Instrukcja obsługi Primera AP-Code

Primera Niesklasyfikowane AP-Code

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Primera AP-Code (41 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/41

User's Manual

For the most recent version of this manual please visit

http://www.primera.com/ -codesupport ap

Page | 2

Notices: The information in this document is subject to change without notice. NO WARRANTY OF ANY KIND IS

MADE WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. No liability is assumed for errors contained herein

or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.

This document contains proprietary information that is protected by copyright. All rights are reserved. No part of

this document may be photocopied, reproduced, or translated into another language without prior written

consent.

Trademark Acknowledgments: Primera and Primera Eddie are registered trademarks of Primera Technology, Inc.

Windows is a registered trademark of Microsoft Corporation. All other trademarks are the property of their

respective owners.

Revision History

FCC Compliance Statement: This device complies with part 15 of the FCC rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

For Users in the United States: This product is intended to be supplied by a UL listed Direct Plug-In Power Supply

marked "Class 2" or a UL listed ITE Power Supply marked "LPS" with output rated 12VDC, 3A or higher. This

equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of

the FCC Rules. In a domestic environment, this product may cause radio interference, in which case the user may

be required to take adequate measures. This equipment generates, uses, and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

• Re-orient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Use of shielded cables is required to comply with the Class A limits of Part 15 of the FCC Rules. You are cautioned

that any changes or modifications not expressly approved in this manual could void your authority to operate

and/or obtain warranty service for this equipment.

For Users in Canada: This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus

set out on the Radio Interference Regulations of the Canadian Department of Communications. Le present appareil

numerique n'emet pas de bruits radioelectriques depassant les limites applicables aux appareils numeriques de la

class A prescrites dans le Reglement sur le brouillage radioelectrique edicte par le ministere des Communications

du Canada.

050223

Page | 3

Contents

Section 1: Getting Started ............................................................................................................................. 4

1A Choosing a Good Location ................................................................................................................... 4

1B Unpacking and Inspection 5 ....................................................................................................................

1C Assemble your Date Coder 6 ..................................................................................................................

1D Install the ink Cartridge ..................................................................................................................... 17

1E. Set your applicator to Run After Apply Mode ................................................................................... 19

Section 2 How to use AP-CODE ................................................................................................................... 20

2A Tutorial: Create a Tag ........................................................................................................................ 20

2B Touch Screen Overview ..................................................................................................................... 26

2C System Settings .................................................................................................................................. 27

2D Save and Load Tags ............................................................................................................................ 28

2E Adjusting Print Position ...................................................................................................................... 30

2F Create Automated Expiration Dates .................................................................................................. 33

Section 3: Maintenance and Troubleshooting ............................................................................................ 35

3A Cartridge Cleaning Nothing is Printing –............................................................................................ 35

3B Cartridge Storage ............................................................................................................................... 37

3C Tag Removal ....................................................................................................................................... 37

3D Acceptable Print Surfaces .................................................................................................................. 37

Section 4: Technical Support .......................................................................................................................38

Section 5: Technical Specifications ............................................................................................................. 39

Section 6: Certifications and Environmental Policy .................................................................................... 40