Instrukcja obsługi Rupert Neve Designs R10


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Rupert Neve Designs R10 (2 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 10 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/2
R10
Ten Space 500 Series Rack
Thank you for your purchase of the R10: Ten Space 500 Series Rack. Everyone at Rupert Neve Designs hopes
you enjoy using this tool as much as we have enjoyed designing and building it.
Usage Notes
The R10 has 10 x 500 series slots, with ample power, and both XLR and TRS inputs and outputs in a
rackmountable 3RU steel chassis. To use the R10, carefully slide each 500 series module in such that the
edge connector card fits snuggly into the slot in the back, and tighten both front panel screws for each
module. The current draw meter will display the total current being used by the installed modules. The
R10 has dual XLR and TRS inputs and outputs. With regard to the parallel XLR and TRS connectors, it is
recommended to connect ONLY ONE input on a given channel at a time (including to a patchbay). For the
outputs, it is generally not problematic to use both outputs to send a signal to two different destinations,
however for different modules, longer cable runs and different destinations, using both outputs in parallel
may cause issues, so be aware when using both outputs simultaneously.
Link
To enable VCA linking between modules, reset the corresponding jumper located by the card slots to the
LINK position. The linking function is set in pairs so that you can link channels 1-2, 3-4, ....etc.. The link func-
tion is typically used to link the VCA circuitry of compressors (such as our 543 module). Most other types of
modules are not linkable unless specifically noted by the manufacturer.
R10 Specifications
DC Voltage to Units +/-16VDC and +48VDC for phantom power
Max Output Current 2650mA total (2400mA modules and 250mA for phantom power)
Power Requirements 100-240VAC, 50/60Hz, 120 Watts
Weight 14lbs
Dimensions 19” long x 7.5”deep x 5.5” high
P/N 775-00029, Rev A
Front / Back Panel
R10: Ten Space 500 Series Rack
Current Meter
Link Jumper
Card Slot
There are three link jumpers,
which can be individually set
to allow VCA linking on
Channels 1-2, 3-4, 5-6, 7-8
and 9-10
The current meter monitors
the current draw on the
power supply
Each card slot is designed to
fit a standard 500 series
module
Channel OutputChannel Input
IEC Input
Each channel features a
balanced XLR and TRS input,
which are wired in parallel.
ONLY CONNECT ONE INPUT
AT A TIME
Each channel features a
balanced XLR & TRS output.
The IEC power input accepts
100-240VAC, 50/60Hz input


Specyfikacje produktu

Marka: Rupert Neve Designs
Kategoria: nieskategoryzowany
Model: R10

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Rupert Neve Designs R10, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje nieskategoryzowany Rupert Neve Designs

Instrukcje nieskategoryzowany

Najnowsze instrukcje dla nieskategoryzowany

Meec Tools

Meec Tools 010-084 Instrukcja

6 Października 2024
Outwell

Outwell Scenic Road 250 Instrukcja

5 Października 2024
Impact

Impact QuikBalance Instrukcja

4 Października 2024
Impact

Impact CA-112 Instrukcja

4 Października 2024
Impact

Impact LS-BHA Instrukcja

4 Października 2024
Impact

Impact LKB-5C Instrukcja

4 Października 2024
Impact

Impact RST-001 Instrukcja

4 Października 2024