown in Fig. 12:

AUTOMATIC OPERATION WITH SENSOR:

Key A : switches the lights on/off. Key B : enables/disables “Automatic” function. When this function is selected,

an “A” appears on the display C, and the speed of the motor increases or decreases depending on the smoke,

odours and gas present in the kitchen. Display C : - indicates the automatic operation of the sensor (the

letter “A” appears);- indicates the motor speed selected automatically by the sensor; indicates the filter alarm

whenever the central segment is illuminated or flashing. Key D : decreases motor speed / Reset; decreases

motor speed to zero (stopping); in any case however, after approximately 1 minute, the hood resumes automatic

operation at the speed set by the sensor. Whenever the key is pressed during the display of filter alarms,

a RESET occurs, and the counting of the hours resumes again. Key E : increases motor speed; in any case

however, after approximately 1 minute, the hood resumes automatic operation at the speed set by the sensor.

Modification of sensor sensitivity: sensor sensitivity can be modified by operating as follows:

- stop the hood by pressing key B. – Simultaneously press keys D and E (the sensor’s sensitivity index will

appear on the display) - Pressing keys D or E, the sensor’s sensitivity will either increase or decrease (1

: minimum sensitivity / 9: maximum sensitivity). – whenever the power supply is interrupted, the sensor will

resume operation with a sensitivity index of 5.

Warning: in order to avoid damaging the sensor, never use silicone products near the hood!

OPERATION AS TRADITIONAL HOOD:

Key A : switches the lights on/off. Display C : - indicates the motor speed selected (from 1 to 4); - indicates

the operation of the Timer when the number is flashing; - indicates filter alarms whenever the central segment

is illuminated or flashing. Key D : decreases motor speed / Stop / Reset; decreases motor speed to zero

(stopping). Whenever the key is pressing during filter alarm display, a RESET occurs, and the counting of the

hours resumes again. Key E : enables the motor / increases motor speed /TIMER. Pressing this key starts

the motor (at the latest speed set); pressing the key again increases motor speed, while keeping the key pressed

down for a few seconds enables the TIMER, and 5 minutes later the motor will stop (while the number of speed

setting selected will simultaneously begin flashing on the display); the Timer will remain enabled if motor speed

is changed. In order to disable the Timer, press the key again.

Controls shown in Fig. 13:

A) Turns the lights off.

B) Turns the lights on.

C) Reduces the motor speed until reaching zero. If pressed for 2" when the Filter Alarm is active, the HOUR counter

is reset.

D) Drives the motor (calling the last speed used) and increases the speed until reaching maximum.

E) Activates/deactivates the sensor (AUTOMATIC or MANUAL mode). In Automatic mode the sensor is active and

the letter “A” appears on the display (L).

L) Display:

- signals the running speed

- signals Automatic mode by displaying the letter “A”. When the motor speed is changed, the running speed is

displayed flashing 3 times, and then the letter “A” reappears.

- signals the filter alarm (with motor off) by displaying the central segment for 30".

FILTER ALARM: Displayed for 30" when the motor is off:

After 30h of operation the central segment lights up on the display; It indicates that the grease filters need to

be cleaned.

After 120h of operation, the central segment flashes on the display; It indicates that the grease filters need to

be cleaned and the charcoal filters replaced.

After cleaning the grease filters (and/or replacing the charcoal filters), restart the hour counter (RESET) by pressing

the key C during display of the filter alarm.

GAS SENSOR SENSITIVITY: The sensitivity of the sensor can be modified to suit your requirements. To modify

the sensitivity, the appliance must be in manual mode (i.e. the running speed and not the letter “A” must appear

on the display); If not, press the key E.

Modify the sensitivity by simultaneously pressing the keys D and E. The set sensitivity is indicated on the display.

By means of the buttons C(-) and D(+) the desired sensitivity is set Store the “new” sensitivity by pressing the

key E.

Specyfikacje produktu

Marka:	Smeg
Kategoria:	Okap wyciągowy
Model:	CK2000LED

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Smeg CK2000LED, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Okap wyciągowy Smeg

Smeg KSCF90B Instrukcja

13 Stycznia 2025

Smeg KDD60VXE-3 Instrukcja

3 Stycznia 2025

Smeg KICGR70X2 Instrukcja

3 Stycznia 2025

Smeg KSET96E2 Instrukcja

3 Stycznia 2025

Smeg KSET66E2 Instrukcja

3 Stycznia 2025

Smeg KSP90HXE Instrukcja

23 Grudnia 2024

Smeg KSET66VBE2 Instrukcja

23 Grudnia 2024

Smeg KSET600HXE Instrukcja

23 Grudnia 2024

Smeg KE61NEE Instrukcja

23 Grudnia 2024

Smeg KQR45NE Instrukcja

23 Grudnia 2024

Instrukcje Okap wyciągowy

Najnowsze instrukcje dla Okap wyciągowy

Silverline PRW 800 Instrukcja

15 Stycznia 2025

Silverline STW 600 C Instrukcja

15 Stycznia 2025

CATA F 2260 X Instrukcja

15 Stycznia 2025

Bosch DWK09M760 Instrukcja

15 Stycznia 2025

Zanussi ZHC 1000 x Instrukcja

15 Stycznia 2025

AEG-Electrolux X69453MVO Instrukcja

15 Stycznia 2025

Beko CWB 9441 Instrukcja

15 Stycznia 2025

Bosch DWB097A51 Instrukcja

15 Stycznia 2025

Elica EST630SS Instrukcja

15 Stycznia 2025

Atag WS90211EM Instrukcja

15 Stycznia 2025