Instrukcja obsługi SII SLP650SE

SII drukarka etykiet SLP650SE

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla SII SLP650SE (27 stron) w kategorii drukarka etykiet. Ta instrukcja była pomocna dla 16 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/27

Smart Label Printers

User's Guide

Models 620, 650, and 650SE

U00128837201

For Windows® XP, Server 2003, Vista and Windows 7

or Mac OS® X 10.5 or later.

Smart Label Printers® Series

Smart Label Printers User's Guide Models 620, 650, and 650SE

U00128837200 November 2012

U00128837201 February 2013

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

 Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by Seiko Instruments could void the user's authority to

operate the equipment.

Applicable EC Directives and Standards

Directive Title

2004/108/EC EC Electromagnetic Compatibility Directive

2006/95/EC EC Low Voltage Directive

2011/65/EU Restriction of the ubstances (RoHS) Directive use of certain hazardous s

2009/125/EC Directive on Eco-Design of Energy-related Products

Standards Title

EMC EN55022 class B

EN61000-3-2, EN61000-3-3

EN55024

LVD EN60950-1

For use in Turkey

Complies with Electrical and Electronic Equipment Directive.

Türkiye' deki Kullanı ıc lar için

EEE Yönetmeliğine Uygundur.

reproduced, stored in a retrieval system, or transmitted, in any form, or by any means, electronic,

mechanical, photocopying, recording, or otherwise without the prior written permission of Seiko

Instruments Inc. No patent liability is assumed with respect to the use of information contained herein.

While every precaution has been taken in the preparation of this publication, Seiko Instruments USA Inc.

assumes no responsibility for errors or omissions. Nor is any liability assumed for damages resulting

from the use of information contained herein. Further, this publication and features described herein are

subject to change without notice.

Trademark Information

SII and the SII logo are registered trademarks of Seiko Instruments Inc. Smart Label Printer is a

registered trademark and SmartLabels, SmartCapture, SmartCopy and Smart Label Icons are

trademarks of Seiko Instruments USA Inc.

Other brand and product names are trademarks or registered trademarks of their respective holders.

Installation

For best performance, we recommend that you install your printer on a flat surface in a location that

satisfies the following environmental conditions:

 Not subject to vibration

 Not exposed to direct sunlight

 Dust-free

 Condensation-free

 Temperatures: 59°F to 95°F (15°C to 35°C)

 Humidity: 30%RH to 80%RH (non-condensing)

ABOUT THIS GUIDE

As you'll soon realize, the Smart Label Printer is easy to set up and use. Chances are, once you've read

what you need to know in order to get going, you won't have to use this guide except as a quick reminder

or a reference.

This guide will help you set up your SLP 620, 650, and 650SE, install the software, and use your SLP.

In writing this guide we assume that you are familiar with common operations using Microsoft Windows®

XP, Server 2003, Vista or Windows 7 on a Windows compatible PC, or Mac OS® X 10.5 or later on an

Apple Macintosh computer.

This guide has six sections for easy reference:

Introduction, provides some general information about the SLP 620, 650, and 650SE as well as the

Smart Label program.

Getting Started, provides instructions for connecting the SLP 620, 650, and 650SE to your

Windows-compatible PC or Mac, and loading labels into the printer. It also describes how to use on-line

help.

Changing Labels and Printer Care, provides information for replacing a label roll and taking care of

your SLP.

Specifications, provides SLP 620, 650 and, 650SE specifications.

Technical Support and Service, provides technical support and service information.

Ordering Labels and Parts, provides information for ordering SmartLabels, replacement parts, and

accessories.

INTRODUCTION

About Your Smart Label Printer

The Smart Label Printer is the best way to instantly print one-at-a-time labels. Direct thermal printing

technology does not use ink, toner or ribbon, just labels. The SLP produces fast, laser quality output on a

variety of label sizes with the ability to print text, graphics, POSTNET codes and barcodes.

With the wide variety of available SmartLabels, you can use your SLP to create labels for just about

anything. Here are some examples:

・・Envelope labels Barcode labels

・・File folder labels Business/Appointment Card

・Video Tape ・Name badge labels

・Security Voucher ・CD or DVD labels

・・Shipping labels Jewelry labels

・Storage container labels ・Binder labels

・・Notebook labels Shelf labels

・Videocassette labels

Software Features

The Smart Label program provides a rich set of features to simplify your labeling needs.

 WYSIWYG editor displays labels as they will print.

 Prints in background so you can work with other applications while labels are printing. Print

labels one at a time or whole mailing lists.

 Object-oriented user interface makes it easy to include text, pictures, barcodes, etc. on your

label.

 Mixed text possible within each text object—different font types, sizes and styles

(bold/italic/underline) can be included on a single line.

 Shrink-to-fit and word wrap ensure that addresses and other text fit on the label.

 Built-in database to save labels and formats in user-definable database categories.

 Find feature makes it easy to locate saved labels by label name, database field or words within

the label.

 Contact-based records updated automatically from label addresses.

GETTING STARTED

What You Need

In order to use your SLP and software, you need to have the following:

PC Users:

 Windows XP, Server 2003, Vista or Windows 7

 IBM® PC or compatible using 233MHz or higher Pentium-compatible CPU

 Minimum 64MB RAM, 128MB recommended

 1.5GB hard disk space

 USB port or RS232C serial port

 CD-ROM or DVD drive

Mac Users:

 Mac OS X v10.5 or later

 PowerPC® G4 (867MHz or higher), G5, or Intel® processor

 Minimum 512MB RAM

 Minimum 9GB hard disk space

 USB port

 DVD drive

A Word about Labels

For best results we recommend the use of Seiko Instruments SmartLabels. Other brands may not be

engineered to provide optimum, trouble-free results with your SLP; they may not work with your printer or

they may damage it and void your warranty.

SmartLabels are available in a wide variety of sizes and colors to properly label almost anything.

The SmartLabels have a mark on the backing of each label that the SLP 620, 650, and 650SE uses for

top of label alignment. Check to be sure the labels have this mark before loading them into the SLP.

Sensor mark

Note: Older SmartLabels did not have this mark. Be sure that the SLP 620, 650, and 650SE are listed as

supported printers on the SmartLabels package.

Caring for Labels

The labels are sensitive to heat, moisture, and light. With this in mind:

 Store labels in a cool, dry place.

 Do not scratch or rub labels with a hard object.

 Do not expose labels to high heat or direct light for an extended period of time.

 Keep organic solvents away from labels.

Mark

Installing the SLP 620, 650, or 650SE

Here, you'll find out how to unpack and set up your new SLP. As part of the setup process, you'll load a

roll of standard address labels and run a quick test.

Unpacking the SLP

Carefully remove the printer and its components from the box. It's a good idea to save the box and

packing materials in case you need to store or ship the printer. Accessories vary depending on the

package.

 A Smart Label Printer (SLP 620, 650, or 650SE)

 Safety Precautions

(Accessories)

 Smart Label software with User's Guide

 USB cable

 Serial cable

 AC adapter (PW-B0625-W1-U, PW-B0625-W1-E, PW-B0625-W1-B, PW-B0625-W1-A,

PW-B1230-W1-U, PW-B1230-W1-E, PW-B1230-W1-B, PW-B1230-W1-A)

 Starter roll of SmartLabels

 Quick Start Guide

A Smart Label Printer Safety Precautions

Quick Start

Smart Labels

Smart Label Software

USB Cable

AC Adapter

Serial Cable

SmartLabels

USB Cable

AC Adapter

A Smart Label Printer

Quick Start Guide CD-ROM

Safety Precautions

Installing the Software

Installing the Smart Label Program for MacOS X

1． Insert the Smart Label CD. If the installer does not appear automatically, double-click the CD on your

desktop or in the left pane of a new Finder window.

2． Double-click the file SIISmartLabelPrinter.mpkg. The installer will appear. Follow the on-screen

instructions.

3． Mac OS X 10.5 or later will automatically set up your printer, once the SLP is connected.

Installing the Smart Label Program for Windows

1． Insert the Smart Label CD. The installation wizard starts automatically on most systems. If the

introductory screen doesn't appear after a few seconds, do the following:

2． Click the Windows Start button then point to Settings and choose Control Panel.

3． Double-click Add/Remove Programs then click the Install button. Follow the install wizard to assist

with installation.

Please note: If your printer is not recognized or all label templates do not appear, you will need to set-up

your printer within the SLP printer software. Please see "Setting up the Printer".

Connecting the SLP to a Power Outlet

1． Connect the supplied AC adapter to the back of the SLP and to a power outlet.

DC IN

2． The printer powers on automatically when connected to AC power. The Status Light will flash if no

labels are loaded in the printer.

Form Feed button

Status light

Power button

Form Feed Button

Power Button

Status Light

Setting up the Printer

If the printer is not recognized using the installation wizard, you will need to set up your printer manually.

To do so, follow these steps:

Prepare the Roll of Labels

1． Open the Smart Label printer software.

2． Under the Label pull-down menu, select Printer Set-up.

3． Select Add a printer.

4． Select how your printer is connected and click Done.

Loading a Roll of Labels

Prepare the Roll of Labels

1． Remove the sticker from the beginning of the roll of labels.

Note: Make sure there is a black mark on the label backing as shown in

"A WORD ABOUT LABELS".

2． If necessary, cut between the labels to create a "leader".

Roll Waste Roll

Cut here

Prepared end

If the end of the roll is not prepar between the labels leaving as much backing as ed as shown above, cut

possible on the end of the roll to act as a leader.

3． Remove the Spindle from the SLP and insert the label roll into the Spindle.

4． Insert the labels and Spindle into the SLP. Adjust the guides to fit the labels as shown below.

Label guides

SLP provides three types of labels which have different paper width. Insert each label into

positions shown in the figures below.

5． Insert the free end of the label roll, label side down, into the paper inlet slot. Push the label stock into

the paper inlet slot until you feel a slight resistance. Continue pushing gently. The SLP automatically

feeds the labels through and aligns the end in the exit slot.

If the label end doesn't appear through the exit slot:

Press and release the Form Feed Button to advance the labels.

Label Guides

6． Close the Roll Cover. At the time, be careful not to close the Roll Cover on your fingers.

Testing the Printer

A quick test lets you know your printer is operating properly and that the labels are loaded correctly.

Testing the SLP 620, 650, and 650SE

1． Press and hold the Power Button for 2 seconds to turn the printer standby.

2． Press and hold the Form Feed Button and then press the Power Button. The green Status Light will

begin to flash. Do not release the Form Feed Button.

3． To print the serial number and firmware version:

 While holding the Form Feed Button, press and release the Power Button once, and release

the Form Feed Button.

4． To print the density test:

 While holding the Form Feed Button, press and release the Power Button twice, and release

the Form Feed Button.

Specyfikacje produktu

Marka:	SII
Kategoria:	drukarka etykiet
Model:	SLP650SE

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z SII SLP650SE, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje drukarka etykiet SII

SII SLP650SE Instrukcja

2 Października 2024

SII SLP620 Instrukcja

2 Października 2024

SII SLP650 Instrukcja

2 Października 2024

Instrukcje drukarka etykiet

Najnowsze instrukcje dla drukarka etykiet

Star Micronics TUP592-24 Instrukcja

9 Marca 2025

Godex EZ2250i Instrukcja

7 Marca 2025

Kroy L4350C Instrukcja

3 Marca 2025

Datamax O'Neil I-4606 Instrukcja

17 Lutego 2025

Datamax O'Neil Ex2 RL4 Instrukcja

17 Lutego 2025

Brother PJ-623 Instrukcja

6 Lutego 2025

Zebra ZD621d Instrukcja

28 Stycznia 2025

Brother PT-H101GB Instrukcja

13 Stycznia 2025

Brother P-Touch PT-1290DT Instrukcja

13 Stycznia 2025

Zebra ZQ320 Instrukcja

12 Stycznia 2025