Instrukcja obsługi RCF KX 10-A

RCF głośnik KX 10-A

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla RCF KX 10-A (24 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/24
KX 08-A
KX 10-A
ACTIVE HIGH DEFINITION SPEAKERS
OWNER’S MANUAL
MANUALE UTENTE
2
EN
1. SAFETY PRECAUTIONS AND GENERAL INFORMATION
The symbols used in this document give notice of important operating instructions and
warnings which must be strictly followed.
CAUTION
Important operating instructions: explains
hazards that could damage a product,
including data loss
WARNING
Important advice concerning the use of
dangerous voltages and the potential risk of
electric shock, personal injury or death.
IMPORTANT NOTES Helpful and relevant information
about the topic
SUPPORTS, TROLLEYS
AND CARTS
Information about the use of supports,
trolleys and carts. Reminds to move with
extreme caution and never tilt.
WASTE DISPOSAL
This symbol indicates that this product
should not be disposed with your household
waste, according to the WEEE directive
(2012/19/EU) and your national law.
IMPORTANT
This manual contains important information about the correct and safe use of the
device. Before connecting and using this product, please read this instruction
manual carefully and keep it on hand for future reference. The manual is to
be considered an integral part of this product and must accompany it when it
changes ownership as a reference for correct installation and use as well as for the
safety precautions. The company will not assume any responsibility for the incorrect
installation and / or use of this product.
All the precautions, in particular the safety ones, must be read with special
attention, as they provide important information.
SAFETY PRECAUTIONS
GENERAL SAFETY PRECAUTIONS
1. Protect loudspeaker AC and signal lines from damage. Make sure they are
positioned in a way that they cannot be stepped on or crushed by objects.
2. To prevent the risk of electric shock, never open this product: there are no parts
inside that the user needs to access. Never attempt to carry out any operations,
modifications or repairs that are not expressly described in this manual.
3. If this product begins emitting any strange odours or smoke, in case of an active
speaker immediately switch it off and disconnect the power cable; in case of a
passive speaker switch the amplifier off and remove it from the line.
4. Contact your authorized service centre or qualified personnel if any of the
following occur:
- The device does not function (or works in an anomalous way).
- The cable has been damaged.
- Objects or liquids are inside the loudspeaker.
- The loudspeaker has been damaged due to heavy impacts or fire.
5. Make sure that no objects or liquids can get into this product, as this may cause
a short circuit. This apparatus shall not be exposed to dripping or splashing. No
objects filled with liquid, such as vases, shall be placed on this apparatus. No
naked sources (such as lighted candles) should be placed on this apparatus.
6. Do not connect this product to any equipment or accessories not foreseen. For
suspended installation, only use the dedicated anchoring points and do not try
to hang this product by using elements that are unsuitable or not specific for this
purpose. Also check the suitability of the support surface to which the product is
anchored (wall, ceiling, structure, etc.), and the components used for attachment
(screw anchors, screws, brackets not supplied by RCF etc.), which must guarantee
the security of the system / installation over time, also considering, for example,
the mechanical vibrations normally generated by transducers. To prevent the
risk of falling equipment, do not stack multiple units of this product unless this
possibility is specified in the user manual.
7. The company strongly recommends to install this product only by professional
qualified installers (or specialised firms) who can ensure correct installation and
certify it according to the regulations in force. The entire audio system must
comply with the current standards and regulations regarding electrical systems.
8. Supports, trolleys and carts: The equipment should be only used on
supports, trolleys and carts, where necessary, that are recommended
by the manufacturer. The equipment / support / trolley / cart assembly
must be moved with extreme caution. Sudden stops, excessive
pushing force and uneven floors may cause the assembly to overturn. Never tilt
the assembly.
9. Hearing loss: Exposure to high sound levels can cause permanent hearing loss.
The acoustic pressure level that leads to hearing loss is different from person
to person and depends on the duration of exposure. To prevent potentially
dangerous exposure to high levels of acoustic pressure, anyone who is exposed
to these levels should use adequate protection devices. When a transducer
capable of producing high sound levels is being used, it is necessary to wear ear
plugs or protective earphones. See the technical specifications in the instruction
manual for the maximum sound pressure the loudspeaker can produce.
ACTIVE DEVICES: ACTIVE SPEAKERS and AMPLIFIERS
1. The mains voltage is sufficiently high to involve a risk of electrocution; install and
connect this product before plugging it in.
2. Before powering up, make sure that all the connections have been made
correctly and the voltage of your mains corresponds to the voltage shown on the
rating plate on the unit, if not, please contact your dealer.
3. The metallic parts of the unit are earthed through the power cable. An apparatus
with CLASS I construction shall be connected to a mains socket outlet with a
protective earthing connection by a 3-pole power cord.
4. Protect the power cable from damage; make sure it is positioned in a way that it
cannot be stepped on or crushed by objects.
5. If the product is not used for a long period, disconnect the power cable.
6. Ensure that no children have access to the installation materials and components.
7. Before powering up, make sure that all the connections have been made
correctly and the voltage of your mains corresponds to the voltage shown on the
rating plate on the unit. If not, please contact your dealer.
8. Always make sure the power cord and and all plug assemblies are certified
and suitable for the use in the particular countries where the product shall be
installed.
9. Use the mains plug to disconnect the apparatus from the mains.
10. If the device is provided with internal fuse or if it requires operations, contact
your authorized service centre or qualified personnel as defined in the IEC
62368-1 3rd Ed. Interfaces at ES3 level present.
11. If the device is provided with power socket with accessible fuse holder, or
accessible independent fuse holder, disconnect mains cable device before fuse
replacement. The fuse on the AC mains input may be on the neutral, the AC
mains shall be disconnected to de-energize the phase.
PASSIVE DEVICES and ACCESSORIES
1. Loudspeaker lines (amplifier outputs) can have a sufficiently high voltage to
involve a risk of electrocution: never install or connect this loudspeaker when
amplifiers are switched on.
2. Make sure all connections have been made correctly and the loudspeaker input
impedance is suitable for the amplifier output.
3. To ensure a correct sound reproduction, loudspeaker phase is to be respected
(loudspeakers are connected respecting the amplifier polarity). This is important
when loudspeakers are installed adjacent one another, for instance, in the same
room.
4. To prevent inductive effects from causing hum, noise and a bad system working,
loudspeaker lines should not be laid together with other electric cables (mains),
microphone or line level signal cables connected to amplifier inputs.
5. The loudspeaker cable shall have wires (twisted, if possible, to reduce inductive
effects due to surrounding electro-magnetic fields) with a suitable section and
a sufficient electrical insulation. Refer to local regulations since there may be
additional requirements about cable characteristics.
6. Do NOT connect loudspeaker low impedance (8 - 4 Ω) inputs to 100 / 70 V
constant voltage lines.
3
EN
1. SAFETY PRECAUTIONS AND GENERAL INFORMATION
RCF S.p.A. reserves the right to make changes without prior notice to
rectify any errors and / or omissions.
Always refer to the latest version of the manual on www.rcf.it.
SUSPENDED DEVICES
1. Suspending any object is a potentially dangerous operation and should only be
attempted by individuals who have a thorough knowledge of the techniques and
regulations of rigging objects overhead.
2. The company strongly recommends that all devices should be suspended taking
into account all current national, federal, state and local regulations. It is the
responsibility of the installer to ensure that all devices are safely installed in
accordance with all such regulations.
3. The company strongly recommends to inspect the system at least once a year. If
any sign of weakness or damage is detected remedial actions should be taken
immediately.
4. The user is responsible for making sure that the supporting surfaces and any
additional hardware used is capable of supporting the system. Any hardware
used to suspend a loudspeaker array that is not provided by or associated with
the company is not reccomended and is under the responsibility of others.
OPERATING PRECAUTIONS
- Install the product in accordance with manufacturer’s instructions.
- Mechanical and electrical factors need to be considered when installing
a professional audio system (in addition to those which are strictly
acoustic, such as sound pressure, angles of coverage, frequency
response, etc.).
- If the product needs to be used in a cold environment, slowly warm
up the voice coils by sending a low-level signal for about 15 minutes
before sending high-power signals.
- Place this product far from any heat sources and always ensure an
adequate air circulation around it.
- Do not overload this product with too much power or for a long time.
- Never force the control elements (keys, knobs, etc.).
IMPORTANT
To prevent the occurrence of noise on line signal cables, use screened cables only and
avoid putting them close to:
- Equipment that produces high-intensity electromagnetic fields
- Power cables
- Loudspeaker lines
WARNING! CAUTION! To prevent the risk of fire or electric
shock, never expose this product to rain or humidity.
WARNING! To avoid the risk of electric shock, do not connect to
the mains supply if the device is open or, in the case of speakers, while the
grille is removed.
WARNING! To reduce the risk of electric shock, do not disassemble
this product unless you are qualified. Refer servicing to qualified service
personnel.
CORRECT DISPOSAL OF THIS PRODUCT
This product should be handed over to an authorized collection site
for recycling waste electrical and electronic equipment (EEE).
Improper handling of this type of waste could have a possible
negative impact on the environment and human health due to
potentially hazardous substances that are generally associated with EEE.
At the same time, your cooperation in the correct disposal of thisproduct
will contribute to the effective usage of natural resources. For more
information about where you can drop off your waste equipment for
recycling, please contact your local city office, waste authority or your
household waste disposal service.
CARE AND MAINTENANCE
To ensure a long-life service, this product should be used following these advices:
- If the product is intended to be set up outdoors, be sure it is under
cover and protected to rain and moisture.
- In the case of fixed installations, it is recommended to schedule periodic
checks of the entire system and all its parts for the entire duration of
the installation.
- All personnel involved in the installation must be adequately trained
and educated on safety procedures and equipped with appropriate
personal protective equipment (PPE).
- If it is necessary to replace a part, always contact authorized centers
only or use only parts supplied by RCF.
- RCF is not responsible for problems or malfunctions encountered in the
case of replacements of parts or modifications to the system initiated
by the user.
- Do not use abrasives, cleaning solvents, alcohol, benzene or other
volatile substances for cleaning the external parts of this product.
Always use a dry cloth to clean the exterior surfaces of the speaker and
always do it when the power is turned off.
WARNING! CAUTION! For powered devices, clean only
when the power is turned off.

Specyfikacje produktu

Marka: RCF
Kategoria: głośnik
Model: KX 10-A

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z RCF KX 10-A, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje głośnik RCF

RCF

RCF COMPACT C 32 WP Instrukcja

10 Marca 2025
RCF

RCF KX 32-A Instrukcja

11 Lutego 2025
RCF

RCF KXL 4-A Instrukcja

10 Lutego 2025
RCF

RCF KX 515-A Instrukcja

10 Lutego 2025
RCF

RCF KX 10-A Instrukcja

10 Lutego 2025
RCF

RCF HDL 36-AS Instrukcja

12 Stycznia 2025
RCF

RCF NXL 14-A Instrukcja

2 Stycznia 2025
RCF

RCF HD 10-A MK5 Instrukcja

29 Grudnia 2024
RCF

RCF MR 40 Instrukcja

13 Października 2024
RCF

RCF C3108-126 Instrukcja

7 Października 2024

Instrukcje głośnik

Najnowsze instrukcje dla głośnik

Streetz

Streetz CM717 Instrukcja

20 Marca 2025
Streetz

Streetz CM715 Instrukcja

20 Marca 2025
Streetz

Streetz CM716 Instrukcja

20 Marca 2025
SOUNDBOKS

SOUNDBOKS The Battery Instrukcja

20 Marca 2025
ETON

ETON HEX 165 Instrukcja

19 Marca 2025
ETON

ETON PRW 50 Instrukcja

19 Marca 2025
ETON

ETON PFX 10 Instrukcja

19 Marca 2025
ETON

ETON PRA 80 Instrukcja

19 Marca 2025
ETON

ETON PFX 16 Instrukcja

19 Marca 2025
Manta

Manta SPK12GO Instrukcja

19 Marca 2025