Instrukcja obsługi RIKON 30-240
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla RIKON 30-240 (24 stron) w kategorii Wiertarka. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/24
www.rikontools.com
30-240M6
20 Floor Drill Press ”
Operator’s Manual
Record the serial number and date of purchase in your manual for future reference.
Serial Number: _________________________ Date of purchase: _________________________
For technical support or parts questions, email techsupport@rikontools.com or call toll free at (877)884-5167
The serial number can be found on the specication label on the rear of your machine.
2
TABLE OF CONTENTS
SPECIFICATIONS
NOTE: The specications, photographs, drawings and information in this manual represent the current model when the
manual was prepared. Changes and improvements may be made at any time, with no obligation on the part of Rikon
Power Tools, Inc. to modify previously delivered units. Reasonable care has been taken to ensure that the information in
this manual is correct, to provide you with the guidelines for the proper safety, assembly and operation of this machine.
Motor ................................................................................................... 1 HP, TEFC
Motor Speed (no load).......................................................................... 1,720 RPM
Volts ............................................................................................................. 120 V
Amps, Hertz ..................................................................................... 13.5 A, 60 Hz
Swing ................................................................................................................ 20”
Chuck Size ............................................................................ 5-20mm (7/32-3/4”)
Chuck Taper .................................................................................................... JT3
Drilling Capacity ................................................................................................. 1”
Spindle Travel .............................................................................................. 4-3/4”
Spindle Taper .................................................................................................. MT3
Head Rotates ................................................................................................. 360°
Speed Range (RPM) ........................................................................... 180 - 3865
Speeds .............................................................................................................. 12
Quill Diameter ....................................................................................... 3” (75mm)
Table Size ................................................................................... 16-3/4” x 18-3/4”
Table Tilts ..................................................................................... 90° Left & Right
Table Rotates ................................................................................................. 360°
Maximum Chuck to Table ........................................................................... 24-1/4”
Maximum Chuck to Base ........................................................................... 43-3/4”
Column Diameter ............................................................................ 3-5/8” (92mm)
Height ............................................................................................................... 67”
Base Size .................................................................................... 22-3/4” x 17-1/2”
Net Weight ................................................................................................ 250 lbs.
Specications.....................................................................................................................2
Safety Instructions ........................................................................................................3 - 6
Contents of Package .....................................................................................................7
Getting To Know Your Machine ..............................................................................................8
Installation ......................................................................................................................8
Assembly .................................................................................................................... 9 - 12
Adjustments...............................................................................................................12 - 15
Operation .......................................................................................................15
Maintenance ....................................................................................................................16
Electricals & Wiring Diagram .......................................................................................5 & 16
Troubleshooting .........................................................................................................17
Parts Diagrams .........................................................................................................18 - 20
Parts List ................................................................................................................21
Accessories ..........................................................................................................22
Notes ..........................................................................................................................22
Warranty ..........................................................................................................................23
3
SAFETY SYMBOLS
IMPORTANT! Safety is the single most important consideration in the operation of this equipment. The following
instructions must be followed at all times. Failure to follow all instructions listed below may result in electric shock,
re, and/or serious personal injury.
There are certain applications for which this tool was designed. We strongly recommend that this tool not be modied
and/or used for any other application other than that for which it was designed. If you have any questions about its
application, do not use the tool until you have contacted us and we have advised you.
SAFETY INSTRUCTIONS
GENERAL SAFETY
KNOW YOUR POWER TOOL. Read the owner’s manual
carefully. Learn the tool’s applications, work capabilities,
and its specic potential hazards.
BEFORE USING YOUR MACHINE
To avoid serious injury and damage to the tool, read and
follow all of the Safety and Operating Instructions before
operating the machine.
1. Some dust created by using power tools contains
chemicals known to the State of California to cause cancer,
birth defects, or other reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks, cement, and other
• masonry products.
• Arsenic and chromium from chemically treated lumber.
Your risk from these exposures varies, depending on how
often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area and work
with approved safety equipment, such as those dust masks
that are specially designed to lter out microscopic
particles.
2. the entire Owner’s Manual. how to use READ LEARN
the tool for its intended applications.
3. If the tool is supplied with a 3 GROUND ALL TOOLS.
prong plug, it must be plugged into a 3-contact electrical
receptacle. The 3rd prong is used to ground the tool and
provide protection against accidental electric shock. DO
NOT remove the 3rd prong. See Grounding Instructions
on the following pages.
4. AVOID A DANGEROUS WORKING ENVIRONMENT.
DO NOT use electrical tools in a damp environment or
expose them to rain.
5. use electrical tools in the presence of DO NOT
ammable liquids or gases.
6. ALWAYS keep the work area clean, well lit, and
organized. work in an environment with oor DO NOT
surfaces that are slippery from debris, grease, and wax.
7. KEEP VISITORS AND CHILDREN AWAY. DO NOT
permit people to be in the immediate work area,
especially when the electrical tool is operating.
8. to perform an operation DO NOT FORCE THE TOOL
for which it was not designed. It will do a safer and
higher quality job by only performing operations for
which the tool was intended.
9. wear loose WEAR PROPER CLOTHING. DO NOT
clothing, gloves, neckties, or jewelry. These items can
get caught in the machine during operations and pull the
operator into the moving parts. The user must wear a
protective cover on their hair, if the hair is long, to
prevent it from contacting any moving parts.
10. CHILDPROOF THE WORKSHOP AREA by
removing switch keys, unplugging tools from the
electrical receptacles, and using padlocks.
11. ALWAYS UNPLUG THE TOOL FROM THE
ELECTRICAL RECEPTACLE when making adjust-
ments, changing parts or performing any maintenance.
SAFETY ALERT SYMBOL: Indicates DANGER, WARNING, or CAUTION. This symbol may be used
in conjunction with other symbols or pictographs.
Indicates an imminently hazardous situation, which, if not avoided, could result in death or
serious injury.
Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious
injury.
Indicates a potentially hazardous situation, which, if not avoided, could result in minor or
moderate injury.
NOTICE: Shown without Safety Alert Symbol indicates a situation that may result in property damage.
Specyfikacje produktu
| Marka: | RIKON |
| Kategoria: | Wiertarka |
| Model: | 30-240 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z RIKON 30-240, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Wiertarka RIKON
27 Grudnia 2024
27 Grudnia 2024
27 Grudnia 2024
27 Grudnia 2024
27 Grudnia 2024
27 Grudnia 2024
30 Września 2024
Instrukcje Wiertarka
- Wiertarka AEG
- Wiertarka Worx
- Wiertarka Kawasaki
- Wiertarka Milwaukee
- Wiertarka Bosch
- Wiertarka Yato
- Wiertarka Parkside
- Wiertarka Global
- Wiertarka Toolcraft
- Wiertarka Festool
- Wiertarka Panasonic
- Wiertarka Bavaria By Einhell
- Wiertarka Stanley
- Wiertarka Black & Decker
- Wiertarka Scheppach
- Wiertarka Proxxon
- Wiertarka Ribimex
- Wiertarka Hazet
- Wiertarka DeWalt
- Wiertarka Einhell
- Wiertarka Genesis
- Wiertarka Hyundai
- Wiertarka Silverline
- Wiertarka Makita
- Wiertarka Ozito
- Wiertarka RYOBI
- Wiertarka Flex
- Wiertarka GO/ON
- Wiertarka DEDRA
- Wiertarka Baumr-AG
- Wiertarka Biltema
- Wiertarka Hilti
- Wiertarka BaseTech
- Wiertarka Max Bahr
- Wiertarka Trotec
- Wiertarka Dremel
- Wiertarka Handwerk
- Wiertarka Velleman
- Wiertarka Meec Tools
- Wiertarka Güde
- Wiertarka Bavaria
- Wiertarka Cecotec
- Wiertarka Zipper
- Wiertarka Mafell
- Wiertarka Delta
- Wiertarka DURO PRO
- Wiertarka McKenzie
- Wiertarka Westfalia
- Wiertarka Ergotools Pattfield
- Wiertarka Fein
- Wiertarka Ferm
- Wiertarka Hitachi
- Wiertarka Herkules
- Wiertarka Craftsman
- Wiertarka Fieldmann
- Wiertarka Ridgid
- Wiertarka PowerPlus
- Wiertarka Alpha Tools
- Wiertarka Vonroc
- Wiertarka Powerfix
- Wiertarka HiKOKI
- Wiertarka Workzone
- Wiertarka Porter-Cable
- Wiertarka Metabo
- Wiertarka Cotech
- Wiertarka Skil
- Wiertarka Kinzo
- Wiertarka Tryton
- Wiertarka Sun Joe
- Wiertarka Tacklife
- Wiertarka Luxor
- Wiertarka Maktec
- Wiertarka Steren
- Wiertarka Bort
- Wiertarka Tanaka
- Wiertarka Malmbergs
- Wiertarka Power Craft
- Wiertarka Eibenstock
- Wiertarka Topcraft
- Wiertarka Festo
- Wiertarka Sparky
- Wiertarka Gamma
- Wiertarka Carat
- Wiertarka Kress
- Wiertarka Duro
- Wiertarka Berner
- Wiertarka Varo
- Wiertarka Defort
- Wiertarka Max
- Wiertarka Truper
- Wiertarka Bruder Mannesmann
- Wiertarka Powerblade
- Wiertarka Meister Craft
- Wiertarka Rupes
- Wiertarka Batavia
- Wiertarka Protool
- Wiertarka Economy
- Wiertarka Holzmann
- Wiertarka Graphite
- Wiertarka Huvema
- Wiertarka Black Decker
- Wiertarka Stomer
- Wiertarka Elu
- Wiertarka Fe Powertools
- Wiertarka Blucave
- Wiertarka Ecomac
- Wiertarka Lux Tools
- Wiertarka Kreg
- Wiertarka Sthor
- Wiertarka Verto
- Wiertarka Wurth
- Wiertarka Spit
- Wiertarka King Craft
- Wiertarka Rok
- Wiertarka Profitech
- Wiertarka Narex
- Wiertarka Baier
- Wiertarka RUKO
- Wiertarka Toolson
- Wiertarka Felisatti
- Wiertarka Robust
- Wiertarka Einhell Bavaria
- Wiertarka MyTool
- Wiertarka G-Technology
- Wiertarka Stalco
- Wiertarka Total
- Wiertarka Netter Vibration
Najnowsze instrukcje dla Wiertarka
28 Grudnia 2024
28 Grudnia 2024
28 Grudnia 2024
28 Grudnia 2024
28 Grudnia 2024
27 Grudnia 2024
27 Grudnia 2024
27 Grudnia 2024
27 Grudnia 2024
27 Grudnia 2024