Instrukcja obsługi Rockford Fosgate 3SIXTY.3

Rockford Fosgate Konwerter audio/wideo 3SIXTY.3

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Rockford Fosgate 3SIXTY.3 (28 stron) w kategorii Konwerter audio/wideo. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/28
Serial Number: Date of Purchase:
Installation & Operation
INTERACTIVE
SIGNAL PROCESSOR
3SIXTY.3
Quick Setup Guide
1. Install 3Sixty.3 software
2. Open 3Sixty.3 Software (See pg 9)
3. Connect 3Sixty.3 USB cable to 3Sixty.3 and then to the PC. (See pg 9)
4. Open the 3Sixty.3 user interface (UI). A pop up window will appear telling you the unit is not configured.
Click “OK” (See pg 10)
5. If the configuration pop up window above does not appear telling you that the unit is not configured,
open the “Device” tab and select “Configuration” in the top left corner. (See pg 9)
6. When the input configuration page appears, select your source interface type and label your input
channels. Click “Next” (See pg 15)
7. When the output configuration page appears, label your output channels if one or more channels is not
being used select “Not Connected”. Click “Next” (See pg 15)
8. When the input channel summing page appears, select the output channel from the vehicle illustration,
then select the input(s) you would like to use/sum to create that output channel. After assigning ALL
output channels there inputs, Click “Next” (See pg 15)
9. When the assign source presets page appears, select the preset(s) you would like to assign to each
source. Click “Next” (See pg 16)
10. When the input level setup prompt appears, insert the 3Sixty.3 setup disk and play track #1 at max
volume and follow the on screen directions. Click “Next”(Outputs will be muted) (See pg 16)
11. When the adjust source level appears, reduce the volume of the source until all the level meters are
green. Click “Next” (The 3Sixty.3 is not looking for a hard clipped signal you would typically see when
level setting an amplifier) (Make a note of the MAXIMUM volume level on the source unit achieved
keeping the level meters green for future steps) (See pg16)
12. When the input attenuator controls appears, select “Auto Range” to automatically match the input
voltage, to the input voltage range of the DSP. (See pg 16)
13. a) If using a low level input, the mute warning page will appear prompting you to reduce your
volume. Click “Finish” and go to Step #15 (See pg 17)
b) If using a high level input, the input denormalization setup prompt appears, use the 3Sixty.3 setup
disk and play track #2 at half of the noted source volume in step #11. Click “Next” (See pg 17)
14. During the input normalization page, select “Auto Normalize”. This may take up to 5 min. Once
completed, Click “Next” (See pg 17)
15. The mute warning page will appear prompting you to reduce your volume, and Click “Finish”. Device
setup is now complete. Please proceed with system tuning.
16. Select the crossover type, class, slope, and frequencies for each channel. (See pg 13 & 21)
17. Level set the amplifiers to the main source unit, then adjust each additional source level. (See pg 14
& 22)
18. Select the time delay for each channel. (See pg 14 & 28)
19. Adjust the EQ for each channel, for each source or preset. (See pg 14 & 28)
20. After adjusting the EQ, level set the amplifiers to the main source unit, then adjust each additional
source level. (See pg 22)
21. Under the ”File” tab select “Save File”. (See pg 10)
2
Dear Customer,
Congratulations on your purchase of the world’s finest brand of car audio signal
processors. At Rockford Fosgate we are fanatics about musical reproduction at
its best, and we are pleased you chose our product. Through years of engineering
expertise, hand craftsmanship and critical testing procedures, we have created a
wide range of products that reproduce music with all the clarity and richness you
deserve.
For maximum performance we recommend you have your new Rockford Fosgate
product installed by an Authorized Rockford Fosgate Dealer, as we provide special-
ized training through Rockford Technical Training Institute (RTTI). Please read
your warranty and retain your receipt and original carton for possible future use.
Great product and competent installations are only a piece of the puzzle when
it comes to your system. Make sure that your installer is using 100% authentic
installation accessories from Rockford Fosgate in your installation. Rockford Fos-
gate has everything from RCA cables and speaker wire to power wire and battery
connectors. Insist on it! After all, your new system deserves nothing but the best.
To add the finishing touch to your new Rockford Fosgate image order your Rock-
ford accessories, which include everything from T-shirts to jackets.
Visit our web site for the latest information on all Rockford products;
www.rockfordfosgate.com
or, in the U.S. call 1-800-669-9899 or FAX 1-800-398-3985. For all other countries, call
+001-480-967-3565 or FAX +001-480-966-3983.
Table of Contents
If, after reading your manual, you still have questions regarding this prod-
uct, we recommend that you see your Rockford Fosgate dealer. If you need
further assistance, you can call us direct at . Be sure to 1-800-669-9899
have your serial number, model number and date of purchase available
when you call.
Safety
This symbol with “WARNING” is intended
to alert the user to the presence of important
instructions. Failure to heed the instructions
will result in severe injury or death.
This symbol with “CAUTION” is intended to
alert the user to the presence of important
instructions. Failure to heed the instructions
can result in injury or unit damage.
•To prevent injury and damage to the unit, please read and follow the
instructions in this manual. We want you to enjoy this system, not get
a headache.
•If you feel unsure about installing this system yourself, have it installed
by a qualified Rockford Fosgate technician.
•Before installation, disconnect the battery negative (-) terminal to
prevent damage to the unit, fire and/or possible injury.
Contents of Carton
•3Sixty.3 Interactive Signal Processor
•Bluetooth Dongle
•Remote Level(s) Controller
•Remote Level Control Cable (20ft)
•Power Connector (4 pin)
•High Level Input Connection (16 pin)
• Installation & Operation Manual
•Multimedia Setup Disc (CD)
•USB cable (20ft)
Introduction
©2011 Rockford Corporation. All Rights Reversed. ROCKFORD FOSGATE, PUNCH, and associated logos where applicable are registered trademarks of Rockford
Corporation in the United States and/or other countries. All other trademarks are the property of their respective owners. Specifications subject to change without notice.
PRACTICE SAFE SOUND
Continuous exposure to sound pressure levels over 100dB may cause
permanent hearing loss. High powered auto sound systems may
produce sound pressure levels well over 130dB. Use common sense
and practice safe sound.
2 Introduction
3 Specifications
4-5 Design Features
6-9 Installation
Installation Considerations
Input Connections
Remote Connections
Output Connections / Software Installation
9-11 Initial Setup
File / Device Tabs
Presets / Preferences
12-14 EQ Setup
EQ Controls
EQ Controls
15-17 High Level Sample System
18-20 Low Level Sample System
21-23 EQ Sample System
24 Final Setup
25 Troubleshooting
26 Troubleshooting Noise
27 Limited Warranty Information
28 Quick Setup Guide
3
Operating Voltage 9 - 16 VDC
Recommended Fuse 2 A
Max REM Out Current 1 A
Input Impedance (Low Level) 10K Ohm
High Level Turn On DC Voltage 4 - 16 VDC
Input Sensitivity
Low Level (RCA) 0.1V - 2V
High Level 0.1V - 28V
AUX 0.1 - 1V
Frequency Response 20 - 20K +/- 0.5dB
Max Output Voltage 8 VAC @ 0.1% THD
THD+N <0.01 @ 1KHz
Signal to Noise Ratio (RCA) >105 dBA (A weighted)
Signal to Noise Ratio (Optical) >110 dBA (A weighted)
Signal to Noise Ratio (AUX) >105 dBA (A weighted)
Common Mode Rejection Ratio >70
Channel Separation >73dB @ 1KHz
Specications
CEA 2006
Measurements on Rockford Fosgate processors conform to CEA-2006 industry standards.
Channel Front Front2 Rear Sub
Interval (oct) Adjustable
Bands 31 31 31 31
Delay 0 - 10 msec
Q Range 0.1 - 6.0
Frequency 20 -20KHz
Presets Assignable 4
Crossover Setting AP/HP/LP/BP/Shelf
Slope (dB/oct) 12 / 24 / 36 / 48
Range (Hz) 20 - 20kHz
Class Linkwitz / Bessel / Butterworth / Chebychev
Length 5.0” 12.75 cm
Width 9.3” 23.6 cm
Height 1.7” 4.3 cm
Technical Specifications
Dimensions
Crossover
Equalizer
9.3"
(23.6)
5.0"
(12.75)
1.7"
(4.3)
RESET
WIRELESS
USB RFLINK ACC OPT IN
FRONT FRONT2 REAR SUB
OUTPUTS
UNBALANCED
BALANCED
L
R
1
3
2 4
5
6
7
8

Specyfikacje produktu

Marka: Rockford Fosgate
Kategoria: Konwerter audio/wideo
Model: 3SIXTY.3

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Rockford Fosgate 3SIXTY.3, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Konwerter audio/wideo Rockford Fosgate

Rockford Fosgate

Rockford Fosgate RF-HLC4 Instrukcja

29 Września 2024
Rockford Fosgate

Rockford Fosgate 3SIXTY.3 Instrukcja

29 Września 2024

Instrukcje Konwerter audio/wideo

Najnowsze instrukcje dla Konwerter audio/wideo

Abus

Abus TVAC20001 Instrukcja

10 Października 2024
StarTech.com

StarTech.com VS123HD Instrukcja

9 Października 2024
StarTech.com

StarTech.com VS421HDDP Instrukcja

9 Października 2024
StarTech.com

StarTech.com ST228MX Instrukcja

9 Października 2024
StarTech.com

StarTech.com HDMI2DVI Instrukcja

9 Października 2024
StarTech.com

StarTech.com VGANTSCPRO Instrukcja

9 Października 2024
StarTech.com

StarTech.com CPNT2VGAA Instrukcja

9 Października 2024
StarTech.com

StarTech.com DVI2VGA Instrukcja

9 Października 2024
StarTech.com

StarTech.com VS222HDQ Instrukcja

9 Października 2024
StarTech.com

StarTech.com VS122HDMIU Instrukcja

9 Października 2024