Instrukcja obsługi Roland Super UA


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Roland Super UA (2 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 36 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/2
English
Before using this unit, carefully read the leaet “USING THE UNIT SAFELY. After reading, keep the document(s) including those sections where it will be available for immediate reference.
Copyright © 2015 ROLAND CORPORATION
Install the Driver
In order to use the Super UA, you must download the driver from the following URL
to your computer and install it.
For details on installation, refer to the following URL.
& http://roland.cm/superua
NOTE
Do not connect the Super UA to your computer until you have nished installing
the driver.
If you have already connected the Super UA, disconnect it, and then re-connect it
after driver installation is completed.
Control panel
You can make detailed settings for the Super UA by using a dedicated control
panel installed on your computer.
The control panel becomes available after you install the driver.
For details on use, refer to the control panel help.
Panel Descriptions
* To prevent malfunction and equipment failure, always turn down the volume, and turn
o all the units before making any connections.
Main unit, front panel
1 2 3 4
Main unit, top panel
8
6
5
7
Use the jack that ts the plug
of your headphones
1 [MIC 1], [MIC 2]
buttons
Press when you want to adjust the sensitivity of the MIC 1 or
MIC 2 jack.
2 [LINE IN] button Press when you want to adjust the sensitivity of the LINE IN
jacks.
3 [PHONES] button Press when you want to adjust the volume of the PHONES
jacks.
4 [A], [B] buttons
Press when you want to adjust the volume of the LINE OUT A
or LINE OUT B jacks. Press the [A] button if you want to
output sound from the LINE OUT A jacks, or press the [B]
button if you want to output sound from the LINE OUT B
jacks. By using the control panel you can also output sound
from both the LINE OUT A and B jacks.
5 Level indicator Indicates the volume level of the jacks corresponding to the
button that is lit green.
6 Volume indicator
Indicates the volume level or sensitivity level of the jacks
corresponding to the button that is lit green.
7 Volume dial
Adjusts the volume or sensitivity of the jacks corresponding
to the button that is lit green. Press the dial to switch mute
on/o.
8 PHONES jacks Connect headphones here.
Button [MIC 1], [MIC 2], [LINE IN] buttons [PHONES], [A], [B] buttons
Unlit Sound cannot be input Sound cannot be output
White Sound can be input Sound can be output
Green The level indicator indicates the volume level, and the volume dial adjusts
the sound
Adjusting the volume/sensitivity
2
1
Press
Any one
Turn
14
AC Outlet
Power Cord
Place the AC adaptor so the side with
the indicator faces upwards and the
side with textual information faces
downwards. The indicator will light
when you plug the AC adaptor into an
AC outlet.
Included
USB cable
11 12 13
Main unit, rear panel
910
9 DC IN jack Connect the included AC adaptor.
10 Ground terminal
Depending on the circumstances of a particular setup, you
may experience a discomforting sensation, or perceive that
the surface feels gritty to the touch when you touch this
device, microphones connected to it, or the metal portions of
other objects. This is due to an innitesimal electrical charge,
which is absolutely harmless. However, if you are concerned
about this, connect the ground terminal with an external
ground. When the unit is grounded, a slight hum may occur,
depending on the particulars of your installation. If you
are unsure of the connection method, contact the nearest
Roland Service Center, or an authorized Roland distributor, as
listed on the “Information page.
Unsuitable places for connection
5Water pipes (may result in shock or electrocution)
5Gas pipes (may result in re or explosion)
5Telephone-line ground or lightning rod (may be
dangerous in the event of lightning)
11 I/O port Connect the cable that extends from the breakout box. If
you’re not using the breakout box, this connector is not used.
12 LINE OUT A jacks
Connect your monitor speakers etc.
Nominal output level +4 dBu (balanced)
Headroom +18 dB
Supported plugs:
1/4-inch TRS phone type
(balanced)
13 LINE IN jacks
Connect a musical instrument etc.
Nominal output level -28–+4 dBu
Headroom +18 dB
Supported plugs:
1/4-inch TRS phone type
(balanced)
1/4-inch phone type
(unbalanced)
14 O (USB) port
Connect this to a computer that supports USB 2.0.
Before connecting the Super UA for the rst time, you must
install the driver as described in “Install the Driver.
Breakout box,
Front panel
Breakout box,
Rear panel
15 16
17
Main unit, rear panel
17
Switching the 48 V phantom power on/o
1
2
Either one
Hold down
Long-press
Dynamic mic Connect with the 48 V indicator (phantom power) turned o.
* You must be sure to turn o the 48 V indicator.
Condenser mic Connect with the 48 V indicator (phantom power) turned on.
The 48 V indicator is on when 48 V phantom
power is being supplied.
15 MIC 1, 2 jacks
These are analog audio input jacks.
Nominal output level -60– -2 dBu
Headroom +18 dB
16 LINE OUT B jacks
Connect these to your monitor speakers etc.
Nominal output level +4 dBu (balanced)
Headroom +18 dB
17 48 V indicators This is lit when phantom power is being supplied.
This instrument is equipped with balanced (LINE IN, LINE OUT A jacks: TRS), (MIC 1, 2,
LINE OUT B jacks: XLR) type jacks. Wiring diagrams for these jacks are shown below.
Make connections after rst checking the wiring diagrams of other equipment you
intend to connect.
MIC 1, 2 jacks LINE OUT B jacksLINE IN, LINE OUT A jacks
Recording in stereo with two mics
1
The sensitivity is
stereo-linked
Press simultaneously
Lit green
Turning the Power On
Once everything is properly connected, be sure to follow the procedure below to turn on
their power. If you turn on equipment in the wrong order, you risk causing malfunction or
equipment failure.
1. Connect the AC adaptor.
2. Use a USB cable to connect the Super UA to your computer.
The power of the Super UA turns on.
* This unit is equipped with a protection circuit. A brief interval (a few seconds) after
turning the unit on is required before it will operate normally.
3. Turn on the power of the equipment that’s connected to the input/output jacks.
4. Adjust the volume.
* Before turning the unit on/o, always be sure to turn the volume down. Even with the
volume turned down, you might hear some sound when switching the unit on/o.
However, this is normal and does not indicate a malfunction.
Main Specications
Roland Super UA (UA-S10): USB Audio Interface
Power Supply AC Adaptor
Current Draw 1,000 mA
Dimensions
115 (W) x 161 (D) x 44 (H) mm, 4-9/16 (W) x 6-3/8 (D) x 1-3/4 (H) inches
(main unit)
136 (W) x 65 (D) x 42 (H) mm, 5-3/8 (W) x 2-9/16 (D) x 1-11/16 (H)
inches (breakout box) (excluding cord)
Weight 490 g, 1 lb 2 oz (main unit)
360 g, 13 oz (breakout box)
Accessories Owners Manual, Leaet “USING THE UNIT SAFELY, AC adaptor, USB
cable
* In the interest of product improvement, the specications and/or appearance of this unit
are subject to change without prior notice.
Owners Manual
UA-S10


Specyfikacje produktu

Marka: Roland
Kategoria: nieskategoryzowany
Model: Super UA

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Roland Super UA, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje nieskategoryzowany Roland

Roland

Roland GK-KIT-BG Instrukcja

12 Września 2024
Roland

Roland MVS-12 Instrukcja

12 Września 2024
Roland

Roland V-800HD Instrukcja

12 Września 2024
Roland

Roland XI-DANTE Instrukcja

12 Września 2024
Roland

Roland XI-REAC Instrukcja

12 Września 2024
Roland

Roland S-4000M Instrukcja

12 Września 2024
Roland

Roland CB-37SY Instrukcja

12 Września 2024
Roland

Roland SO-AES4 Instrukcja

12 Września 2024
Roland

Roland TD-12K Instrukcja

12 Września 2024
Roland

Roland CB-CS2 Instrukcja

12 Września 2024

Instrukcje nieskategoryzowany

Najnowsze instrukcje dla nieskategoryzowany

Meec Tools

Meec Tools 010-084 Instrukcja

6 Października 2024
Outwell

Outwell Scenic Road 250 Instrukcja

5 Października 2024
Impact

Impact QuikBalance Instrukcja

4 Października 2024
Impact

Impact CA-112 Instrukcja

4 Października 2024
Impact

Impact LS-BHA Instrukcja

4 Października 2024
Impact

Impact LKB-5C Instrukcja

4 Października 2024
Impact

Impact RST-001 Instrukcja

4 Października 2024