Instrukcja obsługi Rane DA216S
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Rane DA216S (6 stron) w kategorii Rozłupnik. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/6
DA216S
DISTRIBUTION AMPLIFIER
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
To reduce the risk of electrical shock, do not open the unit. No user
serviceable parts inside. Refer servicing to qualied service personnel.
e symbols shown below are internationally accepted symbols
that warn of potential hazards with electrical products.
is symbol indicates that a dangerous voltage
constituting a risk of electric shock is present
within this unit.
is symbol indicates that there are important
operating and maintenance instructions in the
literature accompanying this unit.
WARNING
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, registers, stoves, or other apparatus (including ampliers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A
grounding-type plug has two blades and a third grounding prong. e wide blade or third prong is provided for your safety. If the provided plug
does not t into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord and plug from being walked on or pinched particularly at plugs, convenience receptacles, and the point where it exits from
the apparatus.
11. Only use attachments and accessories specied by Rane.
12. Use only with the cart, stand, tripod, bracket, or table specied by the manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply
cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.
15. e plug on the power cord is the AC mains disconnect device and must remain readily operable. To completely disconnect this apparatus from
the AC mains, disconnect the power supply cord plug from the AC receptacle.
16. is apparatus shall be connected to a mains socket outlet with a protective earthing connection.
17. When permanently connected, an all-pole mains switch with a contact separation of at least 3 mm in each pole shall be incorporated in the
electrical installation of the building.
18. If rackmounting, provide adequate ventilation. Equipment may be located above or below this apparatus, but some equipment (like large power
ampliers) may cause an unacceptable amount of hum or may generate too much heat and degrade the performance of this apparatus.
19. is apparatus may be installed in an industry standard equipment rack. Use screws through all mounting holes to provide the best support.
WARNING: To reduce the risk of re or electric shock, do not expose this apparatus to rain or moisture. Apparatus shall not be exposed to dripping
or splashing and no objects lled with liquids, such as vases, shall be placed on the apparatus.
NOTE: is equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
ese limits are designed to provide reasonable protection against harmful interference in a residential installation. is equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Changes or modications not expressly approved by Rane Corporation could void the user's authority to operate the equipment.
is Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
WARNING: is product may contain chemicals known to the State of California to cause cancer, or birth defects or other reproductive harm.
Manual-1
DA216S
DISTRIBUTION AMPLIFIER
OPERATORS MANUAL
Quick Start
is section is for those that just can’t wait to get started. is
Distribution Amplier has a powerful feature not found on most
DA’s – Output assignment switches. If your application calls
for a single channel set-up with one Input driving all Outputs,
set all of the switches to the appropriate Input ( ). To mix A or B
both inputs, set them all to . In this mode, both Inputs drive A+B
all Outputs with the Inputs summed. e MASTER LEVEL
controls set the input level. indicators Occasionally blinking OL
are okay. e individual controls set the level OUTPUT LEVEL
for each Output channel.
For a stereo application, decide how the stereo Outputs are to
be assigned and set the assignment switches accordingly. Eight
stereo outputs are possible.
Set the back panel switches for either LINE or MIC Inputs.
When using microphones that require a “phantom” voltage, turn
WEAR PARTS: is product contains no wear parts.
DA216S
DISTRIBUTION
AMPLIFIER
POWER
MASTER LEVELS
1
OUTPUT LEVELS
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
A
B
on the switch, illuminating its rear panel PHANTOM POWER
LED. Because the phantom voltage is applied to both Inputs,
don’t mix phantom powered and non-phantom powered mics in
the same DA216S. Never engage the phantom voltage when using
an unbalanced mic—doing so may damage the mic. If the mic is
too “hot”, press the switch to reduce the gain INPUT GAIN in
by 20 dB. Incidentally, the INPUT PAD switch reduces the gain
40 dB when in the ). When using the LINE position (pressed in
Inputs for line-level, pressing in both the INPUT PAD and the
INPUT GAIN switches provides a nominal gain of 0 dB. An
additional 16 dB of gain is available when both the MASTER
LEVEL and OUTPUT LEVEL controls are turned all the way
up (clockwise).
e internal universal supply allows operation in almost any
part of the world. All that is required in dierent countries is the
correct IEC line cord.
Specyfikacje produktu
| Marka: | Rane |
| Kategoria: | Rozłupnik |
| Model: | DA216S |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Rane DA216S, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Rozłupnik Rane
22 Września 2024
20 Września 2024
Instrukcje Rozłupnik
- Rozłupnik Samsung
- Rozłupnik Fujitsu
- Rozłupnik StarTech.com
- Rozłupnik Behringer
- Rozłupnik Nedis
- Rozłupnik D-Link
- Rozłupnik ATen
- Rozłupnik APC
- Rozłupnik Hyundai
- Rozłupnik Manhattan
- Rozłupnik Tripp Lite
- Rozłupnik Akasa
- Rozłupnik Icy Box
- Rozłupnik Lindy
- Rozłupnik IFM
- Rozłupnik Digitus
- Rozłupnik Black Box
- Rozłupnik Zipper
- Rozłupnik CLUB3D
- Rozłupnik Rolls
- Rozłupnik Audio-Technica
- Rozłupnik Aluratek
- Rozłupnik Marmitek
- Rozłupnik Atlona
- Rozłupnik Gefen
- Rozłupnik Monacor
- Rozłupnik AMX
- Rozłupnik ACG
- Rozłupnik Audiovox
- Rozłupnik Konig
- Rozłupnik Furuno
- Rozłupnik WyreStorm
- Rozłupnik SIIG
- Rozłupnik Xantech
- Rozłupnik Televés
- Rozłupnik MuxLab
- Rozłupnik Comprehensive
- Rozłupnik Botex
- Rozłupnik Rose Electronics
- Rozłupnik SmartAVI
- Rozłupnik Klover
- Rozłupnik Omnitron Systems
- Rozłupnik Club 3D
Najnowsze instrukcje dla Rozłupnik
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024