Instrukcja obsługi Psiber CM450 CableMaster
Psiber
Meetinstrumenten
CM450 CableMaster
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Psiber CM450 CableMaster (8 stron) w kategorii Meetinstrumenten. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/8
CableMaster
CM450
Quick Start Guide
Testing:
A. Plug the wire into the correct Test Port, Ethernet to RJ45
B. Plug the opposite end into the Main Remote
C. Press Network Button
D. The LCD Display reports wire condition, Pass/Fail
E. To turn off, press O/ID Button
Toning:
A. With the unit turned OFF, hold down the LENGTH/TONE button until
LCD illuminates
B. To select a tone cadence, press the LENGTH/TONE button repeatedly to step
through the four cadence options: HI, LO, Hi-Lo1, and Hi-Lo1. Stop when you
reach the option you want. The option you select determines the cadence sent
from the main tester, through the cable, and picked up by the tone tracer probe.
C. Press the appropriate cable type button (voice, video, or data) to select a
cable for the tone signal
* Note: Tone is detected by a tone tracer probe
Length Measurement:
A. Make sure the CM450 is turned OFF.
B. Insert the cable plug into the corresponding receiver on the main tester (RJ-11
jack for voice cable, RJ-45 jack for data cables, F-Connector for video cables).
C. Press the LENGTH/TONE button to enter Length Mode.
D. Press the cable type button corresponding to the connector in use.
Features:
Testing: CM450 shows Opens, Shorts, Miswires, Split Pairs, PASS and
FAIL results quickly.
Toning: CM450’s built-in tone generator is a fl exible and function-packed
tone generator. Its confi gurable signal can be generated to fi nd and fi x the
position on any type of cable - either exposed or hidden, in ceilings or
behind walls.
Length: CM450 determines the length (in feet or meters) of an entire cable and/
or individual wire pairs within the cable.
Option: CM450 is supported by (1-19) wiremapping ID locators (Network/Coax)
and (1-8) testing/ID remotes (Network/Telephone).
Button Function
1. LCD Display
2. Voice Mode
3. Video Mode
4. Data Mode
1
4
3
6
7
5
2
5. Length/Tone Mode
6. On/Off and ID Mode
7. Main Unit Remote
(RJ11, RJ45)
CableMaster
CM450
Quick Start Guide
Kurzanleitung
Guide de Démarrage Rapide
CableMaster
CM450
Quick Start Guide
Testing:
A. Plug the wire into the correct Test Port, Ethernet to RJ45
B. Plug the opposite end into the Main Remote
C. Press Network Button
D. The LCD Display reports wire condition, Pass/Fail
E. To turn off, press O/ID Button
Toning:
A. With the unit turned OFF, hold down the LENGTH/TONE button until
LCD illuminates
B. To select a tone cadence, press the LENGTH/TONE button repeatedly to step
through the four cadence options: HI, LO, Hi-Lo1, and Hi-Lo1. Stop when you
reach the option you want. The option you select determines the cadence sent
from the main tester, through the cable, and picked up by the tone tracer probe.
C. Press the appropriate cable type button (voice, video, or data) to select a
cable for the tone signal
* Note: Tone is detected by a tone tracer probe
Length Measurement:
A. Make sure the CM450 is turned OFF.
B. Insert the cable plug into the corresponding receiver on the main tester (RJ-11
jack for voice cable, RJ-45 jack for data cables, F-Connector for video cables).
C. Press the LENGTH/TONE button to enter Length Mode.
D. Press the cable type button corresponding to the connector in use.
Features:
Testing: CM450 shows Opens, Shorts, Miswires, Split Pairs, PASS and
FAIL results quickly.
Toning: CM450’s built-in tone generator is a fl exible and function-packed
tone generator. Its confi gurable signal can be generated to fi nd and fi x the
position on any type of cable - either exposed or hidden, in ceilings or
behind walls.
Length: CM450 determines the length (in feet or meters) of an entire cable and/
or individual wire pairs within the cable.
Option: CM450 is supported by (1-19) wiremapping ID locators (Network/Coax)
and (1-8) testing/ID remotes (Network/Telephone).
Button Function
1. LCD Display
2. Voice Mode
3. Video Mode
4. Data Mode
1
4
3
6
7
5
2
5. Length/Tone Mode
6. On/Off and ID Mode
7. Main Unit Remote
(RJ11, RJ45)
CableMaster
CM450
Quick Start Guide
Button Function
1 LCD Display 5 Length/Tone Mode
2 Voice Mode 6 On/Off and ID Mode
3 Video Mode 7 Main Unit Remote
4 Data Mode (RJ11/RJ12, RJ45)
English
A. Plug the wire into the correct Test Port, e.g. Ethernet to RJ45
B. Plug the opposite end into the Main Remote
C. Press Network Button
D. The LCD Display reports wire condition, Pass/Fail
E. To turn off, press O/ID Button
Toning:
A. With the unit turned OFF, hold down the LENGTH/TONE button until
LCD illuminates
B. To select a tone cadence, press the LENGTH/TONE button repeatedly to
step through the four cadence options: HI, LO, Hi-Lo1, and Hi-Lo 2. Stop
when you reach the option you want. The option you select determines the
cadence sent from the main tester, through the cable, and picked up by the
tone tracer probe*.
C. Press the appropriate cable type button (voice, video or data) to select a
cable for the tone signal
* Note: Tone is detected by a tone tracer probe (optional)
Length Measurement:
A. Make sure the CM450 is turned OFF.
B. Insert the cable plug into the corresponding receiver on the main tester
(RJ-11/RJ12) jack for voice cable, RJ-45 jack for data cables, F-Connector
for video cables).
C. Press the LENGTH/TONE button to enter Length Mode.
D. Press the cable type button corresponding to the connector in use
Features:
Testing: CM450 shows Opens, Shorts, Miswires, Split Pairs, PASS and
FAIL results quickly.
Toning: CM450`s built- in tone generator is a flexible and function- packed
Tone generator. Its configurable signal can be generated to find and fix the
position on any type of cable – either exposed or hidden, in ceilings or
behind walls.
Length: CM450 determines the length (in feet or meters) of an entire cable and/
or individual wire pairs within the cable.
Option: CM450 is supported by (1-19) wiremapping ID locators (Network/Coax)
and (1-8) testing/ID remotes (Network/Telephone).
English
Specyfikacje produktu
Marka: | Psiber |
Kategoria: | Meetinstrumenten |
Model: | CM450 CableMaster |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Psiber CM450 CableMaster, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Meetinstrumenten Psiber
27 Września 2024
Instrukcje Meetinstrumenten
- Meetinstrumenten Bosch
- Meetinstrumenten Stanley
- Meetinstrumenten Sonel
- Meetinstrumenten Perel
- Meetinstrumenten Gossen Metrawatt
- Meetinstrumenten Fluke
- Meetinstrumenten Megger
- Meetinstrumenten BENNING
- Meetinstrumenten Ferrex
- Meetinstrumenten Brandson
- Meetinstrumenten Vonroc
- Meetinstrumenten Powerfix
- Meetinstrumenten Workzone
- Meetinstrumenten Beha-Amprobe
- Meetinstrumenten Laserliner
- Meetinstrumenten Profitec
- Meetinstrumenten AS - Schwabe
- Meetinstrumenten Defort
- Meetinstrumenten Max
- Meetinstrumenten Metrel
- Meetinstrumenten Nieaf-Smitt
- Meetinstrumenten Uni-Trend
Najnowsze instrukcje dla Meetinstrumenten
27 Września 2024
27 Września 2024
27 Września 2024
26 Września 2024
26 Września 2024
26 Września 2024
26 Września 2024
25 Września 2024
24 Września 2024
24 Września 2024