Instrukcja obsługi Sierra Designs Moken 6

Sierra Designs namiot Moken 6

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Sierra Designs Moken 6 (2 stron) w kategorii namiot. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

SIERRA DESIGNS 2011 Cherry Street, Unit 202 Louisville, CO 80027 Phone: 303-262-3050 Fax: 303-262-3051 Toll Free: 800-635-0461

insert

incorrect

correct

Figure 3: Hub Hook with Spider Hub

S I E R R A D E S I G N S

Figure 5: Clip Loc

MOKEN 6

Your Sierra Designs

MOKEN 6 tent is

very easy to pitch and

maintain. Follow these in-

structions to pitch your tent

quickly, safely and easily.

MOKEN 6 TENT CONTENTS

Tent Body & Rainﬂy: 1 Line Tighteners: 6

Sleeping Rooms: 2 Pitching Instructions: 1

Tent Poles: 4 Pole Sack: 1

Tent Stakes: 12 Stake Sack: 1

Guy Cords: 6

* Sierra Designs tents include stakes for pitching the body and

ﬂy under normal conditions. Additional stakes may be required

in severe conditions.

Figure 2: Correct Pole Assembly

Figure 1: Main Pole with Spider Hub

Figure 4: Tent body (top view)

Figure 6: Toggle/Ring

First Pitch

In order to familiarize yourself with your new tent, we sug-

gest that you grab a friend or relative and do a “test pitch”

before you enjoy your outdoor adventure.

Select a Site

Pitch the tent on a level area that is protected from wind

and shaded from the sun, if possible. It also important that

the campsite drains well, in case of rain. Clear the area of

debris such as sharp stones and sticks that might abrade or

puncture the tent ﬂoor.

Assemble the Poles

The comes with 3 poles. The main pole is connect-Moken 6

ed via the “Spider Hub” (Figure 1) the remaining two poles

are of equal length with slight pre bends in them. Coming

from the center of the hub will be 4 longer poles and two

short poles. Assemble this pole ﬁrst by carefully unfolding

the shock corded sections and allowing them to slide together.

Do not snap the pole sections together, as this could damage

the poles. Make certain that the insert for each pole section is

fully inserted into the next pole section, as well as, the “Spider

Hub” (Figure 2). Failure to do so may cause the poles to break.

Once assembled place to the poles to the side.

Lay Out Tent Body

Unfold the tent body and lay ﬂat on the ground so that the

blue and grey rainﬂy is facing up. You will notice that the in-

ner tents and common room footprint are already attached to

the rainﬂy. By having these parts pre assembled it will make

the initial set-up of your much easier. Spread the tent Moken 6

out so that you are able to ﬁnd the “Hub Hook” (Figure 3).

This is located at the center of the tent (Figure 4, point M).

Once you have located the “Hub Hook” you will want to locate

the four navy blue stakeout loops (Figure 4, points A, B, G &

H). If you are pitching this tent by yourself we suggest that

you stake these four points down for an easier pitch.

Erect the Tent

Attach the “Hub Hook” to the loop on the underside of the

“Spider Hub” and that the two short poles are facing the tent

doors. Now, start with the end of the longer pole that is fac-

ing point A (Figure 4) and insert the pole tip into one of the

grommets. Follow this step for point G and then move to the

other side of the tent and repeat with points B & H. Once the

main pole structure is up attach the Swift Clips and Clip Locs

(do not attach bungee yet) along the A-H and B-G axis. You

now have two main body poles left. Each one of these poles are

SIERRA DESIGNS 2011 Cherry Street, Unit 202 Louisville, CO 80027 Phone: 303-262-3050 Fax: 303-262-3051 Toll Free: 800-635-0461

S I E R R A D E S I G N S

MOKEN 6

equal in length and have 2 pre bends in them, so it does not

matter which pole you use. The remaining two poles will need

to be threaded through external pole sleeves along the N-O and

P-Q axis (Figure 4). Once one of the poles has been threaded

through the pole sleeve insert the pole tip into the grommets

provided at points E & F or C & D. Repeat this step for the

remaining pole. Attach the Clip Locs at points N, O, P, &

Q to their corresponding pole intersections. Now attach the

bungee cordon the four Clip Locs by wrapping the bungee in

the direction crossing the open gate of the clip. Wrap the cord

around the intersection 2 to 4 times, depending on the desired

ﬁrmness, then, slide the cord into the groove on the backside

of the clip to keep it taut (Figure 5). Next, insert the pole tips

on the shorter poles and insert into the grommets provided at

points R & S (Figure 4). Lastly, stake out points I & J. You

will notice that at both points I & J, there will be two stake

loops. One is for the rainﬂy and one is for the inner sleeping

room, stake them both out to the same stake. Repeat this pro-

cess for points K & L.

Stake Out the Tent

If you have not already staked out all 12 stake out loops

(Figure 4, points A-L) we suggest you do so now. Once fully

staked out work your way around the tent and make any nec-

essary adjustments so that your tent has been pitched to its

desired tautness.

Sleeping Room Set-Up/Removal

Now that your Moken 6 is pitched and you have been able

to view it from the inside you will notice that you have two

sleeping rooms and a living area. You will also notice that the

two sleeping rooms are removable. By having these two rooms

removable it allows you various options for your Moken 6, such

as, both sleeping rooms in, 1 room in and 1 room out, or both

sleeping rooms removed. In order to remove the sleeping rooms

all you need to do is unhook the “Toggle/Ring” (Figure 6) sys-

tem and then unclip the “side-release” buckles on the ﬂoor.

Ventilate the Tent

You have various options for ventilating your Moken 6. The

most effective way is to utilize the roof vents, along with the

rainﬂy doors. You will notice that the roof in the main living

section of your tent has two ceiling vents that allow for ventila-

tion. In addition to the ceiling vents there are four additional

vents, 2 for each sleeping room. There are also two zip down

panels within the vestibule.

Specyfikacje produktu

Marka:	Sierra Designs
Kategoria:	namiot
Model:	Moken 6

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Sierra Designs Moken 6, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje namiot Sierra Designs

Sierra Designs Moken 6 Instrukcja

24 Września 2024

Sierra Designs Zeta 2 Tent Instrukcja

3 Lipca 2024

Instrukcje namiot

Najnowsze instrukcje dla namiot

SereneLife SLTET30 Instrukcja

9 Października 2024

Calima 46074 Instrukcja

9 Października 2024

SereneLife SLPTLB106 Instrukcja

9 Października 2024

SereneLife SLPTSR107 Instrukcja

9 Października 2024

SereneLife SLPTMR108 Instrukcja

9 Października 2024

SereneLife SLPTMLR109 Instrukcja

9 Października 2024

Ikea CIRKUSTÄLT 605.813.69 Instrukcja

8 Października 2024

Ikea CIRKUSTÄLT 205.813.66 Instrukcja

8 Października 2024

Ikea CIRKUSTÄLT 805.813.68 Instrukcja

8 Października 2024

Brunner Beyond Instrukcja

8 Października 2024