Instrukcja obsługi SereneLife SLPRWAS23

SereneLife Myjka wysokociśnieniowa SLPRWAS23

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla SereneLife SLPRWAS23 (2 stron) w kategorii Myjka wysokociśnieniowa. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
by
WARNING: Do not use the appliance before reading the instruction manual
This machine is designed for domestic use only
SLPRWAS23
HIGH PRESSURE WASHER
User Manual
Appliance is leaking
Slight leakage from the appliance pump is normal. lf the leakage increases
contract the authorized customer service.
Storage
In orderto prevent accidents or injuries, keep in mind the weight of the
appliance, pull out the telescopic rod (max length 410mm) when selecting
a storage location for it.
Storing the appliance
1. Park the machine on an even surface.
2. Press the disconnect on the trigger gun and remove the high pressure
hose from the trigger gun.
3. Push the casing of coupling forthe high pressure hose toward the rear
and disconnect the high pressure hose from the appliance.
4. lnsert the trigger gun into the holder.
5. Stow away the mains cable, the high pressure hose and accessories on
the appliance.
Prior to extended storage periods, as during the winter, also observe the
instructions in the care section.
Specication
Model No: SLPRWAS23
Power Supply: 110V
Power: 1200 Watt
Max pressure: Up to 1160+ psi
Water Flow: 300L / per Hour (5L/ per Min.)
Max water pressure: 80bar (8Mpa)
Working pressure: 6.5Mpa
Water temperature: 32-140° F
Environment temperature: 41-122° F
Weight: 14.35 lbs.
Length: 8.5 in
Width: 7.6 in
Height: 17.0 in
Symptom
Cause
Recommended action
Machine refused to
start
1.Machine
not
plugged
in
2.Defectiv
e
socket
3.Defective extension
cable
4.1ncorrect mains
voltage
5.Switch
o
6.Fuse has
blown
1. Plug in
machine
2.Try
another socket
3.Try
anothe
r
extension
cable
4.Check
voltage correctly
5.Turn on
switch
6.Replacefuse
Pump stop
working
Lack of water lead
to
high
temperature
check water ow
quantity
-put the hose in the
10
bottle (per
minute
)
Fluctuatin
g
pressure
1.Spray
lance
blocked
2. Pump is
sucking
air
3.
Impurities
in
pump
1. Clean lance with
needle
2.Check
that hoses
and
connections
are
airtight
3.Contact
the
dealer
Machine do not
reach
operation
pressure
1.Spray lance blocked or
worn
2.Short supply
of
water
3.Hose
kinked
4.Filter blocked
5.Hose blocked
1. Clean or change
spray
lance
2.Check
inlet ow
rate
3.Straighte
n
out
hose
4.Ciean
lter
5.Ciean hose
Trigger gun can be
used
Trigger gun is
locked
Unlock
trigger gun
Machine often starts
and
stops by
itself
1. Safety valve worn
out
2.Pump,high pressure
hose,
trigger
gun
is
leaking
1.
Contact
the
nearest
service center
2.Contact
the
nearest
service center
Troubleshooting
The content in this instruction manual (include accessories) is kept the nal
modifying and explanation rights
1 10 9 2
A
B
C
F
E
D
G
H
I
J
11
www.PyleUSA.comwww.PyleUSA.comwww.PyleUSA.comwww.PyleUSA.comwww.PyleUSA.com
In winter, please do not put the machine outside without draining
the water to avoid the damage to the machine. Just put it in a room
with frost prevention.
Safety instruction
Danger
1. Never touch the mains plug and the socket with wet hands.
2. The appliance must not be used ifthe power cord or important parts
of the appliance, e.g. high pressure hoses, trigger gun or safety devices
are damaged.
Please arrange for it to be replaced immediately by an authorised repair agent
or a skilled electrician.
3. The appliance may not be used in areas where a risk of explosion is
present.
4. The high pressure washer must not be directed at other persons or
directed by the user at him/her self to clean clothing or footwear.
5. lf the appliance is used in hazardous areas (e.g. lling stations) all ofthe
safety provisions and operating instructions detailed in this manual must
be observed.
6. Never use the appliance to clean objects containing hazardous
substances.
7. Vehicle tyres or tyre valves are susceptible to damage from the high
pressure washer and may burst. The rst indication of this is a
discoloration of the tyre.
Damaged vehicle tyres/tyre valves are highly dangerous. Ensure that a
distanc of at least 30 cm is observed when cleaning with the washer.
8. Risk of explosion. Do not spray ammable liquids. Never draw in uids
containing solvents or undiluted acids. This includes petrol, paint thinner
and heating oil. The spray mist thus generated is highly inammable,
explosive and poisonous. Do not use acetone, undiluted acids or solvents
as they are damaging to the materials from which is the appliance is
made.
Warning
1. The mains plug and the coupling of an extension cable must be
watertight and must never lay in the water.
2. Unsuitable extension cables can be hazardous. Only use extension cables
outdoors which have been approved for this purpose and labeled with a
sucient cable cross-section: 1-10m: 1.5mm² 10-30m: 2.5mm²
3. Always fully unroll electrical cables.
4. High pressure hoses, xtures and couplings are important forthe safety
of the appliance. Only use high pressure hoses, xtures and couplings
recommended by the manufacturer.
5. This appliance is not intended for use by persons with reduced physical,
sensory or mental capabilities. The appliance must not be operated by
children or persons who have not been instructed accordingly. Children
should be supervised to prevent them from playing with the appliance.
6. The operator must use the appliance correctly. When working with the
appliance, p2-he must considerthe local conditions and pay due care and
attention to other persons, in particular children who are nearby.
Caution
1. Do not use the machine ifthe persons nearby do not wear safety
protection device.
2. Wearing protective clothing and safety goggles to protect against
splash back containing water or dirt.
3. Create stability for the appliance prior to all work on or with the
appliance to prevent accidents or damage. The stability ofthe appliance is
warranted when it is placed on to an even surface.
4. For safety reasons, we recommend that you operate the appliance only
via an earth-leakage circuit breaker (max. 30mA).
5. Make sure that the power cord or extension cables are not damaged by
running over, pinching, dragging or similar. Protect the power cable from
heat, oil, and sharp edges.
6. Never leave the appliance unattended when it is in operation.
Operation
Package
Please check all accessories before opening the box. lf there is something
missing, please contact the dealers or sellers.
7 4 5 6
4. Install spray lance (pic E).
Push the spray lance into the trigger gun and fasten it by turning it
through 90 degree.
Water Supply
Impurities in the water can damage the high pressure pump and
accessories. All high pressure washer (except hot water system) use the
cold water. The suitable water temperature is 41°F to 140°F
Water supply from mains
Observe water supply regulations
For connection values, use bre-reinforced water hose (not included) with a
standard coupling, normally the length is 5m, connect the water hose to
the appliance and water supply.
1. Open the watertap
2. Unlock the lever on the trigger gun
3. Pull on the lever of the trigger gun
4. Turn on the appliance (pic F ON: open OFF: close)
Start up
Dry runs lasting longer than two minutes lead to damages to the high
pressure pump. lf the appliance does not build up pressure within two
minutes, switch it o and proceed as instructed in the Chapter
“Troubleshooting”. The trigger gun is subjected to recoil force when the
water washer is discharged. Make sure that you have a rm footing and are
also holding the trigger gun and spray lance rmly.
The spray lance has two main settings stream and fan for easy cleaning (pic H).
Illustration
Special accessories expand the possibilities of using your appliance.Please
contact thedealer for further information.
Illustrate accessories before start-up.
1. Install coupling for water connection (pic A).
Screw the coupling to the water connection on the appliance.
2. Install high pressure hose (pic B. pic J).
Insert the high pressure hose tightly in to coupling on the appliance, it
will lock in audibly.
Make sure the connection nipple is aligned correctly.Note:
Check the secure connection by pulling on the high pressure hose.
3. Install the storage of trigger gun (pic C).
Insert the storage of trigger gun and push down all the way.
Caution
Prior to cleaning, make sure that the high pressure washer is placed safely
on level ground. Wear protective goggles and protective clothing during
the cleaning process.
Notes: Release the lever ofthe trigger gun, the device will switch o again.
High pressure washer remains in the system.
Working with detergent
Use detergent when cleaning. Remove the lid from the detergent bottle
and press the detergent bottle into detergent (pic D).
Notes: The device is under low pressure when using detergent and pulling
out spray lance.
Release the lever on the trigger gun, lock the lever on the trigger gun,
insert the spray lance into trigger gun when interrupting operation.
Finish Operation
1. Turn o tap.
2. Press the lever on the trigger gun to release any remaining pressure and
water in the system.
3. Pull out the main plug.
4. Store the water hose and high pressure hose.
Maintenance and Care
Turn o the appliance and remove the mains plug prior to any care and
maintenance work. Prior to longer periods of storage, pull out the lter in
the detergent bottle and clean under running water. Pull out the lter in
the water connection and clean under running water (pic I).
Use the needle to clean the residue (pic L).
CONTENTS
Gerneral Information -----------------------------------------------------------------------3
Safety Instruction -------------------------------------------------------------------------- 4
Operation --------------------------------------------------------------------------------------5
Illustration -------------------------------------------------------------------------------------6
Maintenance and Care -------------------------------------------------------------------- 8
Troubleshooting -----------------------------------------------------------------------------9
Storage -------------------------------------------------------------------------------------- 10
Specication -------------------------------------------------------------------------------- 10
Circuit Diagram -----------------------------------------------------------------------------11
Dear customer,
Pis read and comply with these original instructions prior to the initial
operation of your appliance and store them for later use or subsequent
owners.
General Information
This high pressure washer is designed for domestic use only:
1. To clean cars, motorbikes, caravans, bicycles.
2. To clean patios, fences, garden walls, pathways, driveways and house
facades, particularly useful for cleaning blocked driveway.
3. To remove algae and moss from roofs, brickwork and guttering.
4. To clean garden tools and machinery, furniture and barbecues.
5. To clean hygienic of animal pens and their surrounding area.
With accessories, replacement parts and detergents approved by factory.
Observethe instructions provided with these detergents.
The packing material can be recycled. Please do not place the packaging
into the ordinary refuse for disposal, but arrange for the proper recycling.
Old appliances contain valuable materials that can be recycled. Please
arrange for the proper recycling of old appliances. Please dispose your
old appliances using appropriate collection systems.
Read symbols in the operating instructions
Danger: Immediate danger that can cause severe injury or even death.
Warning: possible hazardous situation that could lead to severe injury or
even death.
Caution: possible hazardous situation that could lead to mild injury to
persons or damage to property.
The high pressure washer may not be directed at persons,
animals, live electrical equipment or at the appliance itself.
Protect the appliance against frost.
1. Coupling for water
connection
11. Lock of high pressure
hose
2. Water
inlet
12. Back
body
3. Front
body
13. Storage of trigger
gun
4. On/O switch
14. Storage of spray
lance
5. Power
cord
6. Water
outlet
7. High pressure
hose
8. Trigger
gun
9. Spray
lance
10. Lock
trigger
gun
3
www.PyleUSA.comwww.PyleUSA.comwww.PyleUSA.comwww.PyleUSA.comwww.PyleUSA.com www.PyleUSA.com
8

Specyfikacje produktu

Marka: SereneLife
Kategoria: Myjka wysokociśnieniowa
Model: SLPRWAS23

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z SereneLife SLPRWAS23, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Myjka wysokociśnieniowa SereneLife

SereneLife

SereneLife SLCMPWT25 Instrukcja

8 Października 2024
SereneLife

SereneLife SLCMPWT40 Instrukcja

8 Października 2024
SereneLife

SereneLife SLCMPWT75 Instrukcja

8 Października 2024
SereneLife

SereneLife SLCATL490 Instrukcja

8 Października 2024
SereneLife

SereneLife SLPRWAS46 Instrukcja

22 Września 2024
SereneLife

SereneLife SLCATL420 Instrukcja

22 Września 2024
SereneLife

SereneLife SLCATL520 Instrukcja

21 Września 2024
SereneLife

SereneLife SLCATL320 Instrukcja

21 Września 2024
SereneLife

SereneLife SLCATL360 Instrukcja

20 Września 2024
SereneLife

SereneLife AZSLCATL320 Instrukcja

18 Września 2024

Instrukcje Myjka wysokociśnieniowa

Najnowsze instrukcje dla Myjka wysokociśnieniowa

Nilfisk

Nilfisk C 110.3-5 PC X-TRA Instrukcja

15 Października 2024
Sun Joe

Sun Joe SPX3001-RM Instrukcja

14 Października 2024
Worx

Worx WG629.1 Instrukcja

13 Października 2024
PowerPlus

PowerPlus POWXG9025 Instrukcja

10 Października 2024
Cecotec

Cecotec HidroBoost 1400 Instrukcja

9 Października 2024
Einhell

Einhell RT-HP 1648 TR Instrukcja

9 Października 2024
Einhell

Einhell RT-HP 1545 Instrukcja

9 Października 2024
Einhell

Einhell HR 160 Instrukcja

9 Października 2024
Anova

Anova H1800 Instrukcja

8 Października 2024
Anova

Anova H1950 Instrukcja

8 Października 2024