Instrukcja obsługi Projecta HDBT122


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Projecta HDBT122 (8 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 12 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/8
Tray Fitting Instructions to suit Auxiliary battery for
TOYOTA LANDCRUISER 70 SERIES
Years: October 2016 Onwards
Models: 1VD-FTV 4.5 Litre V8 Turbo Diesel Wagon / Ute
HEAVY DUTY DUAL BATTERY TRAY
P/No. HDBT122
2
IMPORTANT SAFETY INFORMATION
Please read this instruction thoroughly before fitting the tray.
This product is recommend to be fitted by a workshop or qualified mechanical person.
WARNINGS
Before installation, make sure that the vehicle is stationary and the wheels chocked.
Be careful when laying wires, not to cause any electrical shorts or wire breakage.
After installation ensure the bonnet can close without hitting the newly installed battery
and battery tray.
Ensure original parts and pipes have sufficient clearance from the tray and battery.
Push them away from the tray if required.
SPECIFICATIONS
Max Battery Size (mm) L300x W174 x H220
Max Battery Weight 28Kg
Recommended batteries Optima D27M & Optima D31A
Approximate fitting time 1.5 hours
Recommended Dual P/No: IDC25, DBC150, VSR200
Battery System
Tray Location Engine Bay, Passenger Side Rear
KIT INCLUDES
Hardware
2 x M8 Bolts
2 x M8 Bolts Long
1 x M8 Nut
3 x M6 Bolts
1 x M6 Weld Nut
4 x M6 Nuts
3 x M6 Body Washer
Long Top
Mount
Short Top
Mount
Computer
Mount
J Bolts
Top
Mount
Tray
3
FITTING INSTRUCTIONS
1. Make sure that the vehicle is stationary, the engine is switched off and cool.
Disconnect the negative terminal from the main battery.
2. Remover brackets on the inner guard holding 2 x “Injector Driver” Computers.
Disconnect plugs one computer has 3 plugs and the other has 4 plugs.
3. Remove computers from brackets (brackets not re-used, but retain screws)
4a. Grab the Supplied Computer mount and see how it is going to be mounted using
the 10mm hole at the top.
4b. Locate the back of the bracket and mount the 3 plug computer on the back to the
lower series of holes.
4c. Mount the 4 plug computer on the front of the bracket on the top series of holes
with the plugs facing down
5. Remove factory accessory fuse box from its bracket from the inner guard. The fuse
box may be redundant when the dual battery system is completed. For the time
being cable tie to the wiring harness between battery and intercooler.
6a. Undo 3 nuts holding wiring harness mount bracket to 2 studs on firewall (below
wiper motor) and unclip harness from bracket.


Specyfikacje produktu

Marka: Projecta
Kategoria: Niesklasyfikowane
Model: HDBT122

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Projecta HDBT122, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Niesklasyfikowane Projecta

Projecta

Projecta SC015 Instrukcja

2 Października 2024
Projecta

Projecta HDBT200 Instrukcja

11 Września 2024
Projecta

Projecta SC320D Instrukcja

7 Września 2024
Projecta

Projecta VR020 Instrukcja

6 Września 2024
Projecta

Projecta SC220 Instrukcja

5 Września 2024
Projecta

Projecta VR005 Instrukcja

2 Września 2024
Projecta

Projecta LVD30 Instrukcja

2 Września 2024
Projecta

Projecta HDBT252 Instrukcja

2 Września 2024
Projecta

Projecta DBC150 Instrukcja

30 Sierpnia 2024
Projecta

Projecta HDBT108 Instrukcja

30 Sierpnia 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane