Instrukcja obsługi Revox V218

Revox nieskategoryzowany V218

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Revox V218 (2 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 10 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

C18 Multiuser Wall Control

With the C18 Multiuser Wall Control, commands (IR triggers) can be sent to the Multiuser

system that are stored in the Multiuser Server. The function is defined in the Configurator

itself. In addition, a different behaviour can be defined between a short and a long

keystroke.

Via the integrated IR receiver (to the left of the power button), infrared codes (RC5) can be

received from IR remote controls and forwarded to the Multiuser System for IR triggers.

With the help of the DIL switches on the back of the wall-mounted keypad, different RC5

addresses can be selected in case of IR conflicts with other remote controls/devices.

Command overview

Code page option for C18 wall-mounted keypad available from SW version 1.00 onwards

** RC5 code is combined with current user/source address, i.e. if user 2 (address 21) was selected last, e.g. the volume_up

command is also assigned address 21 and an RC5 command [21] [16] is sent.

Checking of RC5 command

The defined RC5 codes can be checked through the display on the Multiuser amplifier M30 or V219. The infrared mode

can be selected with its Setup button, the received signals from the IR Link inputs can be detected and its RC5 address and

command can be displayed.

IR display of the Multiuser amplifier M30 or V219

DIL switch

With the introduction of SW version 218-2 1.00 (Multiuser Programmer Software), there is a code page option for the C18

Multiuser Wall Control. 4 different code pages can be selected via DIL switches 3 and 4 on the back of the C18 wall keypad.

To do this, dismantle the wall control and remove the plastic cover on the back. The desired code page can now be set

with a small screwdriver. Please observe the current ESE regulations when the cover is open so as not to damage the

electronics.

Button

Description

Code

Page 1

Code

Page 2

Code

Page 3

Code

Page 4

User Favorit 1

Short keystroke: last favorit of User 1

L keystrokeong : favorit no. 1 User 1 of

[17] [63]

[24] [63]

[25] [63]

[26] [63]

User Favorit 2

Short keystroke: last favorit of User 2

Long keystroke: favorit . 1 no of User 2

[20] [63]

[24] [55]

[25] [55]

[26] [55]

User 1

Select User 1

[07] [63]

[24] [56]

[25] [56]

[26] [56]

User 2

Select User 2

[21] [63]

[24] [57]

[25] [57]

[26] [57]

Local Input

Select local analogue input of the user

[19] [63]

[24] [51]

[25] [51]

[26] [51]

Track_down

[ ] [ ] ** 33

[24] [19]

[25] [19]

[26] [19]

Track_up

[ ] [ ] ** 32

[24] [18]

[25] [18]

[26] [18]

Volume_down

[ ] [ ] ** 17

[24] [21]

[25] [21]

[26] [21]

Volume_up

[ ] [ ] ** 16

[24] [20]

[25] [20]

[26] [20]

Power Off

Short keystroke: switch-off room

Long keystroke: switch-off the complete system

[ ] [ ] ** 12

[24] [39]

[25] [39]

[26] [39]

RC5-Codes C18 Multiuser Wall Remote

Cabeling

The C18 wall control unit is connected to the Multiuser amplifier via a 3-pole screwable connector. When wiring, make

sure that the shielding of a CAT cable (S/FTP, F/FTP) is connected to the GND line on both sides. In addition, a pair of wires

for one signal should be connected together. Both measures increase the cable cross-section and thus reduce the voltage

drop in the cable. With this cabling variant, cable lengths of up to 100 m can be realised. Alternatively, a data cable of type

U72 (1x4x0.5 mm2) can be used.

Parallel operation

In larger rooms, it may make sense to place two C18 wall-mounted keypads at different locations in the room. 2 C18s may

be operated in parallel, i.e. all 3 signal lines (GND, IR, VCC) are connected in parallel.

To avoid double commands when using remote controls, if both wall-mounted keypads could receive the IR signal, it is

recommended to deactivate the IR receiver for of the two C18 wall-mounted keypads. This is set via a DIL switch (DIL one

1) on the back of the wall-mounted keypad - see illustration above.

The IR link, including the trigger-out of the multiuser amplifier, may be loaded with a maximum of 80 mA. The nominal

current requirement of a C18 is 23 mA.

Technical Data

DIL

Function

Description

Factory setting

IR eye

Intern IR receiver [1]/ off [0] al on

O n

LED

LED on [1]/ off [0]

3 + 4

RC5 Code Pages

RC5 adress combination

00: Code Page 1

01: Code Page 2

10 : Code Page 3

11: Code Page 4

Off Off [00] +

Protection class IP20, dry installation (acc. with IEC 60529)

Ambient temperature Operation -5 °C to +45 °C

Storage: -25 °C to +70 °C

Connection type Screwable plug connector

3 x 0.15 - 1.50 mm²

DIL factory settings 1: IR on

2: LED on

3: Code page 1-4

4: Code page 1-4

Cable Installation cable S/FTP or F/FTP or

U72 ABG 1 x 4 x 0.5 mm² creened) (s

Maximum cable lengths Max. 100 m Multiuser amplifier M30 or V to 219

Power consumption 17 mA (passive) /

23 mA (button pressed)

Parallel operation Max. 2 wall-mounted keypads can be switched in parallel

Technische Änderungen vorbehalten.

Manual-C18 m2-en

VCC + =

IR = IR

GND = -

Specyfikacje produktu

Marka:	Revox
Kategoria:	nieskategoryzowany
Model:	V218

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Revox V218, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje nieskategoryzowany Revox

Revox KNX Gateway Instrukcja

19 Maja 2024

Revox V218 Instrukcja

9 Maja 2024

Instrukcje nieskategoryzowany

Najnowsze instrukcje dla nieskategoryzowany

Asko DBI644MIB.S.TW/1 Instrukcja

28 Października 2024

Asko DFS233IB.S.TW/1 Instrukcja

28 Października 2024

Emko EZM-9920 Instrukcja

27 Października 2024

Emko ESM-3712-H Instrukcja

27 Października 2024

Emko ATS-10 Instrukcja

27 Października 2024

Emko EAOM-11.2 Instrukcja

27 Października 2024

Emko EPM-3790 Instrukcja

27 Października 2024

Emko EPM-7790 Instrukcja

27 Października 2024

Livarno Lux IAN 108340 Instrukcja

27 Października 2024

Livarno Lux HG06009A-BS Instrukcja

27 Października 2024