Instrukcja obsługi Shimano FD-4600-B


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Shimano FD-4600-B (1 stron) w kategorii Akcesoria rowerowe. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/1
(3) After trimming, use the outer casing
adjustment barrel to adjust the
clearance between the chain and
chain guide to the minimum (0 - 0.5
mm).
Adjustment is possible at the dual
control lever (with cable adjuster).
For details on the adjustment
method, refer to the Service
Instructions for the ST-4600.
General Safety Information
Obtain and read the service instructions carefully prior to installing the parts.
Loose, worn or damaged parts may cause the bicycle to fall over and serious injury
may occur as a result. We strongly recommend only using genuine Shimano
replacement parts.
Obtain and read the service instructions carefully prior to installing the parts.
If adjustments are not carried out correctly, the chain may come off and this may
cause you to fall off the bicycle which could result in serious injury.
Be careful not to let the cuffs of your clothes get caught in the chain while riding,
otherwise you may fall off the bicycle.
Read these Technical Service Instructions carefully, and keep them in a safe place for
later reference.
Note
If gear shifting operations cannot be carried out smoothly, clean the derailleur and
lubricate all moving parts.
If the amount of looseness in the links is so great that adjustment is not possible, you
should replace the derailleur.
When the chain is in the position shown in the illustration,
the chain may contact the front chainrings or front derailleur
and generate noise. If the noise is a problem, shift the chain
onto the next-larger rear sprocket or the one after.
For smooth operation, use the specified outer casing and
the bottom bracket cable guide.
Grease the inner cable and the inside of the outer casing
before use to ensure that they slide properly.
Parts are not guaranteed against natural wear or deterioration resulting from normal
use.
For maximum performance we highly recommend Shimano lubricants and
maintenance products.
For any questions regarding methods of installation, adjustment, maintenance or
operation, please contact a professional bicycle dealer.
WARNING
Front
chainrings
Rear
sprockets
2. The level section of the chain guide outer plate should be
directly above and parallel to the largest chainring.
3. Secure using a 5mm Allen key.
Chainwheel
(largest chainring)
Chain guide
Tightening torque:
5 - 7 N·m
{44 - 60 in. lbs.}
Tighten the top adjustment screw clockwise
(about 1/4 turn).
Loosen the top adjustment screw
counterclockwise (about 1/8 turn).
Loosen the low adjustment screw
counterclockwise (about 1/8 turn).
Tighten the low adjustment screw clockwise
(about 1/8 turn).
Turn the outer casing adjustment barrel
clockwise (1/8 of a turn at a time) until
shifting to the small chainring becomes
smooth. Be careful not to turn the outer
casing adjustment barrel too far at this time,
otherwise shifting to the large chainring will
become more difficult.
1. Adjust so that the clearance between the chain guide outer
plate and the large gear is 1 - 3 mm before installing.
Technical Service Instructions SI-5MW0A-002
SIS adjustment
1. Low adjustment
Set so that the clearance between the chain guide inner
plate and the chain is 0 - 0.5 mm.
Largest
sprocket Inner chainring
Be sure to read these service instructions in conjunction with the service instructions for the
ST-4600 / ST-5700 / ST-6700 / SL-4600 before use.
4. Top adjustment
Set so that the clearance between the chain guide outer
plate and the chain is 0 - 0.5 mm.
2. Connection and securing of cable
While pulling the inner cable, tighten the wire fixing
bolt with a 5 mm allen key to secure the cable.
While turning the crank arm, gently operate lever (b) and check that the front derailleur
moves slightly toward the small chainring. If the front derailleur moves by a large
amount and the chain is set onto the small chainring at this time, loosen the top
adjustment bolt by 1/8th of a turn. Then, after returning the chain to its original position,
adjust and check the trimming mechanism.
Smallest
sprocket Outer chainring
Low adjustment
screw
Chain guide
inner plate
Chain
Pull
Tightening torque:
6 - 7 N·m {52 - 60 in. lbs.}
After taking up the initial slack in
the cable, re-secure to the front
derailleur as shown in the
illustration.
3. Adjustment of the cable tension
(1) When making the cable
adjustment, place the chain on
the largest sprocket at the rear;
and at the front, shift the chain to
the inner chainring and then set
it back onto the outer chainring.
Note:
There are two derailleur positions for the outer chainring. Make sure the derailleur is in
the inner side of the two positions.
Shift the derailleur from the inner chainring (L)
to the outer chainring (T), then gently press
the small lever (b) until a small click is felt.
(trim function).
(2) Perform the trimming.
(ST-4600 / ST-5700 / ST-6700)
Top adjustment
screw
Chain guide
outer plate
Chain
Trimming (noise-prevention mechanism)
Gently press the lever [
b.
(A “click” sound will be heard.)
Chain guide
inner plate
Chain
FD-CX70
FD-4600
FD-4600 FD-CX70
Clearance:
0 - 0.5mm
Outer casing
adjustment barrel
Largest
sprocket Outer chainring
Largest
sprocket Outer chainring
Front shifting
Lever [
b
From large chainring
to small chainring
Lever [
a
From small chainring
to large chainring
Adjustment point
Lever [
a
Lever [
b
Type Band type / Brazed on type
Front derailleur installation band diameter S (28.6mm), M (31.8mm), L (34.9mm)
Chainstay angle (C) FD-4600 (61° - 66°), FD-CX70 (63° - 66°)
Front chainwheel tooth difference 16 teeth or less
Chain line 43.5mm
Installation of the front derailleur
Clearance: 1 - 3 mm
Chain guide outer plate
Specifications
5. Troubleshooting chart
After completion of steps 1 - 4, move the shifting lever to check the shifting.
(This also applies if shifting becomes difficult during use.)
If the chain falls to the crank side
If shifting is difficult from the small chainring to the
large chainring
If shifting is difficult from the large chainring to the
small chainring
If the chain falls to the bottom bracket side.
If the gear shifting to the small chainring is stiff and
difficult to carry out after trimming.
SI-5MW0A-002-00
One Holland, Irvine, California 92618, U.S.A. Phone: +1-949-951-5003
Industrieweg 24, 8071 CT Nunspeet, The Netherlands Phone: +31-341-272222 3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan
* Service Instructions in further languages are available at : http://techdocs.shimano.com
Please note: specifications are subject to change for improvement without notice. (English)
© Feb. 2011 by Shimano Inc. XBC SZK Printed in Japan.
FD-4600
FD-CX70 Front derailleur
In order to realize the best performance, we recommend that the following
combination be used.
Series
Dual control lever
Shifting lever
Brake lever
Outer casing
Gears
Front derailleur
Front chainwheel
Rear derailleur
Freehub
Cassette sprocket
Chain
Bottom bracket cable guide
TIAGRA
ST-4600
SL-4600
BL-4600
OT-SP41
20
FD-4600
FC-4600 / FC-4650
RD-4600-SS
FH-4600
CS-4600
CN-4601
SM-SP17
Non series (Cyclo-cross)
ST-6700 / ST-5700
OT-SP41
20
FD-CX70
FC-CX70 / FC-CX50
RD-6700 / RD-5700
FH-6700 / FH-5700
CS-6700 / CS-5700
CN-6701 / CN-5701
SM-SP17
BA


Specyfikacje produktu

Marka: Shimano
Kategoria: Akcesoria rowerowe
Model: FD-4600-B

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Shimano FD-4600-B, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Akcesoria rowerowe Shimano

Shimano

Shimano FD-M985 Instrukcja

8 Października 2024
Shimano

Shimano FD-M8000-L Instrukcja

4 Października 2024
Shimano

Shimano FD-M6020-L Instrukcja

30 Września 2024
Shimano

Shimano RD-R7000-SS Instrukcja

24 Września 2024
Shimano

Shimano SL-A050-LN Instrukcja

20 Września 2024
Shimano

Shimano SM-RT70 Instrukcja

16 Września 2024
Shimano

Shimano ST-M4000-L Instrukcja

14 Września 2024
Shimano

Shimano SM-CA70 Instrukcja

14 Września 2024
Shimano

Shimano FD-M8000-H Instrukcja

13 Września 2024

Instrukcje Akcesoria rowerowe

Najnowsze instrukcje dla Akcesoria rowerowe

Crivit

Crivit IAN 270384 Instrukcja

10 Października 2024
Knog

Knog Oi Luxe Instrukcja

9 Października 2024
Abus

Abus WBA65 Instrukcja

8 Października 2024
Funn

Funn Ripper Instrukcja

5 Października 2024
Funn

Funn Mamba Instrukcja

4 Października 2024
Basil

Basil Bremen Instrukcja

2 Października 2024
Basil

Basil SoHo Instrukcja

2 Października 2024
Basil

Basil Cento Instrukcja

2 Października 2024