Instrukcja obsługi Scosche TA2047B

Scosche zestaw samochodowy TA2047B

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Scosche TA2047B (4 stron) w kategorii zestaw samochodowy. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/4
1
142TA2047B
IN-DASH INSTALLATION KIT FOR
2001-UP TOYOTA RAV4 /
2000-UP MR2 SPYDER
1987-UP TOYOTA VEHICLES
Rear Speaker Plug
1 = Right Rear Negative
2 = Left Rear Negative
3 = Right Rear Positive
4 = Empty
5 = Empty
6 = Left Rear
Positive
CAR STEREO CONNECTOR
PROVIDE EASY CONNECTION
OF YOUR CAR STEREO
TO FACTORY WIRING
HARNESS.
TA02
1987-up Toyota
©2001 SCOSCHE INDUSTRIES, INC. SI 9/01-142TA2047B (3000005)
If you have any further questions, call TECH HELP 1-800-621-3695, ext. 3
142TA2047B
RAV4
MOUNTING
BRACKET
142TA2047B
POCKET
142TA2047B
TRIM RING
142TA2047B
MOUNTING
PANEL
Front Speaker and PowePlug
1 = Right Front Negative
2 = Left Front Negative
3 = Accessory +12V
4 = +12V Constant, Battery
5 = Right Front Positive
6 = Left Front Positive
7 = Chassis Ground
8 = Empty
9 = Empty
10 = Illumination +12V
LIABILITY DISCLAIMER
This instruction booklet is based on carefully documented data and research of automobile dash disassembly, wire harness/codes and
information pertaining to installation of this kit (142TA2047B) in 2001-UP Toyota RAV4 / 2000-UP MR2 Spyder vehicles. Scosche
Industries, Inc. can not be held responsible for discrepancies/inconsistencies that may occur due to the automobile manufacturing
changes or options, or damage that may occur in the automobile during the installation of components while using this booklet.
2
DIN RADIO INSTALLATION (DETACHABLE FACE/PULLOUT)
Slide the mounting sleeve (metal shroud) into the panel’s radio opening and bend all available mounting
tabs outward (see inset). Once the radio mounting sleeve has been fastened to the kit panel, slide the
radio into the mounting sleeve until it locks into place.
NOTE: The mounting sleeve must be removed from the radio first!
Your radio may be snapped into its sleeve. Slide the mounting
sleeve (metal shroud) off the radio towards the back.
INTRODUCTION
This premium installation kit is for 2000-Up Toyota MR2 Spyder and 2001-Up RAV4 vehicles. Included
are all of the parts you need to mount your car stereo/cassette or CD player into your vehicle’s dash.
Refer to the individual instruction in this manual to remove your vehicle’s factory radio and assemble the
kit.
CAUTION: Disconnect your vehicle's negative battery terminal before the installation to help
prevent electrical damage. We recommend the use of a volt/ohm meter over a test light to
check wiring. A test light or grounded wire probe can cause damage to the vehicle's
computer and/or diagnostic systems. Avoid all factory air bag wiring - air bags can
accidentally deploy causing serious injury or death.
NOTES:
• See your vehicle’s instructions for any special tools your installation requires.
• Read all instructions accompanying your car stereo/cassette player for proper wiring and mounting
instructions.
CAUTION:
REAR SUPPORTING THE
RADIO ADDS TO THE
INSTALLATION’S
STRUCTURAL INTEGRITY.
DIN RADIO
REAR SUPPORT
STRAP
142TA2047B
MOUNTING
PANE
RADIO
MOUNTING
SLEEVE
142TA2047B
TRIM RING
BEND
TABS
OUTWARD
RAV4 BRACKET ASSEMBLY
BACK VIEW OF
MOUNTING
PANEL
BACK VIEW
OF POCKET
RAV4 BRACKET INSTALLATION
1. The bracket is only used for
installation in Toyota RAV4.
2. Align the snaps of RAV4 mounting
bracket with the pocket slots.
3. When aligned, snap bracket
carefully into position until locked.
CAUTION:
REAR SUPPORTING THE
RADIO ADDS TO THE
INSTALLATION’S
STRUCTURAL INTEGRITY.
2000-UP TOYOTA MR2 SPYDER
RADIO REMOVAL AND IN-DASH INSTALLATION:
Note: The factory radio provision is for a Double ISO/DIN style radio.
1. Use panel removal tool to remove left and right plastic side panels, extract (1) Phillips screw from
behind each panel.
2. Remove climate control knobs, and extract (2) Phillips screws.
3. Remove radio trim bezel.
4. Remove ash tray and extract (1) 10mm bolt on the right side, carefully pry out ash tray trim bezel,
disconnect and remove.
5. Extract (4) Phillips screws securing radio, disconnect and remove from dash.
USE THE SHADED MOUNTING TABS. CUT OFF THE REMAINING TABS AND DISCARD.
CAUTION:
REAR SUPPORTING THE
RADIO ADDS TO THE
INSTALLATION’S
STRUCTURAL INTEGRITY.
USE
THESE
TABS
USE
THESE
TABS
3

Specyfikacje produktu

Marka: Scosche
Kategoria: zestaw samochodowy
Model: TA2047B

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Scosche TA2047B, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje zestaw samochodowy Scosche

Scosche

Scosche HA1714B Instrukcja

28 Grudnia 2024
Scosche

Scosche BTFreq Pro Instrukcja

7 Października 2024
Scosche

Scosche KA2091B Instrukcja

23 Września 2024
Scosche

Scosche auxMIC Instrukcja

22 Września 2024
Scosche

Scosche KA2070B Instrukcja

22 Września 2024
Scosche

Scosche NN1640B Instrukcja

22 Września 2024
Scosche

Scosche TA2074B Instrukcja

22 Września 2024
Scosche

Scosche TA2077B Instrukcja

22 Września 2024
Scosche

Scosche TA2079B Instrukcja

22 Września 2024
Scosche

Scosche HA1709B Instrukcja

22 Września 2024

Instrukcje zestaw samochodowy

Najnowsze instrukcje dla zestaw samochodowy

Nokia

Nokia HF-33W Instrukcja

15 Stycznia 2025
Renegade

Renegade REN10KIT Instrukcja

30 Grudnia 2025
Metra

Metra 95-5026 Instrukcja

28 Grudnia 2024
Metra

Metra 95-7883HG Instrukcja

28 Grudnia 2024
Metra

Metra AX-ADCT4 Instrukcja

28 Grudnia 2024
Metra

Metra 99-7345B Instrukcja

28 Grudnia 2024
Metra

Metra 99-7339B Instrukcja

28 Grudnia 2024
HTC

HTC Car Kit Instrukcja

15 Grudnia 2024
Metra

Metra 99-7367HG Instrukcja

8 Października 2024
Metra

Metra 99-8223 Instrukcja

8 Października 2024