Instrukcja obsługi SIIG CE-MT0612-S1
SIIG
Flat panel steun
CE-MT0612-S1
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla SIIG CE-MT0612-S1 (8 stron) w kategorii Flat panel steun. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/8
04-0528A
Low Profile Universal Mount - 32" to 60"
IMPORTANT: If you don't understand the installation instructions, please consult an installation
specialist
Fixed LCD/TFT TV Wall Mount
Material: 2.0mm Cold Rolled Steel Plate
TV Size: 32-60"
Max load capacity:165 lbs/75 kgs
Installation Instructions
Wall distance: 30mm/1.2"
Bubble level system included
Universal Mounting Pattern
A G
B H
C I
D J
E K
F L
M
(×4) M8 concrete anchor
(×4) M4×35 screw (×6) M8 Washer
(×4) M8 Spacer
(×4) M8×35 screw
The wall structure must be capable of supporting at least the maximum load capacity as indicated. If not, the wall must be
reinforced. Proper installation procedure by yourself or a qualified service technician, as outlined in the installation
instructions, must be adhered to. Failure to do so could result in serious personal injury.
Do not install near heater, fireplace, air conditioning, in direct sunlight, or any other heat producing source. Failure to do so
may result in damage to the display and could increase the risk of fire.
(×4) M4×12 screw
When mounting to a wall that contains wood studs, confirm dead center of the wood stud prior to installation, it is
recommended that the wood studs be a minimum of 16" apart.
(×4) M6×16 screw (×6) Bolt
(×4) M8×16 screw
INSTALLATION AND OPERATING INSTRUCTIONS
(×4) M6×35 screw
Caution
Hardware kit:
It is recommended that two people perform the installation. Injury and/or damage can result from dropping or mishandling
the display.
CAUTION: The maximum load capacity is 165 lbs. Use with products exceeding the maximum load capacity may cause
serious injury. See apparatus instructions.
(×4) M8/M6/M5 Washer
(×4) M4×16 screw
(×4) M5×16 screw
Do not install on a structure that is prone to vibration, movement or chance of impact. Failure to do so could result in
damage to the display and/or damage to the mounting surface.
Recommended mounting surfaces: wood stud and solid-flat concrete. If the mount is to be installed on any surface other
than wood studs, use suitable hardware (not included but commercially available).
Prior to the installation of this product, the installation instructions should be read and completely understood. The
installation instructions must be read to prevent personal injury and property damage. Keep these installation instructions
in an easily accessible location for future reference.
1
2
3
4
a) Wood Stud Installation
3
4
5
6
7
8
Stud finder for drywall installation
5/16" Socket and Wrench
Electric drill and 5/16" (8mm) masonry bit for concrete/brick installation
Note: Please ensure that the bubble level is mounted on the wall plate prior to mounting the wall plate.
Phillips head screw driver
CAUTION: Do not over-tighten bolts-doing so many cause unnecessary damage to the wall. Avoid excessive torque.
Mark the right (upper and lower) and the left (upper and lower) positions
of the small horizontalslots that are in alignment with the studs (figure 1
-
b).
CAUTION: Do not release the wall plate until it is properly mounted and secured to the wall.
Tools Required:
You should mark four positions total.
With the help of an assistant, and using the bubble level to ensure the
wall plate is level, position the wall plate against the wall in the desired
mounting location.
2
1
NOTE: When mounting to wood studs, the two wood studs must be a minimum of 16" apart.
Step1: Wall Plate Installation
Place the wall plate against the wall and line up the mounting slots with the drilled holes. Check the bubble level to verify
that the wall plate is level.
For each location, insert a lag bolt (J) and washer (L) into the wall
Tighten the bolt with an open ended socket wrench by turning clockwise until tight.
Use a high-quality electronic stud finder (commercially available) to
locate dead center of two studs and mark their locations with a pencil
(figure 1-a).
Next, pre-drill a 1/4" hole to a depth of 2" in the wall stud at each
marked location.
Specyfikacje produktu
Marka: | SIIG |
Kategoria: | Flat panel steun |
Model: | CE-MT0612-S1 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z SIIG CE-MT0612-S1, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Flat panel steun SIIG
3 Października 2024
Instrukcje Flat panel steun
- Flat panel steun Samsung
- Flat panel steun Sven
- Flat panel steun Iiyama
- Flat panel steun HP
- Flat panel steun Sanus
- Flat panel steun Icy Box
- Flat panel steun My Wall
- Flat panel steun V7
- Flat panel steun Ultimate
- Flat panel steun Digitus
- Flat panel steun One For All
- Flat panel steun Pyle
- Flat panel steun CTA Digital
- Flat panel steun Crimson
- Flat panel steun Mount-It!
- Flat panel steun Ewent
- Flat panel steun Chief
- Flat panel steun NEC
- Flat panel steun Vision
- Flat panel steun Vogel's
- Flat panel steun Abus
- Flat panel steun Rocstor
- Flat panel steun Gabor
- Flat panel steun 3M
- Flat panel steun Hitachi
- Flat panel steun GPX
- Flat panel steun Newstar
- Flat panel steun Speaka
- Flat panel steun Acco
- Flat panel steun Reflecta
- Flat panel steun Kensington
- Flat panel steun Techly
- Flat panel steun Da-Lite
- Flat panel steun Luxor
- Flat panel steun Steren
- Flat panel steun Barkan
- Flat panel steun Atlantic
- Flat panel steun Konig
- Flat panel steun HQ
- Flat panel steun BakkerElkhuizen
- Flat panel steun Peerless
- Flat panel steun SMS Smart Media Solutions
- Flat panel steun Proaim
- Flat panel steun Monoprice
- Flat panel steun Ergotron
- Flat panel steun Atdec
- Flat panel steun Multibrackets
- Flat panel steun B-tech
- Flat panel steun Kogan
- Flat panel steun Premier Mounts
- Flat panel steun Cabstone
- Flat panel steun SmartMetals
- Flat panel steun Zaor
- Flat panel steun Avteq
- Flat panel steun LTN Technologies
- Flat panel steun Helder
Najnowsze instrukcje dla Flat panel steun
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024