Instrukcja obsługi Pyle PLCMDVR15

Pyle Kamera monitorująca PLCMDVR15

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Pyle PLCMDVR15 (18 stron) w kategorii Kamera monitorująca. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/18

PyleAudio.com

Table of Contents

1. Notes ........................................................................................................................ 2

2. Production Specification .......................................................................................... 2

3. Instructions for I/O Alarm Input and Output ............................................................. 3

4. Instructions for Remote Control ............................................................................... 4

4.1 Description of Remote Control Buttons .............................................................. 4

4.2 Soft Keyboard Input Description ......................................................................... 4

5. VCR Instructions ...................................................................................................... 5

5.1 User Login .......................................................................................................... 5

5.2 Preview Interface ................................................................................................ 6

5.3 Video Retrieval ................................................................................................... 7

5.3.1 Instructions for Detailed Files and Backup................................................... 7

5.4 Video Setting ...................................................................................................... 8

5.4.1 Frame Rate Dynamic Configuration ............................................................ 8

5.4.2 Small Bit Stream Configuration .................................................................... 9

5.5 Features Setting ................................................................................................. 9

5.5.1 Time Setting ............................................................................................... 10

5.5.2 Storage Device Management .................................................................... 11

5.5.3 Instructions for Equipment Maintenance and System Upgrade ................. 11

5.5.4 System Setting ........................................................................................... 11

5.6 System Information .......................................................................................... 12

5.7 Vehicle Information ........................................................................................... 12

5.7.1 Startup/Shutdown Setting .......................................................................... 13

5.8 Display Setting ................................................................................................. 14

5.9 Password Management .................................................................................... 14

6.3 G Networking and Platform Application ............................................................... 15

PyleAudio.com

1. Notes

1.1 Definitions of connectors for aviation interfaces:

1 red: +12V positive pole

2 black: common GND

3 white: audio

4 yellow: video

1.2 Definitions of power cords:

Red: DC12V or 24V input

Black: ground GND

Yellow: ignition wire GND

1.3 Do the following to properly start the machine:

1. Lock the key lock (the lock is the switch of the machine);

2. Connect the red power cord to the battery positive, the black cord to the negative, the

yellow cord to the ignition wire of the car key (or ACC); or else, combine the red and yellow

cords as positive pole and black as negative.

Note:

1) Make sure the voltage of the battery is between 8V-36V before connection; otherwise,

the equipment may be burnt out;

2) With the cords connected, pay attention to the insulation between the cords to prevent

burning out of the battery due to short circuit of the cords;

3) Make the yellow cord is connected to the ignition wire; otherwise, the equipment will not

support delayed shutdown and the last video will be lost.

4) Note: the installation of on-board machine must use the positive and negative of the

battery instead of using bond strap as ground wire because bond strap will produce

negative impulse to disturb the normal operation of the host. The power cords for the

positive and negative power cord must be over 1.0mm in diameter. Φ

2. Production Specification

MDVR is a cost-effective and functionally expandable equipment designed for video

surveillance and remote monitoring in cars, trains and other vehicles. It uses a high-speed

processor and an embedded Linux platform, in combination with the state-of-the-art H.264

video compression/decompression technology in the IT field. With SD card/hard disk as a

storage medium, MDVR is capable of 4-channel audio and video recording and driving

information recording in formats of CIF, HD1 and D1. MDVR is characterized by simple

appearance, superior vibration-proof performance, flexible and easy installation, powerful

functions and high reliability.

Specyfikacje produktu

Marka:	Pyle
Kategoria:	Kamera monitorująca
Model:	PLCMDVR15

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Pyle PLCMDVR15, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Kamera monitorująca Pyle

Pyle PIPCAMHD22WT Instrukcja

31 Sierpnia 2024

Pyle PIPCAM15 Instrukcja

24 Sierpnia 2024

Pyle PIPCAMHD82 Instrukcja

24 Sierpnia 2024

Pyle PLCMDVR15 Instrukcja

20 Sierpnia 2024

Pyle PPBCM10 Instrukcja

19 Sierpnia 2024

Pyle PIPCAM8 Instrukcja

19 Sierpnia 2024

Instrukcje Kamera monitorująca

Najnowsze instrukcje dla Kamera monitorująca

Dahua Technology Pro IPC-HDPW5442G-Z Instrukcja

15 Stycznia 2025

Toshiba IKS-WR7412 Instrukcja

13 Stycznia 2025

AVerMedia FC1320-P Instrukcja

13 Stycznia 2025

Digitus OptiMax DN-16037 Instrukcja

13 Stycznia 2025

Hikvision DS-2CE59U1T-AVPIT3ZF Instrukcja

12 Stycznia 2025

Hikvision IDS-2CD7526G0-IZHSY Instrukcja

12 Stycznia 2025

Hikvision DS-2CD2163G0-I(S) Instrukcja

12 Stycznia 2025

Hikvision DS-2CD2H83G1-IZS Instrukcja

12 Stycznia 2025

Speco Technologies O5LB1 Instrukcja

12 Stycznia 2025

ZKTeco AntarVis 2.0 Instrukcja

12 Stycznia 2025