Instrukcja obsługi RDL FP-TPX3A
RDL
Ręczny blender
FP-TPX3A
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla RDL FP-TPX3A (2 stron) w kategorii Ręczny blender. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/2
FLAT-PAK™ SERIES
Model FP-TPX3A
Format-A Twisted Pair
Remote Controlled Mixer
3-Channel Remote-Controlled Audio Mixer
VCA Level Control for Each Input Pair
Format-A Twisted Pair Inputs
Balanced and Unbalanced Outputs
Two Mono Unbalanced Outputs to Feed Stereo Amplifier
Inputs and Outputs on Detachable Connectors
Twisted Pair Interconnection to Remote Control
Directly Controlled by RDL Remote Controls
Two and Three Channel Remote Controls Available
Local Input Available if Only Two Twisted Pair Inputs Used
Paging Source May Connect to Local Input
Front-Panel Gain Trim Matches Active or Passive Format-A Senders
Dual-LED VU Meter Displays Mixer Output Level
Audio Presence Detector Controls Open-Collector Outputs
Detector Outputs Intended to Enable Power Amplifiers or System Power
Energy Savings Possible Using Detector Outputs
Selectable 10 or 20 Minute Detector Release Delay
The FP-TPX3A is a mono audio mixer in the convenient line of FLAT-PAK products, featuring the superior engineering and components common
to RDL products. The FP-TPX3A may be rack or surface mounted with optional FLAT-PAK series accessories. The FP-TPX3A gives you the
advantages of a quality audio mixer with the added convenience of remote control!
The FP-TPX3A is the ideal choice where a user-accessible mixer must control the volume of multiple sources in a zone. RDL Format-A
twisted pair audio senders connect directly to the mixer, allowing each user input to be balanced or unbalanced, mic or line level.
FP-TPX3A outputs are provided in balanced and unbalanced formats. Two unbalanced outputs are available to feed the mono mixer
output to a stereo amplifier input. Remote control of the mixer allows audio signals to be kept at a single equipment location. Audio is
mixed by VCA circuits that are adjusted by control signals from the remote control.
Two Format-A jacks are provided for signal inputs. If the Format-A senders are daisy-chained, only one of the input jacks is used. The
other input jack may be used to receive another Format-A sender, or may be used to loop the received Format-A signals out to additional
Format-A mixers or receivers. The FP-TPX3A provides power to all connected active senders. The FP-TPX3A is designed to mix the
three Format-A audio signals from pairs A, B and C. A front-panel switch allows the PAIR C mixer input to be fed either from the twisted
pair C input signal or from a local input. A detachable terminal block is provided to connect a local paging or music source to the
LOCAL INPUT. Note: Pair C signals are passed through both Format-A input jacks even if the mixer is set to use a local source instead of
the PAIR C twisted pair source.
Format-A senders are available in active and passive models. Passive Format-A models with unbalanced input jacks send a lower signal
level to the mixer than is sent by active senders or by passive senders with balanced inputs. Each INPUT GAIN control is calibrated to be
adjusted clockwise for an unbalanced passive sender; counter-clockwise for an active sender or passive sender with a balanced input.
A standard RDL dual-LED VU meter provides visual indication of the output level from the mixer. Each input channel operates at unity gain
when the corresponding remote control is adjusted to maximum. This assures ample headroom at all normal operating levels. The mixer
output is mono. The output is available on a single balanced detachable terminal block or on two unbalanced RCA jacks intended to
connect directly to the stereo input of a power amplifier.
The AUDIO LED illuminates whenever audio is present at the output of the mixer, defined as greater than 35 dB below +4 dBu. This
threshold triggers the AUDIO DETECT OUTPUTS. Two open collectors are provided on a detachable terminal block. One of these
terminals switches low when audio is present, and may be used to switch amplifiers or other system components on. The other terminal is
pulled low when audio is not present. It is intended for muting the digital carrier of power amplifiers equipped for remote muting. Either of
these terminals may be used to trigger a vari The use of these terminals to shut downety of other RDL modules or OEM equipment.
unused equipment can produce effective system energy and cost savings. These control terminals normally remain triggered for 10
minutes after audio is absent. The delay can be increased to 20 minutes using a ground jumper on the terminal block.
The mixer levels are set by RDL remote controls that connect directly to the FP-TPX3 through an RJ45 jack using standard twisted pair
cable. The control ports on the mixer and remote controls are color-coded light blue to distinguish them from standard Format-A jacks. The
mixer provides power to the remote control. Either a two or three channel remote control may be used. If remote mixing of only two
channels is needed, a two channel remote may be used. Pair C becomes the i motely controlled. The nput channel that is not re
PAIR C/LOCAL INPUT can be left active at unity gain, typically for a paging source, or may be disabled by a switch set during installation.
If the cable connected to the remote control he mixer output mutes. becomes disconnected, t
RDL
659 6th St.
Prescott, AZ., USA 86301
(928) 443-9391 FAX (928) 443-9392 www.rdlnet.com
TYPICAL APPLICATIONS:
► Meeting Rooms
► Boardrooms
► Classrooms
► Restaurant or Residential Patios
► Retail Stores
ASSOCIATED REMOTE CONTROL EXAMPLES:
► D-RC2 and DS-RC2 Two-channel remote controls
► D-RC2M and DS-RC2M Two-channel remote controls with muting
► D-RC3 and DS-RC3 Three-channel remote controls
► D-RC3M and DS-RC3M Three-channel remote controls with muting
FLAT-PAK™
SERIES
Model FP-TPX3A
Format-A Twisted Pair
Remote Controlled Mixer
TYPICAL PERFORMANCE
Inputs (3): RDL FORMAT-A; Balanced line level
Input Connections: RJ45 (FORMAT-A); Detachable Terminal Block (Pair C)
Outputs (3): 150 Ω balanced; 1 kΩ unbalanced (2)
Output Connections: Detachable Terminal Block (balanced); RCA Phono Jacks (unbalanced)
Output Level: +4 dBu balanced, -10 dBV unbalanced
Frequency Response: 20 Hz to 20 kHz (+/- 0.25 dB)
THD+N: < 0.05% (20 Hz to 20 kHz); <0.02% (1 kHz)
Noise below +4 dBu: < -100 dB (all channels off); <-75 dB (any channel on); <-70 dB (all channels on)
Headroom above +4 dBu: > 18 dB
CMRR: > 80 dB (50 Hz to 150 Hz)
VCA attenuation: >90 dB (each input, remote control volume off)
Indicators (3): Dual-LED VU meter (2); Audio present (threshold = 35 dB below +4 dBu output)
Power Connections (3): Terminal block; dc power jack (2)
Power Requirement: 24 Vdc @ 120 mA plus connected FORMAT-A sender currents
Overall Dimensions: Height: 1.42 in.3.61 cm
Width: 3.25 in. 8.26 cm
Length: 8.14 in. 20.68 cm
Installation/Operation
Declaration of Conformity available from rdlnet.com.
Sole EMC specifications provided on product package.
Specifications are subject to change without notice.
Radio Design Labs Technical Support Centers
U.S.A. (800) 933-1780, (928) 778-3554; Fax: (928) 778-3506
Europe [NH Amsterdam] (++31) 20-6238 983; Fax: (++31) 20-6225-287
891-2145E
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rule. These limits are designed to
provide reasonable protection against harmful interference
in a residential installation. The equipment generates,
uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off an
on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment
and receiver
Connect the equipment into an outlet on a circuit
different from that which the receiver is
connected.
Consult the dealer or an experienced radio/TV
technician for help.
Specyfikacje produktu
| Marka: | RDL |
| Kategoria: | Ręczny blender |
| Model: | FP-TPX3A |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z RDL FP-TPX3A, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Ręczny blender RDL
22 Września 2024
22 Września 2024
21 Września 2024
21 Września 2024
20 Września 2024
20 Września 2024
20 Września 2024
18 Września 2024
18 Września 2024
18 Września 2024
Instrukcje Ręczny blender
- Ręczny blender Yamaha
- Ręczny blender Electrolux
- Ręczny blender AEG
- Ręczny blender Beko
- Ręczny blender Smeg
- Ręczny blender Caso
- Ręczny blender Gorenje
- Ręczny blender Braun
- Ręczny blender Russell Hobbs
- Ręczny blender Sage
- Ręczny blender Tefal
- Ręczny blender Philips
- Ręczny blender Livoo
- Ręczny blender SilverCrest
- Ręczny blender Bosch
- Ręczny blender Brentwood
- Ręczny blender Severin
- Ręczny blender Muse
- Ręczny blender Behringer
- Ręczny blender Allen & Heath
- Ręczny blender Medion
- Ręczny blender Black & Decker
- Ręczny blender OK
- Ręczny blender Max Pro
- Ręczny blender Adler
- Ręczny blender Tesla
- Ręczny blender Westinghouse
- Ręczny blender Quigg
- Ręczny blender Domo
- Ręczny blender GE
- Ręczny blender Ardes
- Ręczny blender Taurus
- Ręczny blender Orbegozo
- Ręczny blender Vivax
- Ręczny blender Siemens
- Ręczny blender Ambiano
- Ręczny blender Grundig
- Ręczny blender Jocel
- Ręczny blender Hyundai
- Ręczny blender Silverline
- Ręczny blender Mesko
- Ręczny blender Concept
- Ręczny blender Shure
- Ręczny blender ECG
- Ręczny blender Makita
- Ręczny blender Unold
- Ręczny blender Hotpoint
- Ręczny blender Kenwood
- Ręczny blender Trisa
- Ręczny blender Zelmer
- Ręczny blender Cuisinart
- Ręczny blender Wilfa
- Ręczny blender Krups
- Ręczny blender Bomann
- Ręczny blender Moulinex
- Ręczny blender Emerio
- Ręczny blender H.Koenig
- Ręczny blender Alesis
- Ręczny blender Melissa
- Ręczny blender Beper
- Ręczny blender Morphy Richards
- Ręczny blender Instant
- Ręczny blender Fagor
- Ręczny blender Redmond
- Ręczny blender Koenic
- Ręczny blender Izzy
- Ręczny blender WMF
- Ręczny blender ProfiCook
- Ręczny blender Klarstein
- Ręczny blender BEEM
- Ręczny blender Arendo
- Ręczny blender Manta
- Ręczny blender Pyle
- Ręczny blender Cecotec
- Ręczny blender KitchenAid
- Ręczny blender AFK
- Ręczny blender Eta
- Ręczny blender Camry
- Ręczny blender Steba
- Ręczny blender Scarlett
- Ręczny blender TriStar
- Ręczny blender Bogen
- Ręczny blender Exquisit
- Ręczny blender Bartscher
- Ręczny blender Gastroback
- Ręczny blender Continental Edison
- Ręczny blender Bifinett
- Ręczny blender Rolls
- Ręczny blender DCG
- Ręczny blender Soundcraft
- Ręczny blender G3 Ferrari
- Ręczny blender Sanyo
- Ręczny blender Hamilton Beach
- Ręczny blender Gourmetmaxx
- Ręczny blender Clatronic
- Ręczny blender Klark Teknik
- Ręczny blender Inventum
- Ręczny blender SVAN
- Ręczny blender Ariete
- Ręczny blender Graef
- Ręczny blender DBX
- Ręczny blender Princess
- Ręczny blender Innoliving
- Ręczny blender Sunbeam
- Ręczny blender Solac
- Ręczny blender Mackie
- Ręczny blender Waring Commercial
- Ręczny blender Ritter
- Ręczny blender Comfee
- Ręczny blender Breville
- Ręczny blender VOX
- Ręczny blender AYA
- Ręczny blender Chefman
- Ręczny blender Tower
- Ręczny blender Vakoss
- Ręczny blender Solis
- Ręczny blender Kernau
- Ręczny blender Salton
- Ręczny blender Atlas Sound
- Ręczny blender Electroline
- Ręczny blender Lectrosonics
- Ręczny blender Sencor
- Ręczny blender Kalorik
- Ręczny blender TOA
- Ręczny blender Signature
- Ręczny blender Grunkel
- Ręczny blender Vocopro
- Ręczny blender Technical Pro
- Ręczny blender Lagrange
- Ręczny blender Gastronoma
- Ręczny blender Hoberg
- Ręczny blender Dualit
- Ręczny blender Comelec
- Ręczny blender Clas Ohlson
- Ręczny blender Whirlwind
- Ręczny blender OBH Nordica
- Ręczny blender Bestron
- Ręczny blender Swan
- Ręczny blender Dangerous Music
- Ręczny blender Alpina
- Ręczny blender Korona
- Ręczny blender Vice Versa
- Ręczny blender Tomado
- Ręczny blender Juiceman
- Ręczny blender Bellini
- Ręczny blender Oster
- Ręczny blender Sinbo
- Ręczny blender Jata
- Ręczny blender Aigostar
- Ręczny blender Heinner
- Ręczny blender Termozeta
- Ręczny blender Palson
- Ręczny blender Trebs
- Ręczny blender Nordmende
- Ręczny blender Boretti
- Ręczny blender Elba
- Ręczny blender Maxwell
- Ręczny blender SEB
- Ręczny blender Champion
- Ręczny blender Listo
- Ręczny blender Ufesa
- Ręczny blender Brabantia
- Ręczny blender Imetec
- Ręczny blender Bigben
- Ręczny blender Sammic
- Ręczny blender Nova
- Ręczny blender Proctor Silex
- Ręczny blender Saro
- Ręczny blender Hema
- Ręczny blender RGV
- Ręczny blender Pure Acoustics
- Ręczny blender Zephir
- Ręczny blender Efbe-schott
- Ręczny blender Lifetec
- Ręczny blender Wolf
- Ręczny blender Bodum
- Ręczny blender Koenig
- Ręczny blender Turmix
- Ręczny blender Coline
- Ręczny blender Home Electric
- Ręczny blender Dynamic
- Ręczny blender Yorkville
- Ręczny blender Springlane
- Ręczny blender Ideeo
- Ręczny blender Khind
- Ręczny blender Micromaxx
- Ręczny blender Bamix
- Ręczny blender Drawmer
- Ręczny blender Mia
- Ręczny blender Orava
- Ręczny blender Crest Audio
- Ręczny blender Esge
- Ręczny blender MuxLab
- Ręczny blender Ankarsrum
- Ręczny blender Thomas
- Ręczny blender Exido
- Ręczny blender PowerTec Kitchen
- Ręczny blender Nostalgia
- Ręczny blender WestBend
- Ręczny blender Petra Electric
- Ręczny blender Inno-Hit
- Ręczny blender Zedar
- Ręczny blender Girmi
- Ręczny blender RCS
- Ręczny blender Tec Star Home
- Ręczny blender RoyaltyLine
- Ręczny blender Studio
- Ręczny blender WesAudio
- Ręczny blender Tescoma
- Ręczny blender Quest Commercial
- Ręczny blender Cloud
- Ręczny blender Smart Brand
- Ręczny blender Mystery
- Ręczny blender A-Designs
- Ręczny blender Henry Engineering
- Ręczny blender Pyrex
Najnowsze instrukcje dla Ręczny blender
14 Stycznia 2025
14 Stycznia 2025
14 Stycznia 2025
14 Stycznia 2025
14 Stycznia 2025
13 Stycznia 2025
13 Stycznia 2025
13 Stycznia 2025
9 Stycznia 2025
8 Stycznia 2025