Instrukcja obsługi Rostra 250-8807
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Rostra 250-8807 (4 stron) w kategorii Spiegel. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/4
Rostra Precision Controls, Inc. - 2519 Dana Dr. - Laurinburg, NC 28352 - 800-782-3379 - rostra.com Page 1
REARSIGHT CAMERA SYSTEM
250-8807 Mirror Installation Instructions
Parts Identification Page 1
Vehicle Preparation Page 1
System Layout Page 2
Installation Page 2
Testing and Reassembly Page 3
Troubleshooting Page 4
Parts Identification
Item Qty. Part Number Description
1 1 250-8807 LCD mirror monitor with gyro
2 1 N/A CAN Interface Harness
3 1 250-8025 Hardware service pack (cable ties, fuse holder, foam tape, etc...)
Vehicle Preparation
Before beginning your installation, familiarize yourself with the installation instructions and the RearSight camera system
components.
To ensure your safety, (A) apply the emergency brake and (B) read this entire manual before beginning.
CAUTION: It is advisable to disconnect the negative battery cable for 3 minutes before beginning
installation to avoid unintended air bag deployment. Note and record any anti-theft radio codes prior to
disconnecting.
Form #5421, Rev. A, 03-07-13
Rostra Precision Controls, Inc. - 2519 Dana Dr. - Laurinburg, NC 28352 - 800-782-3379 - rostra.com Page 2
System Layout
* CAN Interface Harness must be used in mirror harness pin location 2 when factory mirror harness does not
include CAN bus data line. See harness pin location diagram below.
Connector 9039 – Factory Electrochromatic/Gyro-equipped Mirror Harness Pin Locations
1. FUSE – 32 OR CIRCUIT
BREAKER
2. CTRL MOD. – LIN BUS
#SPDJB 1
3. NOT USED
4. GROUND – COWL
SIDE/PILLAR A LEFT
5. NOT USED
6. NOT USED
7. NOT USED
8. CAMERA POSITIVE (+)
YELLOW
9. CTRL MOD. – RELAY
REVERSE LAMP
10. NOT USED
11. CTRL MOD. – EC MIRROR
12. NOT USED
13. NOT USED
14. NOT USED
15. CTRL MOD. – EC MIRROR
16. CAMERA NEGATIVE (-)
BLACK
Rostra Precision Controls, Inc. - 2519 Dana Dr. - Laurinburg, NC 28352 - 800-782-3379 - rostra.com Page 3
Installation
1. Disconnect the mirror wiring harness and remove the factory rear view mirror from the vehicle’s windshield
using either a mirror removal tool or other device to free the locking tab within the mirror stem base.
2. Determine if the factory mirror harness includes the following:
A. Pin 1- Ignition 12-volt power supply
B. Pin 2 – CAN bus data line
C. Pin 9 – Reverse-triggered 12-volt power supply
D. Pin 8 – Empty
E. Pin 16 – Empty
3. If there is no pin present in pin location 2 of the factory mirror harness, the included CAN Interface Harness
must be inserted and routed to the BCM Ignition Connector at the passenger-side kick panel. Here the
installer will use the include wire splice connectors to connect to Pin 52 (Blue with white stripe wire).
4. Insert the yellow (positive) bullet connector from the supplied female RCA terminal into pin location 8 of the
factory mirror harness.
5. Insert the black (negative) bullet connector from the supplied female RCA terminal into pin location 16 of
the factory mirror harness.
6. Connect the male RCA plug from the camera to the female RCA terminal included with this mirror.
Late 2012 F150/Super Duty BCM Ignition Connector Late 2012 F150/Super Duty BCM Reverse Connector
Testing and Reassembly
Testing
1. Reconnect the negative battery cable and torque to 3 ft-lbs.
2. Re-enter any theft deterrent information (if applicable).
3. Turn the ignition switch to the ON position.
4. Shift the vehicle into reverse and confirm video feed to your device.
Note: If there is no picture present, re-check all harness connections.
Reassembly
1. Once the video is confirmed to be displaying in the mirror when in reverse, attach the new mirror to the
windshield.
2. Reinstall all trim pieces taking special care to ensure harnesses and wiring connections are properly secured.
3. Make sure no harnesses are bent or pinched by trim pieces.
4. Reconnect all disconnected bulbs and check for function.
Specyfikacje produktu
| Marka: | Rostra |
| Kategoria: | Spiegel |
| Model: | 250-8807 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Rostra 250-8807, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Spiegel Rostra
6 Września 2024
Instrukcje Spiegel
- Spiegel Ikea
- Spiegel Beurer
- Spiegel Boss
- Spiegel Adler
- Spiegel BaByliss
- Spiegel Conair
- Spiegel Orbegozo
- Spiegel Homedics
- Spiegel V-TAC
- Spiegel Scarlett
- Spiegel Innoliving
- Spiegel Lanaform
- Spiegel Revlon
- Spiegel Monacor
- Spiegel Miomare
- Spiegel Livarno
- Spiegel Carmen
- Spiegel Valera
- Spiegel Sanexo
- Spiegel Personal Care
- Spiegel Fenomé
- Spiegel Bobrick
- Spiegel Viidako
- Spiegel Kristall Form
- Spiegel Coaster
Najnowsze instrukcje dla Spiegel
9 Października 2024
9 Października 2024
9 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024