Instrukcja obsługi RGBlink DXP V1616

RGBlink przełącznik DXP V1616

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla RGBlink DXP V1616 (3 stron) w kategorii przełącznik. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/3

DXP V1616 –Quick Start

Installation and cabling features

Rear Panel

Connections

2VGA Output

Step 1-Mounting

Turn off or disconnect all equipment power sources.

Step 4-RS232 In

DXP V1616 Quick Start

Rev 1.0

Page 1 of 3

Address: S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone, Xiamen, Fujian Province, P.R.C

Tel: 00865925771197 Fax:00865925771202

Email: sales@rgblink.com http://www.rgblink.cn

VGA Input RS232 OUT

Power Switch

Step 3-VGA Output

VIEW SIZE THE WORLD

NOTE

This guide provides quick start instructions for an experienced installer

to set up and operate the DXP V1616.

For full installation, configuration, and operation details, please refer to

the DXP V1616 user manual, which is available at www.rgblink.com.

3RS232 IN Power IEC-3 port

Step 2-VGA Input

Use to input VGA signal from VGA

player or computer with VGA connector.

Function Button

Step 5-RS232 Out

Connect to the monitor, projector and

so on.

Connecting serial communication interface of RS232

control protocol, can connect central control device,

such as CP 2048.

Serial communication interface of multiple devices

cascading control, can connect many sets of DXP

devices.

Step 6-Power

Plug in power cord which has IEC connector, DXP

V1616 supports AC power from 85 to 264V, 50-60Hz,

which means world wide compatible.

Power On

Push power switch to ON position. LCD module on the

front panel will show RGBLINK and DXP V1616

model information, and go into self verification. For the

first setup, it is default for factory setting. User can

operate DXP V1616 through the menus on LCD panel.

Local Control Front Panel Operation

【】【】0 ~ 9 Digital button: selection button for

input and output channel, used to set video signal

input and output channel, also, can be used to number

choice of save or call saving modes.

【】0 button can also be used to shut down

the channel output.

NOTE

【】【】【】10+ , 20+ , 30+ +system function button,

means decimal.

NOTE 【】20+ can be used as UP arrow keys;

【】30+ can be used as DOWN arrow keys.

【】ALL Used as distributor selection, can set a

certain input to all outputs.

【】F1 Fast call user save mode 1;

【】F2 Fast call user save mode 2;

【】Menu Related menu includes: STATUS, RESET,

MATRIX, LOGO.

【】Mode Audio and video switching key, used to

select 3 modes, such as "Audio and video sync

switching AV", "Audio switching A", "Video

switching V", it is default for "Audio and video sync

switching AV".

【】Enter Confirm button, when functional input is

confirm button, and press Enter before enter 【】

menu, it displays the current input/output state, "/"

means empty, and not choose input signal source.

【】【】20+ , 30+ function reuse button:

Push Menu to enter the menu, press 20+ UP 【】【】

arrow keys, 30+ DOWN arrow keys, and select 【】

the menu option.

DXP V1616 Quick Start

Rev 1.0

Page 2 of 3

Address: S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone, Xiamen, Fujian Province, P.R.C

Tel: 00865925771197 Fax:00865925771202

Email: sales@rgblink.com http://www.rgblink.cn

How to set one-to-one correspondence for

input and output way

1. Press button Rec on front panel;【】

2. Press button 0 on front panel;【】

3. Press Enter to confirm.【】

How to switch from one input to all outputs

1. Press button on front panel, for example, choose 2 ;【】

2. Press ALL , and finish switching input2 to all 【】

outputs.

Also, you can get the same operation effect by the

following ways:

1. Press button on front panel, for example, choose

【】ALL ;

2. Choose input way, for example, button 2 ;【】

3. Press Enter to confirm.【】

How to save pre-set input and output way

1. Press button Save on front panel;【】

2. Can select 24 modes from button 1 ~ 24 , 【】【】

for example, choose button 2 ;【】

3. Press Enter to confirm.【】

NOTE Input way: currently connect way for

switching signal;

Output way: the connect way of peripheral display

device.

【】【】1 ~ 9 button on the panel means way1 to way9.

Way above 10 can be selected combined 10+ with【】

【】【】0 ~ 6 button.

How to factory reset

How to read device related information

How to switch between input and output way

DXP V1616 can rapidly switch any way signals by front

panel buttons, specific operations are as follows:

1. Press front panel number button, select the input way,

such as choosing 3 for input way;【】

2. Press again front panel number button, select the

output way, such as choosing 5 for output way;【】

3. After selection, press Enter to confirm.【】

【】Rec Call saving mode selection key, can call saving

user mode, range for: 0 ~ 24 , a total of 25 【】【】】

kinds of call saving mode.

【】Save Saving modes selection key, can save all

current switching channels and current states, range for:

【】【】 1 ~ 24 , a total of 24 kinds of saving modes.

If power fails suddenly, the device will

automatically save to the current using mode,

and do not need reset when power on again.

NOTE

【】Esc The button exits the current state to the top

level state.

How to close one output way

1. Press button 0 on front panel;【】

2 .Choose output way, for example, button 8 ;【】

3. Press Enter to confirm.【】

How to close all output ways

1. Press button 0 on front panel;【】

2. Press button ALL on front panel. 【】

Also, you can get the same operation effect by the

following way:

1. Press button ALL on front panel;【】

2. Press button 0 on front panel;【】

3. Press Enter to confirm.【】

How to call pre-set input and output way

saving mode

1. Press button Rec on front panel;【】

2. Can select 25 modes from button 0 ~ 24 , 【】【】

for example, choose button 7 ;【】

3. Press Enter to confirm.【】

NOTE 【】O is default for one-to-one correspondence

for input and output way. That is input 1 is 【】

corresponding to output 1 , input 2 is 【】【】

corresponding to output 2 …【】

1. Press button Menu on front panel;【】

2. Press button 30+ 30+ reuse for DOWN 【】（【】

arrow key, button 20+ reuse for UP arrow 【】

key , make RESET option for selected state;）

3. Press Enter to confirm and enter the 【】

initialization interface;

4. Press any key according to the LCD hint and

complete factory reset.

1. Press button Menu on front panel;【】

2. It is default for STATUS option, if it is not selected,

press 30+ or 20+ Now 30+ reuse【】【】（【】

for DOWN arrow key, button 20+ reuse for 【】

UP arrow key and select STATUS;）

3. Press Enter to confirm, read the information【】

by button 30+ DOWN arrow key or button【】

【】20+ UP arrow key.

How to set LOGO display when power on

1. Press button Menu on front panel;【】

2. Press 30+ or 20+ Now 30+ reuse【】【】（【】

for DOWN arrow key, button 20+ reuse for 【】

UP arrow key and select LOGO;）

3. Press Enter to confirm, and enter LOGO 【】

switch setting, LOGO ON or OFF at boot can be

set.

Address: S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone, Xiamen, Fujian Province, P.R.C

Tel: 00865925771197 Fax:00865925771202

Email: sales@rgblink.com http://www.rgblink.cn

DXP V1616 Quick Start

Rev 1.0

Page 3 of 3

Common Questions and Solution

1. When there is double image in matrix peripheral

display device images, for example, the projector

has double image, generally, it is not caused by

the host:

● Maybe the projector is not adjusted probably or the

wire quality is not standard, adjusting the projector

button or replacing the wire is needed.

● Maybe the wire is too long and cause signal

attenuation, adding a long wire drive is needed.

● Maybe hybrid installation with the 220V high voltage.

2. When there is color loss or no video signal output,

maybe it is caused by poor contact of video

interface or break.

3. When COM (generally refers to: computer serial

port) can not control the matrix, check if the

communication port that controls software set is

corresponding to device serial port; Check if the

computer communication port is in good

condition.

4. No corresponding image output when matrix

switching:

● Check if the corresponding input has any signals, (or

test with oscilloscope or multimeter). If there is no

signal input, may be the input connection is broken or

joint is loose, you can replace the connecting line.

● Check if the corresponding output end has any

signals, (or test with oscilloscope or multimeter) if

there is no signal output, may be the input connections

is broken or joint is loose, you can replace the

connecting line.

● Check if the output port is in accord with the

controlled port.

● If not belong to above three circumstances, maybe it

is caused by host internal fault, please send to

professional for maintenance.

5. If there is no display in LCD and no reaction for

operation, please check if the power input is good

contacts.

6. If the output image is disturbed, maybe the

input/output devices without good ground.

7. If there is obvious electrostatic when drawing or

inserting audio and video interface, maybe the

power ground without good ground, please ground

with the right way, otherwise, it will easily damage

the host and shorten the host life.

8. LCD display is normal, communication port

has return code, but no image output or no

audio output:

● Maybe the AV interface is loose, you can just plug

it tightly;

● Maybe it is short connection, you can just change

it;

● Maybe wire is broken, you can just change it.

9. If matrix panel button, communication port can

not be controlled, maybe host internal is

damaged, please send to professional for

maintenance.

Specyfikacje produktu

Marka:	RGBlink
Kategoria:	przełącznik
Model:	DXP V1616

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z RGBlink DXP V1616, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje przełącznik RGBlink

RGBlink DXP V0808 Instrukcja

29 Września 2024

RGBlink DXP D0404 Instrukcja

3 Sierpnia 2024

RGBlink DXP V1616 Instrukcja

3 Sierpnia 2024

Instrukcje przełącznik

Najnowsze instrukcje dla przełącznik

Intermatic P1101 Instrukcja

20 Marca 2025

AirLive IG-641RPOE Instrukcja

12 Marca 2025

AirLive IGM-1082RBT Instrukcja

12 Marca 2025

APC AP7532 Instrukcja

10 Marca 2025

Lancom GS-3628XP Instrukcja

10 Marca 2025

Advantech EKI-9510E-2GMPW-B Instrukcja

10 Marca 2025

Theben ELPA 9 Instrukcja

5 Marca 2025

Digitus DN-80113-2 Instrukcja

27 Lutego 2025

Leviton 47611-C6B Instrukcja

25 Lutego 2025

Yamaha SWX2322P-16MT Instrukcja

22 Lutego 2025