Instrukcja obsługi Sani-Lav ESB2-501L

Sani-Lav Zlew ESB2-501L

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Sani-Lav ESB2-501L (9 stron) w kategorii Zlew. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/9
1
A C O R B AT T E R Y P O WERE D
S I N K W I T H E L E C T R O N I C S E N S O R
Operating Manual for Hands-Free Floor Mount Stainless Steel Sink
AC Models ES2-501L and ES2-501L-0.5
Battery Models ESB2-501L and ESB2-501L-0.5
of Domestic and Foreign Parts
Columbia does not recommend use with harsh chemicals.
Product Compliance
NSF/ANSI 2 Food Equipment, NSF/ANSI 372 Lead-Free Compliant, ASME A112.18.1
2
A C O R B AT T E R Y P O W E R E D
COLUMBIA SPECIFICATIONS S I N K W I T H E L E C T R O N I C S E N S O R
800.626.2117 columbiasinks.com info@columbiasinks.com
©2021 Columbia Products
Parts List
(1) Sink bowl
(1) Pedestal base
(6) Nuts and washers to attach bowl to pedestal base
(1) AC or battery powered sensor faucet assembly
(1) Strainer assembly with basket
(1) Mixing check valve
Installation Instructions
Step 1
1. Install strainer assembly.
2. Attach bowl to pedestal base by slipping bolts on bowl through openings on pedestal base as
shown in illustration A.
3. Tighten the 6 nuts to the threaded bolts under bowl. Do not over-tighten.
Step 2
1. Install faucets to the sink following the instructions provided with sensor unit.
2. Attach supply tube with elbow to back of faucet.
3. Install mixing check valve and compression fitting to control box of each sensor faucet.
Step 3
1. Place sink at the desired location.
2. Mark the floor where the four holes are at the pedestal base as shown in illustration B.
3. Drill holes as required for mounting hardware (Hardware not included).
Step 4
1. Secure sink to floor.
2. Connect waste line to strainer assembly.
1. Mount sensor control box at desired location on wall.
2. Connect power line from sensor to control box.
3. Attach supply tube from faucet to control box.
4. Connect hot and cold water from the source to mixing check valve.
5. Remove aerator from the spout and flush water system. (see step 7 sensor installation
instructions)
6. Check connections for leaks.
7. Replace aerator onto the spout.
WARNING: This product can expose you to chemicals including Chromium (hexavalent compounds),
Lead, and Phthalates (DEHP) which are known to the State of California to cause cancer and birth defects
or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
NOTE: Lead content originates from Brass components in valves and faucets and is certied under
NSF/ANSI 372 as containing less than 0.25% lead in wetted surfaces.
Notice for California Consumers
Tools Required
Tape measure
Adjustable wrench
Drill motor and drill bits
Pipe wrench
Level
Safety glasses
Screw drivers: phillips and standard
Pencil
Socket wrench
Go to for more information on replacement parts and installation videos.columbiasinks.com
Illustration A
Illustration B
3
A C O R B AT T E R Y P O W E R E D
COLUMBIA SPECIFICATIONS S I N K W I T H E L E C T R O N I C S E N S O R
800.626.2117 columbiasinks.com info@columbiasinks.com
©2021 Columbia Products
16.5”
(419mm)
21
(533mm)
45º
9.5”
(241mm)
9.5”
(241mm)
19 (483mm)
17 (432mm)
2 drain hole
9.5”
(241mm)
7
(197mm)
25 (635mm)
1.25 R
32mm
Hole Configuration
Front Side
Top
6 (152mm)
9.5” (241mm)
5.75 (146 mm)
18
(457mm)
14
(356mm)
2 (51mm)
.875 (22mm)
dia. key hole
7.5” (191mm)
6 (152.4mm)
0.875(22.225mm)
11.375” (288.925mm) 4.25 (107.95mm)
Floor Mounting Detail
.375 dia. Floor
Mounting Holes
4.25” on Center


Specyfikacje produktu

Marka: Sani-Lav
Kategoria: Zlew
Model: ESB2-501L

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Sani-Lav ESB2-501L, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą