Instrukcja obsługi QuickCool QC-PC-C01C

QuickCool Niesklasyfikowane QC-PC-C01C

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla QuickCool QC-PC-C01C (4 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/4
Quick-Ohm Küpper & Co. GmbH
Components – Heat-Management - Ceramics
www.quick-ohm.com vXIII/07/nk
- 1 -
TEC - Controller QC-PC-C01C
Manual
Temperaturecontroller for Cooling
Technial Data:
Dimensions: 65mm x 50mm x 20mm
Temperature range: -20°C…+50°C
Input voltage: 10V…24V
Max. output voltage: equal to input voltage
Max. output current: 10A
1. Basic information QC-PC-C01C
The QC-PC-C01C was designed as controller for cooling to adjust a TEC (Thermoelectric coller)
at a certain temperature. The controller is operated by low DC voltage and should not be exposed
to main voltage. To set up the controller electrical wiring is required, which request some basic
knowledge of electrical circuits. All wiring must be done without connection to the power supply.
Be aware that same components can be damaged or destroyed be incorrect use. Despite of low
voltage, high currents can occur and serious warming and the danger of fire can appear by using
wrong lead wires. Please read this instruction carefully and consult an electrician by any question.
If you remark any warming during operation, the controller must be switched off immediately.
Scope of delivery:
1 TEC - Controller QC-PC-C01C
1 Temperaturesensor NTC 10K ( =3977K) Ω β
1 Potentiometer 10K Ω
1 Manual
Quick-Ohm Küpper & Co. GmbH
Components – Heat-Management - Ceramics
www.quick-ohm.com vXIII/07/nk
- 2 -
2. Operating principle:
A TEC is able to transfer thermal power from one side of the module to the other by consuming
electrical power. The temperature drops on one side of the element, because of heat consumption
while it rises on the other side. For using this heatpump effect in a technical application, a setup
similar to figure 1 is to be built up.
This is the basic setup for any TEC-Application. The area to be temperature controlled must be
equipped with a temperature sensor. On the opposite side, the removed heat must be dissipated to
the ambient. The size of the heatsink and the quality of the thermal contact to the TEC has the
biggest influence on the performance of the whole system. The gap between the TEC and the
mounted parts (hot/cold side) must be as small as possible and only a very little amount auf
thermal conductive should be used to avoid air inclusions in the contact areas. For further
information such as mechanical loads for a durable setup visit our website www.quick-ohm.com.
Heatsink/ hot
side
Thermal
conductive
(Paste, Foil,
etc.)
TEC
(printing on
upper side)
Temp. controlled
area/ cold side
figure 1:
Temperatur
e
sensor
Quick-Ohm Küpper & Co. GmbH
Components – Heat-Management - Ceramics
www.quick-ohm.com vXIII/07/nk
- 3 -
3. Electrical connection:
For operating the controller a DC power supply is needed. Please be aware that the controller has
no internal voltage or current limits and therefore will output the maximum voltage of the power
supply when the set-temperature is much lower than the actual temperature. Make sure, that the
maximum voltage of the power supply is within the range of the TEC. A series connection of
similar TECs can also be used to reduce the voltage for each TEC. Figure 2 shows the electrical
connection of the whole circuit, the colors follow the lead colors of the controller.
By following these instructions and using TECs from QUICK-OHM, the top side of the TEC will
get cold when the right wire showing in the direction of the viewer is red. Applied on the figure
above, the top side would be the warm side.
4. Temperature setting:
The controller has a working range from -20°C to + 50°C. Please notice, that the controller can
only be operated in cooling mode. 50°C can only be reached, when the hot side is above this
temperature. It could be useful to make marks on the potentiometer while the first use. By
adjusting some positions between the left and right stop of the potentiometer and while measuring
the temperature at that steps a small scale can be marked on the potentiometer.
It is possible to integrate a Display (QC-PC-D-100) in the setup. This device shows the set-
temperature as well as the actual temperature.
Controller
QC-PC-C01C
+ -
Power supply
10V … 24V
TEC
Temperatur-
Sensor
NTC 10K Ω
Potentiometer 10K
Ω
figure 2:
White
+5V Poti
Yellow
Control
Poti-Signal
Green
Gnd
Sens/Poti
Grey
Sensor
Signal
Red
+PE
Blue
-PE
Black
GND
Orange
10..24V

Specyfikacje produktu

Marka: QuickCool
Kategoria: Niesklasyfikowane
Model: QC-PC-C01C

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z QuickCool QC-PC-C01C, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane QuickCool

QuickCool

QuickCool QC-PC-C01C Instrukcja

2 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024