Instrukcja obsługi Skytec DMX FOG MACHINE
Skytec
Muzyka na imprezę DJ-ską
DMX FOG MACHINE
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Skytec DMX FOG MACHINE (15 stron) w kategorii Muzyka na imprezę DJ-ską. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/15
DMX FOG MACHINE
160.446
INSTRUCTION MANUAL
HANDLEIDING
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
GB
WARNING
- The fog machine must be placed at least 100 cm away from inflammable materials such
as curtains, books, etc. Make sure that the housing cannot be touched by accident.
- For indoor use only in dry rooms.
- During installation, nobody should stand beneath the mounting area.
- Prior to the first use, have the unit checked by a qualified person.
- The unit contains voltage carrying parts. DO NOT open the unit.
- Unplug the unit from the mains prior to repairs, maintenance and replacement of the
lamp.
- Never plug or unplug the unit with wet hands.
- If the plug and/or mains lead are damaged, they need to be repaired by a qualified
technician.
- If the unit is damaged to an extent that you can see internal parts, do not plug the unit
into a mains outlet.
- Only connect this unit to an earthed mains outlet of 230Vac/50Hz and 10-16A.
- Always unplug the unit during a thunderstorm or when it is not in use.
- If the unit has not been used for a longer period of time, condensation can occur inside
the housing. Please let the unit reach room temperature prior to use.
- When you unplug the unit from the mains always pull the plug, never the lead.
- In order to prevent dropping of the unit, a safety fastening needs to be installed. This can
be a solid chain, a steel cable, etc. which has to be fastened separately from the
mounting bracket.
- The supplied bracket is the main fixing and must be used to solidly mount the light effect.
- In order to avoid accidents in public premises, the local legal requirements and safety
regulations/warnings must be fulfilled.
- Keep out of the reach of children.
- Every fog machine may produce a small quantity of fog during use and after having it
switched on or off.
- Use this fog machine only in well ventilated places.
- Use the fog machine only for short periods of time. It is not meant for continuous use.
SAFETY RECOMMENDATIONS
Always connect the fog machine to a wall outlet or an earthed mains lead! Please note: the
mains lead should only be replaced by an equivalent lead supplied by SkyTronic.
Be careful when filling the tank. Unplug the unit from the mains first! Open the tank and fill it
by means of a suitable funnel.
Only use SkyTec fog fluid. This fluid is environmental friendly, biodegradable and, if properly
used, leaves no residues.
Do not obstruct the openings on top of the housing in order to ensure a proper cooling. The
heat generated by the heating element must be dissipated. Do not place any objects on the
fog machine. Do not close rooms in which this fog machine is used. A supervising person
must always be present.
Place the unit in such a way that there is always more than 5m free space in front of it
otherwise there is a risk that people get in panic because they lose orientation.
The smoke must not remain longer than 5 minutes in a room with a sight of less than 10m.
INSTALLATION AND USE
Unpack the unit. Do not connect the mains lead of the remote control yet. Connect the lead
of the remote control fitted with the 5-pin connector to the rear panel of the fog machine or if
the unit will be DMX controlled, connect the DMX lead fitted with the 3-pin XLR connector.
Open the ice tank by removing the 2 screws on the front/top side and open the cover of the
top side. Fill the ice tank with normal ice cubes or dry ice. You can fill in up to 8 kg of ice
cubes. Close the ice tank properly after filling.
OPEN THE COVER ONLY WHEN THE UNIT IS SWITCHED OFF!!
Fill the fog fluid tank via a suitable funnel. Then plug the unit into a mains outlet. This
switches the heating element automatically on. The pre-heating time lasts for about 12
minutes depending on the room temperature. Once the temperature is reached, the
thermostat clicks and the unit is ready for use. The fog machine can produce continuously
fog for about 2 ½ minutes. After this period, the fog generator is cooled down and the
thermostat switches off. The unit needs to heat up again for a few minutes. If you produce
fog at intervals, the temperature remains at the right level and the thermostat doesn’t switch
off.
EVACUATION OF MELT WATER
After use, you need to evacuate the melt water. There are 2 ways of proceeding:
1. Tilt the unit slightly forwards and open the tap on the front panel. Collect the water in
a basin.
2. Evacuate the melt water via the built-in pump. Connect a hose to the output at the
rear side. Switch the pump on via the switch on the rear panel of the unit.
MAKE SURE THAT THE WATER IS EVACUATED EVERY DAY
OPERATION VIA THE REMOTE CONTROL
First of all, switch the unit off before you plug or unplug the remote control.
Connect the remote control to the fog machine via the 5-pin DIN connector.
Check if all dip-switches on the rear panel are set to OFF. Switch the fog
machine on via the main switch at the rear panel. Switch the remote control on
or off via the START switch (7). When the remote control is connected, the red
LED (4) lights up.
Once the fog machine has reached the right temperature, the green LED (5)
will light up. The unit can be controlled manually via the MANUAL button (8).
Switch the timer function on via the TIMER switch (6). When this function is
switched on, the yellow LED (3) lights up. When the remote control is in timer mode, the
intervals and the duration of the fog production can be set via the potmeters 1 & 2.
CONTINUAL (1) sets the duration of the fog production between 0.5 & 10 seconds.
INTERVAL (2) sets the interval time between two fog productions between 15 & 240
seconds.
DMX CONTROLLED OPERATION
The fog/ice machine features a built-in DMX control which allows to incorporate the unit into
a DMX circuit. Select the start address via the dip switches on the rear panel (switch 1 on =
address 1, 2 on = address 2, 3 on = address 4, etc.) The unit has 1 DMX channel. You can
set the output volume between 0 & 100%. The interval functions, etc. can be programmed
via a DMX controller.
SWITCHING OFF
Switch the unit off by unplugging it from the mains. Otherwise the 1000W heating element
continues to draw current.
Specyfikacje produktu
| Marka: | Skytec |
| Kategoria: | Muzyka na imprezę DJ-ską |
| Model: | DMX FOG MACHINE |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Skytec DMX FOG MACHINE, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Muzyka na imprezę DJ-ską Skytec
26 Września 2024
26 Września 2024
26 Września 2024
26 Września 2024
26 Września 2024
25 Września 2024
25 Września 2024
25 Września 2024
Instrukcje Muzyka na imprezę DJ-ską
- Muzyka na imprezę DJ-ską Pioneer
- Muzyka na imprezę DJ-ską Vonyx
- Muzyka na imprezę DJ-ską ION
- Muzyka na imprezę DJ-ską Gemini
- Muzyka na imprezę DJ-ską Atomix
- Muzyka na imprezę DJ-ską Envivo
- Muzyka na imprezę DJ-ską Hercules
- Muzyka na imprezę DJ-ską US Blaster
- Muzyka na imprezę DJ-ską Serato
- Muzyka na imprezę DJ-ską Koden
Najnowsze instrukcje dla Muzyka na imprezę DJ-ską
28 Września 2024
26 Września 2024
26 Września 2024
26 Września 2024
25 Września 2024
24 Września 2024
24 Września 2024
23 Września 2024
22 Września 2024
21 Września 2024