Instrukcja obsługi Skytec Portable Soundset 10 inch MP3

Skytec Głośniki Portable Soundset 10 inch MP3

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Skytec Portable Soundset 10 inch MP3 (16 stron) w kategorii Głośniki. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/16
Portable Soundset 10” – MP3
170.117
USER MANUAL
HANDLEIDING
GEBRAUCHSANWEISUNG
ENGLISH 170.117
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Warning: To reduce the risk of fire or electric shock, do not expose this unit to rain or moisture.
The lightning flash with an arrowhead symbol within an equilateral triangle, is intended to alert the user to
the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature accompanying the product.
Do not place this unit on an unstable cart, stand or tripod, bracket or table. The unit may fall, causing
serious injury to a child or adult and serious damage to the unit. Use only with a cart, stand, tripod, bracket
or table recommended by the manufacturer or sold with the unit. Any mounting of the device on a wall or
ceiling should follow the manufacturer instructions and should use a mounting accessory recommended by
the manufacturer. An appliance and cart combination should be moved with care. Quick stops, excessive
force and uneven surfaces may cause the appliance and cart combination to overturn.
Read and follow all the safety and operating instructions before connecting or using this unit. Retain this
notice and the owners manual for future reference.
All warnings on the unit and in its operating instructions should be adhered to.
Do not use this unit near water; for example, near a bath tub, washbowl, kitchen sink, laundry tub, in a wet
basement or near a swimming pool.
The unit should be installed so that its location or position does not interfere with its proper ventilation. For
example, it should not be situated on a bed, sofa, rug or similar surface that may block the ventilation
openings; or placed in a built-in installation, such as a bookcase or cabinet, that may impede the flow of air
through its ventilation openings.
The unit should be situated from heat sources such as radiators, heat registers, stoves or other devices
(including amplifiers) that produce heat.
The unit should be connected to a power supply outlet only of the voltage and frequency marked on its rear
panel.
The power supply cord should be routed so that it is not likely to be walked on or pinched, especially near
the plug, convenience receptacles, or where the cord exits from the unit.
Unplug the unit from the wall outlet before cleaning. Never use benzene, thinner or other solvents for
cleaning. Use only a soft damp cloth.
The power supply cord of the unit should be unplugged from the wall outlet when it is to be unused for a
long period of time.
Care should be taken so that objects do not fall, and liquids are not spilled into the enclosure through any
openings.
This unit should be serviced by qualified service personnel when: The power cord or the plug has been
damaged; Objects have fallen, or liquid has been spilled into the unit; The unit has been exposed to rain or
liquids of any kind; The unit does not appear to operate normally or exhibits a marked change in
performance; The device has been dropped or the enclosure damaged.
DO NOT ATTEMPT SERVICING OF THIS UNIT YOURSELF. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL
Upon completion of any servicing or repairs, request the service shops assurance that only Factory Authorized
Replacement Parts with the same characteristics as the original parts have been used and that the routine safety
checks have been performed to guarantee that the equipment is in safe operating condition.
REPLACEMENT WITH UNAUTHORIZED PARTS MAY RESULT IN FIRE
GETTING STARTED
1. Remove speakers, power cable and the speaker cables from the carton.
2. Detach the modules from the speakers. By pressing and sliding the button on the top of the speakers you will
release the module from the speaker. All that is required is a little lift on the module once the button is pressed.
3. If you have purchased speaker stands, you can place the speakers on the stands utilizing the pole mount adaptor
built into the speaker cabinets. Once the speaker is on the pole, tighten the set screw to snug the speaker to the
pole.
4. Connect the Mixer Module to the Speakers
On the right side of the mixer you will notice two ¼" phone jacks – these are your speaker output jacks. Take the
speaker cables and connect them from these jacks to the jacks on the back of the speakers.
5) Connecting the AC Power Cable
Connect the female end of the power cable to the mixer and plug the male end into the wall socket or extension
cord. Turn the “MASTER VOLUME” control to “0”. Now turn the power switch to the “on” position. You should see
the “POWER” indicator illuminated. At this point you are ready to bring in an audio signal and hear the signal
amplified by the system., Brass or
Strings
EFFECT MENU
Getting Acquainted with the Powered Mixer
This part of the system houses the mixing board and power amplifier. You will connect all of the microphones,
musical instruments, external sound sources (like MP3 or CD players), headphones in addition to any recording
devices or additional speakers like a personal monitor, subwoofer or “Front of House” feed.
The Basics
While it looks complicated, the mixing board is actually a very simple device. A “mixing board” brings audio sources
“in” (through the inputs) and routes the signal to the outputs (MASTER VOLUME/SPEAKER OUTPUTS or
MONITOR OUTPUTS)). The mixer controls enable the user to affect the tone and/or volume in addition to routing
the signal and adding effects to individual input sources. The abundance of knobs is simply due to the repetitive
nature of the design.
AUDIO INPUTS
The system has 8 inputs: 4 mono inputs and 2 stereo inputs.
All of the inputs will route to the speakers and to the MONITOR OUTPUT SECTION.
MONO MIC/LINE INPUTS
There are 4 identical input strips comprised of a “peak LED”, a combination input connector, MIC/LINE selector,
Treble and Bass controls, an Effect and a channel volume control.


Specyfikacje produktu

Marka: Skytec
Kategoria: Głośniki
Model: Portable Soundset 10 inch MP3

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Skytec Portable Soundset 10 inch MP3, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Głośniki Skytec

Instrukcje Głośniki

Najnowsze instrukcje dla Głośniki

Steren

Steren SPK-1100BL Instrukcja

15 Października 2024
Pyle

Pyle PBMSPG6 Instrukcja

14 Października 2024
Marshall

Marshall Tufton Instrukcja

14 Października 2024
Sunstech

Sunstech SPUBT780 Instrukcja

14 Października 2024
Marquant

Marquant 002-222 Instrukcja

13 Października 2024
Naxa

Naxa NAS-3060 Instrukcja

13 Października 2024
Philips

Philips SPA1301 Instrukcja

13 Października 2024