Instrukcja obsługi Shimano FD-M986-D

Shimano Akcesoria rowerowe FD-M986-D

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Shimano FD-M986-D (1 stron) w kategorii Akcesoria rowerowe. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/1

(1) Set the chain to the largest rear

sprocket, and shift to the large

chainring.

3. Adjustment of the cable tension

General Safety Information

WARNING

• Be careful not to let the cuffs of your clothes get caught in the chain while riding, otherwise you may fall off

the bicycle.

• Obtain and read the service instructions carefully prior to installing the parts. Loose, worn or damaged

parts may cause the bicycle to fall over and serious injury may occur as a result. We strongly recommend

only using genuine Shimano replacement parts.

• Obtain and read the service instructions carefully prior to installing the parts. If adjustments are not

carried out correctly, the chain may come off and this may cause you to fall off the bicycle which could result

in serious injury.

• Read these Technical Service Instructions carefully, and keep them in a safe place for later reference.

Note

• The front derailleur is for double front chainwheels only. It cannot be used with triple front chainwheels, as

the shifting points will not match.

• If gear shifting operations do not feel smooth, wash the derailleur and lubricate all moving parts.

• If the amount of looseness in the links is so great that adjustment is not possible,

you should replace the derailleur.

• When the chain is in the position shown in the illustration, the chain may contact

the front chainrings or front derailleur and generate noise. If the noise is a

problem, shift the chain onto the next-larger rear sprocket or the one after.

•

For frames with suspension, the chain stay angle will vary depending on whether the

bicycle is being ridden or not being ridden. When the bicycle is not being ridden and

the chain is positioned on the largest/larger chainring and on the smallest sprocket,

the chain guide outer plate of the front derailleur may touch the chain.

• Shimano does not provide the bottom bracket mount fixing bolts.

• For smooth operation, use the specified outer casing and the bottom bracket cable guide.

• Parts are not guaranteed against natural wear or deterioration resulting from normal use.

• For maximum performance we highly recommend Shimano lubricants and maintenance products.

• For any questions regarding methods of installation, adjustment, maintenance or operation, please contact a

professional bicycle dealer.

• Be sure to read the service instructions for the Front Drive System in conjunction with these service

instructions.

After taking up the initial slack in the cable, re-secure to the front

derailleur as shown in the illustration.

Normal type Top route type

Pull

Set the height of the front derailleur. The flat section of the

chain guide outer plate should be directly above and

parallel to the larger chainring. Secure using a 5 mm allen

key.

Installation of the front derailleur

Tightening torque :

5 - 7 N·m {44 - 60 in. lbs.} Chain guide

Chainwheel (larger chainring)

SIS Adjustment

Be sure to follow the sequence described below.

1. Low adjustment

Set so that the clearance between the chain guide inner plate and the

chain is 0 - 0.5 mm.

2. Connecting and securing the inner cable

Switch the mode converter to

the 3x (triple mode) position,

and then check the lowest

position. Operate lever B two

times or more to set the lever

to the lowest position.

Remove the inner hole cover,

and install the cable.

Low adjustment

screw

Chain

Chain guide

inner plate

4. Top adjustment

Set so that the clearance

between the chain guide outer

plate and the chain is 0 - 0.5

mm.

Chain position

SI-5M90A-002-00

Specifications

Technical Service Instructions SI-5M90A-002

FD-M985

FD-M985-E / FD-M985-E2

FD-M986 / FD-M986-D

Front derailleur

• FD-M986-D

• FD-M985-E

• FD-M985-E2

• FD-M985 / M986

Tightening torque :

6 - 7 N·m {52 - 60 in. lbs.}

< Normal type >

• FD-M986 / FD-M986-D

< Top route type >

5 mm Allen key

8 mm spanner4 mm Allen key

< Normal type >

• FD-M985 / FD-M985-E / FD-M985-E2

< Top route type >

Note:

Pass the cable

through as shown

in the illustration.

Wire fixing bolt

Note:

Pass the cable

through as shown

in the illustration.

Wire fixing bolt

One Holland, Irvine, California 92618, U.S.A. Phone: +1-949-951-5003

Industrieweg 24, 8071 CT Nunspeet, The Netherlands Phone: +31-341-272222

3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan

* Service Instructions in further languages are available at :

http://techdocs.shimano.com

Please note: specifications are subject to change for improvement without notice. (English)

X = Available Chain

Chain guide

outer plate

Chain

Chain guide

inner plate

Outer casing adjustment barrel

Note:

When installing the components to carbon frame/handle bar surfaces, verify with the manufacturer of the carbon

frame/parts for their recommendation on tightening torque in order to prevent over tightening that can cause

damage to the carbon material and/or under tightening that can cause lack of fixing strength for the components.

For bracket type

Install as shown in the illustration.

Bolt

AdapterAdapter

Front Derailleur

Front Chainwheel

1,2Tightening torque :

35 - 50 N·m {305 - 435 in. lbs.}

3Tightening torque :

5 - 7 N·m {44 - 60 in. lbs.}

Install the front derailleur as shown in the illustration. At this time,

adjust the position of the front derailleur while installing it so that

there is a clearance of 1 - 3 mm between the chain guide outer

plate and the maximum outer diameter of the larger chainring.

Chain guide outer plate

Maximum outer diameter

Pro-Set gauge

1~3mm

Clearance:

Tightening torque :

5 - 7 N·m {44 - 60 in. lbs.}

42T 40T 38T

155.5 mm*

(From bottom

bracket center)

44T 42T 40T

Outside Inside

FD-M986

FD-M986-D

FD-M985

FD-M985-E

FD-M985-E2

Top adjustment

screw

FD-M986

FD-M986-D

FD-M985

FD-M985-E

FD-M985-E2

Front

chainrings

Rear

sprockets

Model number

Normal type

Top route type

Front chainwheel tooth difference

Front derailleur installation band diameter

Chainstay angle (a)

Applicable chain line

Note:

Do not force the mode select switch to turn. If you force it to turn, it

will break.

Mode converter

Mode select switch

Attach the same outer end cap to the cut end of the outer casing.

Outer end cap

Cutting the outer casing

When cutting the outer casing, cut the opposite end to the end with

the marking. After cutting the outer casing,

make the end round so that the inside of the

hole has a uniform diameter.

Install the inner hole cover by turning it as

shown in the illustration until it stops.

Do not turn it any further than this, otherwise

it may damage the thread on the cover.

Inner hole cover

Inner cable

Lever (B)

If the chain falls to the crank

side

Tighten the top adjustment screw

clockwise (about 1/4 turn).

Loosen the top adjustment screw

counterclockwise (about 1/8

turn). If it still does not solve the

problem, adjust the cable tension

again.

If shifting is difficult from the

small chainring to the large

chainring

5. Troubleshooting chart

After completion of steps 1 - 4, move the shifting lever to check the

shifting. (This also applies if shifting becomes difficult during use.)

If shifting is difficult from the

large chainring to the small

chainring.

Loosen the low adjustment screw

counterclockwise

(about 1/4 turn).

Tighten the top adjustment screw

clockwise (about 1/8 turn). If this

still does not solve the problem,

tighten the outer casing

adjustment barrel by turning it

clockwise by 1 to 2 turns.

If there is interference between

the chain and the front derailleur

inner plate when the chain is on

the large chainring and the

largest sprocket

If there is interference between

the chain and the front derailleur

outer plate at the large

chainring.

Loosen the top adjustment screw

by turning it counterclockwise

(about 1/2 turn).

If this still does not solve the

problem, loosen the outer casing

adjustment barrel by turning it

counterclockwise by 1 to 2 turns.

If the chain falls to the bottom

bracket side.

Tighten the low adjustment screw

clockwise (about 1/2 turn).

Smallest

sprocket

Large

chainring

Chain position

Largest

sprocket

Large

chainring

Chain position

Largest

sprocket

Small

chainring

(2) Adjust using the outer casing adjustment barrel so that the

clearance between the chain guide inner plate and the chain

is 0 - 0.5 mm.

• FD-M985-E / FD-M985-E2

Models without BB plate

Tightening torque :

5 - 7 N·m {44 - 60 in. lbs.}

Bottom bracket

mount

Bracket

Example: When using an Allen key

Bottom bracket mount fixing bolt

Note: Shimano does not provide

the bottom bracket mount

fixing bolts.

42T

Outside Inside

44T

38T 40T

Outside Inside

40T

159.5 mm*

(From bottom

bracket center)

* The installation height will vary depending on the

position of the frame washer.

Use an 8 mm spanner or a 4 mm Allen key to tighten the wire

fixing bolt.

Applicable front chainwheel For double chainwheel only

FC-M980 (38-26T), FC-M985 (40-28T, 42-30T, 44-30T)

46.8 mm

48.8 mm

FD-M985

14, 12T

S, M, L

66° - 69°

38T

40-44T

FD-M985-E

14, 12T

–

66° - 69°

–

40-44T

FD-M985-E2

12T

–

66° - 69°

38T

40T

FD-M986

14, 12T

S, M, L

66° - 69°

38T

40-44T

FD-M986-D

14, 12T

–

66° - 69°

38T

40-44T

Note:

The mode converter cannot be switched while the lever is at the

lowest position. Be sure to operate lever (A) one or more times

before switching. Do not turn the mode converter by force, otherwise

it may break.

Mode converter

Mode select switch

Lever (A)

Operate lever A once to set it to the middle position. Switch the

mode converter to the 2x (double mode) position.

Specyfikacje produktu

Marka:	Shimano
Kategoria:	Akcesoria rowerowe
Model:	FD-M986-D

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Shimano FD-M986-D, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Akcesoria rowerowe Shimano

Shimano FD-M985 Instrukcja

8 Października 2024

Shimano FD-M8000-L Instrukcja

4 Października 2024

Shimano FD-M6020-L Instrukcja

30 Września 2024

Shimano RD-R7000-SS Instrukcja

24 Września 2024

Shimano FD-M7000-10-E Instrukcja

20 Września 2024

Shimano SL-A050-LN Instrukcja

20 Września 2024

Shimano SM-RT70 Instrukcja

16 Września 2024

Shimano ST-M4000-L Instrukcja

14 Września 2024

Shimano SM-CA70 Instrukcja

14 Września 2024

Shimano FD-M8000-H Instrukcja

13 Września 2024

Instrukcje Akcesoria rowerowe

Najnowsze instrukcje dla Akcesoria rowerowe

Crivit IAN 270384 Instrukcja

10 Października 2024

Knog Oi Luxe Instrukcja

9 Października 2024

Abus WBA65 Instrukcja

8 Października 2024

Topeak PRESSURE-RITE SHOCK ADAPTER Instrukcja

7 Października 2024

Blackburn Honest Digital Shock Instrukcja

6 Października 2024

Funn Ripper Instrukcja

5 Października 2024

Funn Mamba Instrukcja

4 Października 2024

Basil Bremen Instrukcja

2 Października 2024

Basil SoHo Instrukcja

2 Października 2024

Basil Cento Instrukcja

2 Października 2024