Instrukcja obsługi Premier Mounts MM-BE426

Premier Mounts Wsparcie dla płaskich paneli MM-BE426

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Premier Mounts MM-BE426 (2 stron) w kategorii Wsparcie dla płaskich paneli. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
Page 1 Installation Instructions
Installation Instructions
9531-000-041-00
Parts List
MM-CB2
Dual Multi-Monitor Mounting Arm
(Qty 1)
The MM-CB2 is a dual multimonitor mount arm that works with any
2” tubing. Each mounting head provides 90° of omnidirectional tilt.
The mounting heads include both 75x75mm and 100x100mm VESA
mounting patterns. The arm includes integrated cable management
tabs to keep wires and cables protected and organized. The mounting
heads can be horizontally adjusted.
Step 1
1. Slide your mounting arm over the pole and base (Figure 1)
(not included, but should be previously installed).
Determine the position on the pole desired for your mounting arm.
2. Once in desired position,tighten the two (2)
pre-intalled M8 x 6mm set screws in the
holes in the back of the MM-CB2. Tighten
with included allen key (Figure 2).
Step 2
M4 x 10mm Combo Screws
(Qty 8)
Introduction
MM-CB2
(Figure 1)
(Figure 3)
Are you installing to a 75x75mm or
100x100mm VESA moutning pattern?
For 75x75mm, use mounting points A. For
100x100mm use points B in gure 3.
1) Thread the M4 screws to one-half of their
length into the top two mounting holes on
each display, but do not tighten the M4
screws at this time.
Step 3
(Figure 2)
A A
A A
B B
B B
Thread Insert in Flat
Panel or Adapter Plate
M4 Screw Partially
Threaded Into Flat Panel
Keyhole Slot
MM-CB2 Mount
1) Insert the heads of the M4 screws through the keyhole slots on the
mounting head (Figure 5).
2) Insert the remaining two (2) M4x10mm screws, into the bottom mounting
points (Figure 4)
3) Repeat sub-steps 1 & 2 for the second display.
4) Tighten all M4 screws.
Do not overtighten the mounting hardware
Figure 4
Figure 5
Step 4
To adjust the position of your displays horizontally
1. Turn the mounting head adjustment knob counter clockwise until the
mounting head is lose enough to slide easily along the pole.
2. Slide the display (or mounting head) to the desired position.
3. When in place, turn the adjustment head clockwise to tighten it. Make sure
it is completely secure and does not move before you move on to the next
display or nish.
4. Repeat steps for other displays if desired.
Loosen
& Adjust
Tighten
& Secure
5/32” Allen Key
(Qty 1)
Socket Wrench
(Qty 1)
4” Cable Ties (Qty 2)
3100 E. Miraloma Avenue, Anaheim, CA 92806 | 800.368.9700 USA | F 800.832.4888 | www.mounts.com
Unit 3, The Moorings Business Park, Channel Way | Longford, Conventry, CV6 6RH, UK | +44 (0) 2476 644105 | F +44 (0) 2476 644165
Page 2 Installation Instructions
PREMIER MOUNTS
LIMITED LIFETIME WARRANTY
What and Who is Covered by this Limited Warranty and for How Long
Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the
original owner of this product. The limited warranty is valid only for the original purchaser of the product.
What Premier Mounts Will Do
At the sole option of Premier Mounts, Premier Mounts will repair or replace any product or product part that is
defective. If Premier Mounts chooses to replace a defective product or part, a replacement product or part will be
shipped to you at no charge, but you must pay any labor costs.
What is Not Covered; Limitations
PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS, ADAPTERS, DISPLAYS,
PROJECTORS, OTHER PROPERTY, OR PERSONAL INJURY RESULTING, IN WHOLE OR IN PART, FROM
IMPROPER INSTALLATION, MODIFICATION, USE OR MISUSE OF ITS PRODUCTS.
PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. PREMIER MOUNTS
IS NOT RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED
TO, INABILITY TO USE ITS PRODUCTS OR LABOR COSTS FOR REMOVING AND REPLACING DEFECTIVE
PRODUCTS OR PARTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL
OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
What Customers Must Do for Limited Warranty Service
If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to the
address below within thirty (30) days. Proof of purchase (an original sales receipt) from the original consumer
purchaser must accompany all warranty claims. Warranty claims must also include a description of the problem,
the purchaser’s name, address, and telephone number. General inquiries can be addressed to Premier Mounts
Customer Service at 1-800-368-9700. Warranty claims will not be accepted over the phone or by fax.
Premier Mounts
Attn: Warranty Claim
3130 East Miraloma Ave.
Anaheim, CA 92806
How State Law Applies
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS
WHICH VARY FROM STATE TO STATE.
Step 4
To adjust the tension and/or tilt angle of the mounting head:
1) Adjust the mounting head by utilizing the 90 continuous tilt, until it is in the °
desired position.
2) Remove the side and bottom cosmetic cap from the mounting
head (Figure 6)
3) Use the supplied socket wrench to tighten both nuts.
4) The side nut secures the tilt position (Point A), while the bottom nut secures
the pivot (Point B).
Do not overtighten the mounting hardware
A
B
(Figure 6)
Bottom View
Installation Instructions
3100 E. Miraloma Avenue, Anaheim, CA 92806 | 800.368.9700 USA | F 800.832.4888 | www.mounts.com
Unit 3, The Moorings Business Park, Channel Way | Longford, Conventry, CV6 6RH, UK | +44 (0) 2476 644105 | F +44 (0) 2476 644165

Specyfikacje produktu

Marka: Premier Mounts
Kategoria: Wsparcie dla płaskich paneli
Model: MM-BE426

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Premier Mounts MM-BE426, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Wsparcie dla płaskich paneli Premier Mounts

Premier Mounts

Premier Mounts ECM-3763S Instrukcja

21 Września 2024
Premier Mounts

Premier Mounts RTM-L Instrukcja

21 Września 2024
Premier Mounts

Premier Mounts P4263F Instrukcja

21 Września 2024
Premier Mounts

Premier Mounts PRC-LA Instrukcja

21 Września 2024
Premier Mounts

Premier Mounts ECM-3763T Instrukcja

20 Września 2024
Premier Mounts

Premier Mounts EST100 Instrukcja

20 Września 2024
Premier Mounts

Premier Mounts MMA Instrukcja

19 Września 2024
Premier Mounts

Premier Mounts PRC Instrukcja

19 Września 2024
Premier Mounts

Premier Mounts FLIP-B Instrukcja

18 Września 2024
Premier Mounts

Premier Mounts MM-BE426 Instrukcja

18 Września 2024

Instrukcje Wsparcie dla płaskich paneli

Najnowsze instrukcje dla Wsparcie dla płaskich paneli

NEC

NEC PDVWXUN 55 P Instrukcja

15 Października 2024
Insignia

Insignia NS-STV3N1705 Instrukcja

15 Października 2024
One For All

One For All DM 4110 Instrukcja

9 Października 2024
One For All

One For All DM 7220 Instrukcja

9 Października 2024
One For All

One For All DM 2220 Instrukcja

9 Października 2024
Kogan

Kogan KASMM39S12A Instrukcja

9 Października 2024
Kogan

Kogan KATWM70TLMA Instrukcja

9 Października 2024
Kogan

Kogan KADMM46G24A Instrukcja

9 Października 2024
Kogan

Kogan KADMMPCGASC Instrukcja

9 Października 2024
One For All

One For All DM 2210 Instrukcja

9 Października 2024