Instrukcja obsługi Siemens RDE100FP
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Siemens RDE100FP (4 stron) w kategorii termostat. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/4
1/4 s - - Operating Instruction CB1B1426en_01 / 2013 07 05 Siemens Building Technologies
s
I Operating nstructions
RDE100 FP
The RDE100FP rogrammer pis a with 3 "Fil Pilote" zones lectto se Comfort or Economy for different mode
zones at any time.
Note: - The Comfort setpoint must be set directly on each radiator’s thermostat
- T " he radiator’s operating mode must be set to "Automatic
1 Display
Stop mode
Confirmation
Auto Timer mode
F
Room temperature in
degrees Fahrenheit
View and set Auto Timer
Comfort mode
C
Room temperature in
degrees Celsius
Economy mode
Button lock activated
Escape Room temperature
Setting the weekday and
the time ayof d
Display of zone
Holiday mode setting Weekday 1 = Monday
Weekday 7 = Sunday
T ime of day
Timer bar
Morning: 12 hour format-
Afternoon: 12 hour format-
Current room
temperature
2 Change operating mode
3 Set
4 Ok
5 Decrease zone value
6 Increase zone value
Do you want to the time of day set and the weekday?
Set
Ok
+
–
Mode
!
Proceed as follows:
• Press Set and select
• Press Ok and the time of day flashes for setting
• Press + – or to set the time of day
• Press Ok to confirm
• W ; eekday flashes press + – or to select the weekday
• Press Ok to save
• Press M ode to exit or wait for the program to exit automatically
Note:
In the event of power failure followed by power restoration the time of day that the a , flashes means , which user
must adjust it repeat the steps from point 3 above. and
All others setting are saved.
Until the time , the program sends protection all available zones. setting made is commands to
Do you want to lock the buttons?
M Mode Press and hold ode for at least 7 seconds to activate a button lock. Repeat to unlock.
The unit operates normally when the buttons are locked, but changes cannot be made.
Do you want to set your Holiday mode?
Set
Ok
+
–
M ode
!
You can enable Holiday zone mode for all s .The radiator managed by the programmer controls the room
temperature with the rotection setpoint. P
• Press Set and select
• Press Ok to confirm
• Press + – or to set s m the number of days for holiday (0 = Holiday ode Off)
• Press Ok to save
• When Holiday mode is activated, the remaining days are displayed
Note:
If M ode e .is pressed while Holiday mode is , the function active is deactivated and th symbol disappears
Energy saving tips without loss of comfort
• T Select Auto imer mode during the heating period and set the time switch as desired
• - Select Economy or Holiday mode for longer periods of non occupancy and during the summer
2/4 s - - Operating Instruction CB1B1426en_01 / 2013 07 05 Siemens Building Technologies
Do you want to change the operating mode?
Mode
+
–
!
For each zone (1, 2 or 3), the unit allows you
to select Comfort, Economy or automatic
mode.
Press + – or z 3; , to select one 1, 2 or then
select the mode using the operating Mode
button.
Comfort mode is the permanent (24 h)
selection of Comfort. Select this operating
mode to maintain Comfort temperature the
without time switch during occupancy (e.g.
periods).
Economy mode is the permanent (24 h)
selection of Economy. Select this operating
mode to maintain Economy temperature the
without time switch (e.g. during the summer
when heating is is used forO )ff . It non-
occupancy periods when you want to
maintain the Economy temperature e.g. at (
night).
AUTO
In Auto Timer mode, the operating
modes (Comfort, Economy) are changed
automatically according to the time switch
settings.
Note:
Stop mode is a special mode when all
" " Fil Pilote stop signals are sent to all valid
and active zones. During Stop mode, you
can only do tasks, either 2 make parameter
settings or the weekday and set the of time
day. When Stop mode is enabled, the zone
number disappears.
You can enable the number of zones via
parameter settings (P18); the default value
is 3.
Do you want to enter your own time switch?
Option 1: Time switch with individual day settings
(P11=0)
Set
Ok
+
–
M ode
!
For the selected zone, you can select
Comfort or Economy mode 15 minute in -
steps throughout the day. The 0:00 to 24:00
hour time bar allow you to ses lect the
operating mode the respectivefor day(s).
Example:
0 6 12 24
18
1 2
Visible bars: Control to Comfort
temperature
Invisible bars: Control to Economy
temperature
When Auto imer mode is enabled, T
changeover between the operating modes is
automatic after the settings are saved.
Proceed as follows:
1) Press + – or to select the zone.
2 ) Press Set and select
AUTO
.
3 ) Press Ok to confirm.
4 T . ) ime switch for Mon (1) is displayed
5) Press + – or to select the day,
from Mon (1) to Sun (7).
6 ) Press O k to confirm the selection and
initiate time programming.
During programming:
7 ) Press Mode to select the operating
mode (Comfort or Economy) or
8) Press + – or to set the time 15 of day in -
minute teps operating s for the selected
mode.
9 ) Press Ok to save the time switch.
10) Repeat remaining days (if steps 5-9 for all
re or quired),
11) Press Mode or wait for the program to exit
automatically.
Note:
Repeat the above steps to program the
remaining zones.
3/4 s - - Operating Instruction CB1B1426en_01 / 2013 07 05 Siemens Building Technologies
Option 2: Time switch with the ttingssame 7 day se-
(P11=1)
Set
Ok
+
–
M ode
!
You can set that all the time switch so
settings apply to the 7 weekdays .
Example:
0 6 12 24
18
1 2
Visible bars: Control to Comfort
temperature
Invisible bars: Control to Economy
temperature
Proceed as follows:
1) Press + – or to select one.the z
2) Set the parameter (P11=1). Please refer
to section "Do you want to change
parameters".
3 ) Press Set and select
AUTO
.
4 ) Press Ok to confirm.
5 – ) Time switch for Mon (1) Sun (7) is
displayed.
6 ) Press Ok to initiate time programming.
During rogrammingp :
7 ) Press Mode to select the operating mode
(Comfort or Economy) or
8) Press + – or to set the time 15 of day in -
minute steps operating for the selected
mode.
9 . ) Press Ok to save the settings
10 to ) Press Mode or wait the program for
exit automatically.
Note:
Repeat the above steps to program the
remaining zones.
Information on the standard "F P " il ilote –
s etpoints
The RDE1001FP is a programmer to manage the used
operating modes.
The setpoints are managed by your electrical radiators or
heaters.
. Please refer respective Oto the perating Instructions
According to the standard:"F P " il ilote
The Comfort setpoint must be set directly on the
thermostat of electrical radiator or heater.the
The Economy setpoint is 3 °C below the Comfort
setpoint.
The edProtection setpoint is fix at 7 or 8 . °C
Option 3: Time switch with 5-2-day settings
(P11=2)
Set
Ok
+
–
M ode
!
You can set Monday Friday and Saturday - -
Sunday at the same time.
Example:
0 6 12 24
18
1 2
Visible bars: Control to Comfort
temperature
Invisible bars: Control to Economy
temperature
Proceed as follows:
1) Press + – or to select the zone.
2) Set the parameter (P11=2). Please refer
to section ou want to change "Do y
parameters?".
3) Press Set and select
AUTO
.
4) Press Ok to confirm.
5) Time switch for Mon – (1) Fri (5) is
displayed.
6) Press + – or to select Mon – (1) Fri (5) or
Sat Sun – (6) . (7)
7) Press Ok to confirm the selection and
initiate time programming.
During programming:
8) Press Mode to select the operating mode
(Comfort or Economy), or
9) Press + – or to set 15 the time of day in -
minute steps operating for the selected
mode.
10) Press to save the Ok settings.
11) Repeat step 10 for the other period if s 6-
necessary, otherwise
12) Press or wait for the program to Mode
exit automatically.
Note:
Repeat the above steps to program the
remaining zones.
Factory default for 7- t day ime switch
Default
value
Day/s Comfort mode Economy mode
Mo (1) –
Fr (5)
6:00 – 8:00 hr
17:00 – 22:00 hr
22:00 – 6:00 hr
8:00 – 17:00 hr
Sa (6) –
Su (7)
– – 7:00 22:00 hr 22:00 7:00 hr
Specyfikacje produktu
| Marka: | Siemens |
| Kategoria: | termostat |
| Model: | RDE100FP |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Siemens RDE100FP, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje termostat Siemens
15 Października 2024
7 Października 2024
5 Października 2024
4 Października 2024
3 Października 2024
1 Października 2024
1 Października 2024
30 Września 2024
29 Września 2024
29 Września 2024
Instrukcje termostat
- termostat AEG
- termostat TP-Link
- termostat Bosch
- termostat Ferroli
- termostat Nobo
- termostat Theben
- termostat Crestron
- termostat Nexa
- termostat Tesla
- termostat Fenix
- termostat Taurus
- termostat Eberle
- termostat Honeywell
- termostat Remeha
- termostat Truma
- termostat ORNO
- termostat Intergas
- termostat Vimar
- termostat Schneider
- termostat Techno Line
- termostat Emos
- termostat Buderus
- termostat Renkforce
- termostat Corbero
- termostat BaseTech
- termostat Viessmann
- termostat Trotec
- termostat Somfy
- termostat Tado
- termostat AVM
- termostat Homematic IP
- termostat Danfoss
- termostat Delta Dore
- termostat Vaillant
- termostat Devolo
- termostat Dimplex
- termostat Baxi
- termostat SPC
- termostat Atag
- termostat Westfalia
- termostat Remko
- termostat Oregon Scientific
- termostat Elro
- termostat Netatmo
- termostat Schwaiger
- termostat Junkers
- termostat Emerson
- termostat Vemer
- termostat Busch-Jaeger
- termostat Elektrobock
- termostat Hunter
- termostat Fibaro
- termostat Salus
- termostat EQ-3
- termostat Emko
- termostat Heatmiser
- termostat Avidsen
- termostat JUNG
- termostat Carrier
- termostat H-Tronic
- termostat EVE
- termostat Elgato
- termostat Wachendorff
- termostat Sygonix
- termostat De Dietrich
- termostat Müller
- termostat Profile
- termostat Nefit
- termostat Agpo Ferroli
- termostat Amfra
- termostat Itho
- termostat Devi
- termostat Stiebel Eltron
- termostat Elco
- termostat Magnum
- termostat Horstmann
- termostat Tylö
- termostat Oventrop
- termostat King
- termostat Arnold Rak
- termostat Nest
- termostat Itho-Daalderop
- termostat Hive
- termostat Saunier Duval
- termostat Seitron
- termostat Plieger
- termostat Aube
- termostat Zehnder
- termostat Bulex
- termostat UPM
- termostat Optima
- termostat AWB
- termostat Finder
- termostat Xavax
- termostat Fantini Cosmi
- termostat Orbis
- termostat Boneco
- termostat Grasslin
- termostat Gira
- termostat Wolf
- termostat HQ
- termostat Max
- termostat Eneco
- termostat Frico
- termostat Vasco
- termostat Radson
- termostat EQ3
- termostat Go Green
- termostat Landis Gyr
- termostat Weishaupt
- termostat ICY
- termostat HomeMatic
- termostat Mikoterm
- termostat Brink
- termostat Drayton
- termostat Oertli
- termostat Heatit
- termostat 2Heat
- termostat Bryant
- termostat Watts
- termostat Etherma
- termostat Emmeti
- termostat Enda
- termostat Eurotronic
- termostat Worcester-Bosch
- termostat Econo-Heat
- termostat VDH
- termostat PECO
- termostat EasyTemp
- termostat Tru Components
- termostat Easy Timer
- termostat Z-Wave
- termostat Hugo Muller
- termostat IMIT
- termostat Innogy
- termostat Wallair
- termostat Maico
- termostat Levica
- termostat HomePilot
- termostat Ouellet
- termostat THERMAFLEX
- termostat Yokis
- termostat ChiliTec
- termostat Eliwell
- termostat Plugwise
- termostat Johnson Control
- termostat Webasto
- termostat Drayton Erie
- termostat OJ ELECTRONICS
- termostat Tellur
- termostat RWE
- termostat Lowes
- termostat Jumo
- termostat Warmup
- termostat Qubino
- termostat STI
- termostat ELKO
- termostat TrickleStar
- termostat Gewiss
- termostat Sinustec
- termostat Rose LM
- termostat Otio
- termostat MundoControl
- termostat GENERAL Life
- termostat Oreg
Najnowsze instrukcje dla termostat
14 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024