Instrukcja obsługi Pro-Lift W-1808

Pro-Lift kompresor W-1808

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Pro-Lift W-1808 (4 stron) w kategorii kompresor. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/4
1
Air Inator
Operating Instructions and Parts Manual
SFA Companies, Inc.
10939 N. Pomona Ave.
Kansas City, MO 64153
Tel (816) 891-6390, Fax (816) 891-6599 Printed in China
W-1808-M0_072015
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey
all safety messages that follow this symbol to avoid possible injury or property damage
!
Model W-1808
2
SAFETY AND GENERAL INFORMATION
Save these instructions for future use. Study, understand
and follow all instructions before operating this device. The
owner and operator of this device shall have an under-
standing of the product and safe operating procedures
before attempting to use. If any doubt exists as to the safe
and proper use of this product, remove from service imme-
diately. Instructions and safety materials shall be conveyed
in the operator’s native language before use of this product
is authorized.
• Study, understand and follow all instructions before operating this device.
• When using this air inator, basic safety precautions should always be followed to reduce risk of re or electrical shock.
• Do not exceed rated pressure of the item being inated.
• Do not leave device operating and unattended.
• If DC plug fuse is blown, only replace with fuse of identical rating.
• This device contains a DC motor and components which may arc during normal operation. This arcing may ignite
ammable gases. Do not operate in a ammable environment.
• Keep out of reach of children.
• The power cord on this product contains chemicals known to the State of California to cause cancer and birth defects
or other reproductive harm. Wash hands after handling (California law requires this warning to be given to customers
in the State of California).
• Do not alter this product.
• Failure to heed these markings may result in personal injury and/or property damage.
! WARNING
Inspect before each use. Do not use if bent, broken,
melted, burned or otherwise damaged components are
noted. A inator that is damaged in any way or operates
abnormally shall be removed from service immediately.
This unit is designed for intermittent use only. Operation
beyond it’s designed duty cycle may result in inator and/
or vehicle damage. NEVER exceed rated pressure of the
item being inated. If rated pressure is exceeded, the item
being inated may burst.
PRODUCT DESCRIPTION
The Pro-Lift Air Inator is designed to inate automotive
and light truck tires to manufacturer’s recommended pres-
sure. It can also be used to inate inatables such as rafts,
cushions and sports balls. It has a built-in LED work light
and digital pressure readout with auto shut-off function.
Refer to the vehicle’s owners manual or inatable product
owner’s manual before using the inator.
OPERATION
Work Light
Fused 12V DC Plug
Air Hose with
Screw Connect
Digital
Pressure
Readout
Inator/Light
Switch
Figures 1 & 2 - W-1808 Nomenclature
3
A. High Pressure Inatables (Tires)
1. Remove air hose and screw inator nozzle onto tire
stem.
2. Remove Power Cord from storage compartment and
insert into a suitable outlet or 12V DC source.
3. Set desired pressure by using the “+” and “-” buttons (g.
1)
NOTICE: The “R” button will change the units of the pres-
sure readout.
4. Toggle inator switch to position. Unit will begin inatI -
ing to predetermined pressure setting (determined from
vehicle or tire manufacturer’s specication).
5. Inator will shut off when the pressure has reached pres-
sure setting. Toggle inator switch to OFF (centered)
and unplug the inator power cord.
6. Use a tire gauge to check ination and adjust to desired
pressure as recommended by the vehicle and/or tire
manufacturer.
NOTICE: Always double check air pressure using a reli-
able pressure gauge.
B. Low Pressure Inatables
1. To inate air mattresses, beach balls, life jackets, etc.,
select the suitable adapter (Fig. 3), then insert and se-
cure into the end of the air hose (Fig. 2).
2. Insert the connector adapter into the appropriate receiver
on the inatable.
3. Plug the inator into a DC 12V outlet. Toggle inator
switch to I position. Unit should commence ination.
4. Inate to a pressure or level of rmness recommended
by the manufacturer. Toggle inator switch to OFF (cen-
ter) then unplug the power cord from the DC 12V outlet.
C. Operating the Work Light
1. Plug the Inator into a suitable 12V DC power source.
2. Toggle Inator/Light switch to II position for steady, high-
intensity, work light. Centered switch position extinguish-
es light.
E. REPLACING THE FUSE
(15A 6mm dia. x 30mm glass tube current fuse)
1. Unscrew the plastic 12V DC plug cap.
2. Gently remove 15A fuse and replace with fuse of same
rating and size.
3. Place fuse properly in position to allow installation of
plastic cap.
4. Reinstall plastic 12V DC plug cap.
TIPS FOR OPERATION
1. Ensure vehicle battery is sufciently charged to operate
inator.
2. If Inator does not operate when plugged into a DC 12V
outlet, check connections at back of DC 12V plug as well
the fuse receptacle. Replace as needed with a fuse of
identical rating. Never replace with fuse of higher rating.
No user replaceable parts exist for this item, refer any
repairs to qualied personnel only.
3. Do not overheat the Inator, monitor cycle times (Inator
on and off periods). Never exceed 15 minutes continu-
ous running. Let unit cool for 15 minutes, then reattempt
use.
4. Operate and store in a clean, dry environment. Do not
obstruct the unit’s cooling vents.
Performance Tip: Keep your tires inated per the vehicle’s
owner’s manual. This will increase gas mileage and re-
duce tire wear.
SPECIFICATIONS
Model: W-1808
Power Requirement: 12V DC
Duty Cycle: 15 min. on/15 min. off
Power: 120W @ 12V DC
Fuse: 15A (6mm x 30mm)
Maximum Air Flow: 1.06 CFM (high pressure)
Air Hose Length: 30”
Power Cord Length: 9.8 ft.
Figure 3
Sports Adapter
Large Diameter
Air Hose
Adapters for Inatables

Specyfikacje produktu

Marka: Pro-Lift
Kategoria: kompresor
Model: W-1808

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Pro-Lift W-1808, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje kompresor Pro-Lift

Pro-Lift

Pro-Lift W-1806 Instrukcja

16 Września 2024
Pro-Lift

Pro-Lift W-1808 Instrukcja

16 Września 2024

Instrukcje kompresor

Najnowsze instrukcje dla kompresor

MSW

MSW -SPS-24 Instrukcja

15 Października 2024
MSW

MSW -UVRSRI Instrukcja

15 Października 2024
Ferm

Ferm CRM1027 FCO-1524 Instrukcja

13 Października 2024
Einhell

Einhell BT-AC 180/6 Kit Instrukcja

9 Października 2024
Einhell

Einhell N-KS 210/8/24 Set Instrukcja

9 Października 2024
Ozito

Ozito ACP-2115K Instrukcja

9 Października 2024
Anova

Anova CA30S Instrukcja

8 Października 2024
Anova

Anova CA50S Instrukcja

8 Października 2024
DeWalt

DeWalt DCC2520 Instrukcja

8 Października 2024
SPL

SPL Kultube Instrukcja

8 Października 2024