Instrukcja obsługi Signature Hardware Bennett 433107

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Signature Hardware Bennett 433107 (2 stron) w kategorii Niet gecategoriseerd. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/2
1Bennett Kitchen Faucet Installation Instructions
INSTALLATION
BENNETT KITCHEN FAUCET INSTALLATION
BEFORE YOU BEGIN
We recommend consulting a professional if you are
unfamiliar with installing plumbing fixtures. Signature
Hardware accepts no liability for any damage to the
faucet, plumbing, sink, counter top, or for personal injury
during installation.
Observe all local plumbing and building codes.
Unpack and inspect the faucet for shipping damage. If
any damage is found, contact our Customer Relations
team at 1-8 -55 71 18005- .
Note: Make sure to winterize your outdoor faucet
before cold weather arrives to prevent burst pipes and
protect the faucet’s hardware.
*not included
TOOLS AND MATERIALS:
GETTING STARTED
Ensure that you have gathered all the required
materials that are needed for the installation.
For these instructions, it is assumed that the old
faucet has been completely removed and any
necessary repairs or modifications to the water
supply have been completed.
Plumbers
Tape*
Thread
Sealant*
Adjustable
Wrench*
Phillips
Screwdriver*
Small
Bucket*
Basin
Wrench*
2. Remove the lock nut, rubber washer, and metal
washer from the faucet body. Insert the faucet through
the mounting hole in your counter top.
1. Ensure that the water supply below your sink is
completely shut off by turning the shutoff valves all the
way to the right.
Tip: Place a small bucket below your workspace to
catch any water that may drip during the installation
process.
OFF
SKU(s): 433107, 433135
1.855.715.18001.855.715.1800
Bennett Kitchen Faucet Installation Instructions
BENNETT KITCHEN FAUCET INSTALLATION
2
5. Once installation is complete, turn the main water
supply back on from underneath your sink. Check for
any leaks underneath.
6. Remove the aerator from the spout. Turn the faucet
on and allow the water to flow for approximately 60
seconds. Ensure that there are no leaks, and that both
hot and cold water are running properly. Divert water to
the sprayer setting and allow it to flow for another 60
seconds.
3. From beneath the sink, slide the rubber washer and
metal washer back onto the faucet body. Thread the
lock nut back onto the shank and hand tighten. Finish
securing the faucet by tightening the two screws
attached to the lock nut with a Phillip’s screwdriver.
Note: For thin mounting surfaces, use the provided
plastic support. The support should slide on first,
before the rubber gasket.
4. Apply plumber’s tape or thread sealant to the
threading on each of the faucet’s water lines, and
connect the main water hoses to the faucet. Ensure
that you are connecting the hot and cold lines appro-
priately.
ON
1.855.715.18001.855.715.1800

Specyfikacje produktu

Marka: Signature Hardware
Kategoria: Niet gecategoriseerd
Model: Bennett 433107

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Signature Hardware Bennett 433107, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Niet gecategoriseerd Signature Hardware

Instrukcje Niet gecategoriseerd

Najnowsze instrukcje dla Niet gecategoriseerd

Teka

Teka FS 602 4GG Instrukcja

9 Października 2024
Teka

Teka FS 902 5GG Instrukcja

9 Października 2024
Neewer

Neewer X14 III Instrukcja

9 Października 2024
Teka

Teka TR 750 Instrukcja

9 Października 2024
Teka

Teka TR 550 Instrukcja

9 Października 2024
Teka

Teka RSL 41150 BU Instrukcja

9 Października 2024
Danby

Danby WFF176W Instrukcja

9 Października 2024
Bartscher

Bartscher 500387 Instrukcja

9 Października 2024
Hartke

Hartke Chorus HC33 Instrukcja

9 Października 2024