Instrukcja obsługi Saturn ST-HC7386

Saturn kosiarka ST-HC7386

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Saturn ST-HC7386 (20 stron) w kategorii kosiarka. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/20

ST-HC7386

HAIR CLIPPER

МАШИНКА ДЛЯ СТРИЖКИ

HAIR CLIPPER

Dear Buyer!

We congratulate you on having

bought the device under trade

name “Saturn”. We are sure that

our devices will become faithful

and reliable assistance in your

housekeeping.

Avoid extreme temperature

changes. Rapid temperature

change (e.g. when the unit is

moved from freezing temperature

to a warm room) may cause

condensation inside the unit and a

malfunction when it is switched

on. In this case leave the unit at

room temperature for at least 1.5

hours before switching it on.

If the unit has been in transit,

leave it indoors for at least 1.5

hours before starting operation.

READ ALL INSTRUCTIONS BEFORE

USING AND SAVE THESE

INSTRUCTIONS

BLADE ALIGNMENT

Your clippers were carefully

examined to ensure, that the blades

were oiled and aligned before leaving

our factory.

Blades must be realigned, if they

have been removed for cleaning or

replacement.

To realign the blades, simply

match the upper and bottom blades

teeth up, point for point.

(End of top blade teeth should be

approximately 1.2mm back from

bottom blade; compare your clipper

blades with the sketch).

If blade alignment is incorrect,

add a few drops of oil to the blades,

turn clipper on for a few moments,

turn off and unplug. Loosen screws

slightly and adjust. Tighten screws

after blade is aligned.

OIL

To maintain your clipper in peak

condition, the blades should be oiled

every few haircuts.

Do not use hair oil, grease, oil

mixed with kerosene or any solvent,

as the solvent will evaporate and leave

the thick oil, which may slow down the

blades motion.

BLADE LEVER

The lever is conveniently located

near your thumb (If you’re right-

handed), so it can easily be adjusted

while the clipper is in your hand.

The lever adds versatility to your

clipper by allowing you to gradually

change the closeness of your cut

without an attachment comb.

When the lever is in the

uppermost position, the blades will

give you the closest cut and leave the

hair very short. Pushing the lever

downward gradually increases the

cutting length.

In its lowest position, the lever

will leave the hair approximately the

same length as a No. 1 comb.

The lever will also extend the use

of your blades, since a different

cutting edge is used in each setting.

In addition, if extremely heavy

hair cutting has jammed the blades, it

will help you remove hair that has

become wedged between the two

blades without removing the blades.

While the clipper is running,

rapidly move the lever from “close

cut” to “longer cut” a couple of times.

Doing this each time after you have

finished using your clipper, will help to

keep the blades clear of cut hair. If

your clipper stops cutting and this

does not help, your cutting blades are

blunt. Replace them with new blades.

IMPORTANT SAFEGUARDS

When using electrical appliances,

especially when children are present,

basic safety precautions should always

be followed, including the following:

To reduce the risk of death or injury

from electric shock:

Unplug this appliance before

cleaning.

Do not place or store appliance,

where it can fall or be pulled into a tub

or sink.

Do not use, while bathing or in a

shower.

Do not place in or drop into water

or other liquid.

Do not reach for an appliance that

has fallen into water. Unplug

immediately.

To reduce the risk of burns,

electrocution, fire or injury to persons.

Use this appliance only for its

intended use, as described in this

manual. Do not use attachments, not

recommended by the manufacturer.

This appliance should never be

left unattended, when plugged in.

Close supervision is necessary,

when this appliance is used by, on or

near children or invalids.

Never operate this appliance, if it

has a damaged cord or plug, if it is not

working properly.

Keep the cord away from heated

surfaces.

Do not pull, twist or wrap line

cord around appliance.

Never drop or insert any object

into any opening on this appliance.

Before use, make certain blades

are aligned properly.

Do not place appliance on any

surface, while it is operating.

Do not use this appliance with a

damaged or broken comb nor with

teeth missing from the blades, as

injury may occur.

INSTRUCTIONS FOR HAIR

CUTTING

Before starting the hair cut:

1. Inspect the clipper, making sure

that it is free of oil between the

cutting blade teeth and turn the unit

on to distribute the oil and to make

sure it is running smoothly. Wipe off

any excess oil. This should be done

after each use. While using the unit,

untwist the cord from time to time to

avoid tangling.

2. Seat the person so their head is

approximately at your eye level. This

allows ease of visibility, while cutting

and a relaxed control of the unit.

3. Before cutting always first comb

the hair, so it is tangle free and as it is

naturally worn.

4. Place a towel around the neck and

shoulders of the person having the

haircut.

REMINDERS

Cut the hair in a relaxed and slow

manner. Use short strokes only to

work gradually over the entire head.

Always take off a little hair at a

time, you can always trim off

additional hair later.

As you work, comb the hair

frequently back into the style to which

you are cutting.

When cutting with this hair

clipper, it is better to leave the hair

dry, not wet. With the hair dry, it is

much easier to control the amount of

hair being cut.

BEGINNING THE HAIRCUT

Cutting hair requires practice, so it is

always better to leave the hair longer

for the first few haircuts, until you

become used to the length, to which

each attachment cuts the hair.

ATTACHMENT COMB (see main

diagram)

Attachment Comb No. 1 leaves

3mm hair length.

Attachment Comb No. 2 leaves

6mm hair length.

Attachment Comb No. 3 leaves

9mm hair length.

Attachment Comb No. 4 leaves

12mm hair length.

Each comb attachment is marked

accordingly on its outside middle

surface.

To attach a comb, hold it with

teeth showing, and slide it onto and

along the clipper blade, until the front

of the comb firmly rests against the

clipper blade.

To remove the comb, simply pull

the comb upward and away from the

clipper blade.

For even cutting, allow the comb

attachment / cutter to cut through the

hair. Do not force it through. Also

remember to comb the hair frequently

to remove trimmed hair and to check

for uneven strands.

STEP 1 - NAPE OF THE NECK

1. Attach comb attachment 3mm or

6mm.

2. Hold the clipper cutting edge

pointed up and begin the haircut,

starting at the centre of the head at

the base of the neck (see diagram 1).

3. Hold the clipper comfortably in

your hand and hold lightly against the

head with the comb teeth pointing

upward. Gradually and slowly lift the

clipper, working upwards and outwards

through the hair, trimming just a little

at a time.

4. As you cut, gradually lift the hair

clipper head towards you. Continue to

cut the back area from the bottom of

the neck upwards to the top of the

ears.

STEP 2 - BACK OFTHE HEAD

Change to the next longest comb

attachment 9mm or 12mm and cut

the back of the head (see diagram 2).

Specyfikacje produktu

Marka:	Saturn
Kategoria:	kosiarka
Model:	ST-HC7386

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Saturn ST-HC7386, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje kosiarka Saturn

Saturn ST-HC7381 Instrukcja

11 Stycznia 2025

Saturn ST-HC7386 Instrukcja

29 Sierpnia 2024

Saturn ST-HC1540 Instrukcja

21 Sierpnia 2024

Instrukcje kosiarka

Najnowsze instrukcje dla kosiarka

RYOBI RLM3715A Instrukcja

13 Stycznia 2025

BaByliss E974E Instrukcja

13 Stycznia 2025

Sun Joe 24V-X2-21LM-RM Instrukcja

13 Stycznia 2025

Texas Raser 484 TR Instrukcja

13 Stycznia 2025

Craftsman CMXGMAM7815145 Instrukcja

13 Stycznia 2025

Remington HC5015 Apprentice Instrukcja

12 Stycznia 2025

Güde FS 36-302-30 Instrukcja

12 Stycznia 2025

Herkules MB 470 EW Instrukcja

12 Stycznia 2025

Zoef Robot Hendrik-Jan - MR13Z Instrukcja

11 Stycznia 2025

Echo SRM-235 Instrukcja

11 Stycznia 2025