Instrukcja obsługi QSC CX302V

QSC odbiornik CX302V

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla QSC CX302V (3 stron) w kategorii odbiornik. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/3
Current draw—120 VAC Page 1 of 3
February 2016
Idle
Current
draw at
idle or
with very
low signal
level.
8Ω 4Ω 2Ω 8Ω 4Ω 2Ω 8Ω 4Ω 2Ω25V-70V-100V 25V-70V-100V 25V-70V-100V
Model Amperes Amperes Amperes Amperes Amperes Amperes Amperes Amperes Amperes Amperes Amperes Amperes Amperes
CX302 0.9 3.5 5.4 8.6 na 5.1 8.7 12.9 na 8.4 13.9 22.2 na
CX502 0.9 5.1 8.0 11.9 na 7.6 12.1 18.2 na 12.6 21.2 32.2 na
CX702 0.8 5.0 7.7 11.5 na 8.3 13.2 19.8 na 15.9 26.7 41.1 na
CX902 0.9 5.9 9.2 13.2 na 10.5 16.8 24.6 na 20.4 34.3 52.3 na
CX1102 0.9 7.6 11.6 16.6 na 13.1 20.3 30.4 na 25.1 40.6 58.6 na
CX302V 1.0 nr nr nr 5.6 nr nr nr 8.0 nr nr nr 12.0
CX602V 0.9 8.7 nr nr 8.7 13.0 nr nr 13.0 20.5 nr nr 20.5
CX1202V 1.0 7.7 11.9 nr 11.9 12.5 19.2 nr 19.2 25.2 38.7 nr 38.7
CX254 0.7 5.8 9.2 14.3 na 8.8 14.2 21.7 na 14.8 24.0 38.2 na
CX404 0.7 8.1 12.4 nr na 12.2 19.3 nr na 21.7 33.4 nr na
CX204V 0.8 nr nr nr 8.3 nr nr nr 12.7 nr nr nr 20.1
CX168 0.6 6.4 10.0 nr na 9.9 15.1 nr na 16.5 26.0 nr na
CX108V 0.6 nr nr nr 6.4 nr nr nr 10.2 nr nr nr 15.6
CX Series Amplifier Current Draw—120 VAC
Current draw at 1/8 of full power is measured
with pink noise as a signal. It approximates
operating with music or voice with light clipping
and repesents the amplifier's typical "clean"
maximum level, without audible clipping. Use
these figures for typical maximum level
operation.
Current draw at 1/3 of full power is measured
with pink noise as a signal. It approximates
operating with music or voice with very heavy
clipping and a very compressed dynamic range.
Current draw at full power is measured with a 1
kHz sine wave. However, it does not represent
any real-world operating condition.
"Current draw" is the amount of AC current an amplifier demands while it is operating.
Measurements are provided for various loads at idle, 1/8 of average full power, 1/3 of average full
power, and full power, with all channels driven simultaneously. The figures shown on this sheet are
for 120 VAC usage; for 230- and 100-volt operation, see the companion sheets. For typical usage,
use the idle and 1/8 power figures.
"nr" respectively mean "not applicable" to the particular amplifier model and "not rated" for the
particular load impedance. Bridged mono into 8 ohms is equivalent to 4 ohms per channel; into 4
ohms is equivalent to 2 ohms per channel.
1/8 Power
1/3 Power
Full Power
Load per channel ->
Current draw—230 VAC Page 2 of 3
February 2016
Idle
Current
draw at
idle or
with very
low signal
level.
8Ω 4Ω 2Ω 8Ω 4Ω 2Ω 8Ω 4Ω 2Ω25V-70V-100V 25V-70V-100V 25V-70V-100V
Model Amperes Amperes Amperes Amperes Amperes Amperes Amperes Amperes Amperes Amperes Amperes Amperes Amperes
CX302 0.5 1.8 2.7 4.3 na 2.6 4.4 6.5 na 4.2 7.0 11.1 na
CX502 0.5 2.6 4.0 6.0 na 3.8 6.1 9.1 na 6.3 10.6 16.1 na
CX702 0.4 2.5 3.9 5.8 na 4.2 6.6 9.9 na 8.0 13.4 20.6 na
CX902 0.5 3.0 4.6 6.6 na 5.3 8.4 12.3 na 10.2 17.2 26.2 na
CX1102 0.5 3.8 5.8 8.3 na 6.6 10.2 15.2 na 12.6 20.3 29.3 na
CX302V 0.5 nr nr nr 2.8 nr nr nr 4.0 nr nr nr 6.0
CX602V 0.5 4.4 nr nr 4.4 6.5 nr nr 6.5 10.3 nr nr 10.3
CX1202V 0.5 3.9 6.0 nr 6.0 6.3 9.6 nr 9.6 12.6 19.4 nr 19.4
CX254 0.4 2.9 4.6 7.2 na 4.4 7.1 10.9 na 7.4 12.0 19.1 na
CX404 0.4 4.1 6.2 nr na 6.1 9.7 nr na 10.9 16.7 nr na
CX204V 0.4 nr nr nr 4.2 nr nr nr 6.4 nr nr nr 10.1
CX168 0.3 3.2 5.0 nr na 5.0 7.6 nr na 8.3 13.0 nr na
CX108V 0.3 nr nr nr 3.2 nr nr nr 5.1 nr nr nr 7.8
Load per channel ->
"Current draw" is the amount of AC current an amplifier demands while it is operating.
Measurements are provided for various loads at idle, 1/8 of average full power, 1/3 of average full
power, and full power, with all channels driven simultaneously. The figures shown on this sheet are
for 230 VAC usage; for 120- and 100-volt operation, see the companion sheets. For typical usage,
use the idle and 1/8 power figures.
"nr" respectively mean "not applicable" to the particular amplifier model and "not rated" for the
particular load impedance. Bridged mono into 8 ohms is equivalent to 4 ohms per channel; into 4
ohms is equivalent to 2 ohms per channel.
CX Series Amplifier Current Draw—230 VAC
Current draw at 1/8 of full power is measured
with pink noise as a signal. It approximates
operating with music or voice with light clipping
and repesents the amplifier's typical "clean"
maximum level, without audible clipping. Use
these figures for typical maximum level
operation.
Current draw at 1/3 of full power is measured
with pink noise as a signal. It approximates
operating with music or voice with very heavy
clipping and a very compressed dynamic range.
Current draw at full power is measured with a 1
kHz sine wave. However, it does not represent
any real-world operating condition.
1/8 Power
1/3 Power
Full Power
Current draw—100 VAC Page 3 of 3
February 2016
Idle
Current
draw at
idle or
with very
low signal
level.
8Ω 4Ω 2Ω 8Ω 4Ω 2Ω 8Ω 4Ω 2Ω25V-70V-100V 25V-70V-100V 25V-70V-100V
Model Amperes Amperes Amperes Amperes Amperes Amperes Amperes Amperes Amperes Amperes Amperes Amperes Amperes
CX302 1.1 4.2 6.5 10.3 na 6.1 10.4 15.5 na 10.1 16.7 26.6 na
CX502 1.1 6.1 9.6 14.3 na 9.1 14.5 21.8 na 15.1 25.4 38.6 na
CX702 1.0 6.0 9.2 13.8 na 10.0 15.8 23.8 na 19.1 32.0 49.3 na
CX902 1.1 7.1 11.0 15.8 na 12.6 20.2 29.5 na 24.5 41.2 62.8 na
CX1102 1.1 9.1 13.9 19.9 na 15.7 24.4 36.5 na 30.1 48.7 70.3 na
CX302V 1.2 nr nr nr 6.7 nr nr nr 9.6 nr nr nr 14.4
CX602V 1.1 10.4 nr nr 10.4 15.6 nr nr 15.6 24.6 nr nr 24.6
CX1202V 1.2 9.2 14.3 nr 14.3 15.0 23.0 nr 23.0 30.2 46.4 nr 46.4
CX254 0.8 7.0 11.0 17.2 na 10.6 17.0 26.0 na 17.8 28.8 45.8 na
CX404 0.8 9.7 14.9 nr na 14.6 23.2 nr na 26.0 40.1 nr na
CX204V 1.0 nr nr nr 10.0 nr nr nr 15.2 nr nr nr 24.1
CX168 0.7 7.7 12.0 nr na 11.9 18.1 nr na 19.8 31.2 nr na
CX108V 0.7 nr nr nr 7.7 nr nr nr 12.2 nr nr nr 18.7
Load per channel ->
"Current draw" is the amount of AC current an amplifier demands while it is operating.
Measurements are provided for various loads at idle, 1/8 of average full power, 1/3 of average full
power, and full power, with all channels driven simultaneously. The figures shown on this sheet are
for 100 VAC usage; for 230- and 120-volt operation, see the companion sheets. For typical usage,
use the idle and 1/8 power figures.
"nr" respectively mean "not applicable" to the particular amplifier model and "not rated" for the
particular load impedance. Bridged mono into 8 ohms is equivalent to 4 ohms per channel; into 4
ohms is equivalent to 2 ohms per channel.
CX Series Amplifier Current Draw—100 VAC
Current draw at 1/8 of full power is measured
with pink noise as a signal. It approximates
operating with music or voice with light clipping
and repesents the amplifier's typical "clean"
maximum level, without audible clipping. Use
these figures for typical maximum level
operation.
Current draw at 1/3 of full power is measured
with pink noise as a signal. It approximates
operating with music or voice with very heavy
clipping and a very compressed dynamic range.
Current draw at full power is measured with a 1
kHz sine wave. However, it does not represent
any real-world operating condition.
1/8 Power
1/3 Power
Full Power

Specyfikacje produktu

Marka: QSC
Kategoria: odbiornik
Model: CX302V

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z QSC CX302V, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje odbiornik QSC

QSC

QSC CX4 Instrukcja

7 Stycznia 2025
QSC

QSC DPA4.2Q Instrukcja

7 Stycznia 2025
QSC

QSC USA 400 Instrukcja

7 Stycznia 2025
QSC

QSC DPA4.3Q Instrukcja

7 Stycznia 2025
QSC

QSC USA 900 Instrukcja

7 Stycznia 2025
QSC

QSC SRA1222 Instrukcja

7 Stycznia 2025
QSC

QSC 1400 Instrukcja

7 Stycznia 2025
QSC

QSC 1200 Instrukcja

7 Stycznia 2025
QSC

QSC CX12 Instrukcja

7 Stycznia 2025
QSC

QSC CX6 Instrukcja

7 Stycznia 2025

Instrukcje odbiornik

Najnowsze instrukcje dla odbiornik

Marantz

Marantz SR-8000 Instrukcja

15 Stycznia 2025
AKAI

AKAI AM-32 Instrukcja

15 Stycznia 2025
Peavey

Peavey CKd 608 Instrukcja

15 Stycznia 2025
OSD Audio

OSD Audio Nero HTX4150 Instrukcja

14 Stycznia 2025
S.M.S.L

S.M.S.L PA200 Instrukcja

14 Stycznia 2025
Pyle

Pyle PFMRA340BB.5 Instrukcja

13 Stycznia 2025
Wavtech

Wavtech link700.4plus Instrukcja

13 Stycznia 2025
Behringer

Behringer NU6000DSP Instrukcja

12 Stycznia 2025
Denon

Denon DRA-935R Instrukcja

12 Stycznia 2025
Kenwood

Kenwood KMM-BT508DAB Instrukcja

12 Stycznia 2025