Instrukcja obsługi PowerPlus POWX0760

PowerPlus Maszyna do piłowania POWX0760

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla PowerPlus POWX0760 (23 stron) w kategorii Maszyna do piłowania. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/23

POWX0760 EN

1 APPLICATION .................................................................................. 4

2 DESCRIPTION ................................................................................. 4

3 PACKAGE CONTENT LIST ............................................................. 5

4 SYMBOLS ........................................................................................ 5

5 GENERAL POWER TOOL SAFETY WARNINGS .......................... 6

5.1 Work area ................................................................................................................ 6

5.2 Electrical safety ....................................................................................................... 6

5.3 Personal safety 6 .......................................................................................................

5.4 Power tool use and care ......................................................................................... 7

5.5 Service ..................................................................................................................... 7

6 ADDITIONAL SAFETY INSTRUCTIONS FOR TABLE SAWS ....... 7

6.1 For both Mitre saw mode and table saw (bench saw) mode: ............................... 7

6.2 When using in Mitre saw mode: ............................................................................. 8

6.3 When using in the table saw (bench saw) mode: .................................................. 8

7 INSTALLATION ................................................................................ 9

7.1 Bench mounting (Fig. 1 & 3) ................................................................................... 9

7.1.1 For the fully-extended feet set up as the high table. .................................................. 9

7.1.2 For the folded feet set up as the low table ................................................................. 9

8 FUNCTIONAL DESCRIPTI ON ......................................................... 9

8.1 Blade guard (Fig. 4, 5 & 6) ...................................................................................... 9

8.2 Maintaining maximum cutting capacity (Fig. 7) .................................................. 10

8 Adjusting the Mitre angle (Fig. 9 & 10) .3 ................................................................. 11

8.4 Adjusting the bevel angle (Fig. 11 & 12) .............................................................. 11

8.4.1 In the Mitre saw mode ............................................................................................. 11

8.4.2 In the table saw mode (Fig. 13) ............................................................................... 11

8.5 Switch action (Fig. 14) .......................................................................................... 11

8.5.1 Switch for the table saw mode (B) ........................................................................... 11

8.6 Adjusting the depth of cut (Fig. 15 - 21) ..............................................................11

9 ASSEMBLY .................................................................................... 11

9.1 Socket wrench storage (Fig. 17) ...........................................................................11

9.2 Table height two-way set up ................................................................................. 12

POWX0760 EN

9.2.1 High table set up (Fig. 18) ....................................................................................... 12

9.2.2 Low table set up (Fig. 19) ........................................................................................ 12

9.3 Installing or removing saw blade ......................................................................... 12

9.4 Adjusting riving knife (ﬁg 25,26 & 27) .................................................................. 12

9.5 Installing and adjusting rip fence (Fig. 28) .......................................................... 13

9.6 Installing and adjusting Mitre gauge (Fig. 35) ..................................................... 14

9.7 Dust bag (Fig 36, 37 & 38) ..................................................................................... 14

9.8 Securing workpiece .............................................................................................. 14

9.9 Setting up the tool in table saw mode ................................................................. 14

9.9.1 Securing the turn table (Fig. 41) .............................................................................. 15

9.9.2 Securing the tool head (Fig. 42) .............................................................................. 15

9.9.3 Releasing the lower limit stopper (Fig. 43) ............................................................... 15

9.9.4 Repositioning the riving knife (Fig. 44) ....................................................................15

9.9.5 Removing the lower blade guard (Fig. 45) ............................................................... 15

9.9.6 Locking the tool head at fully lowered position (Fig. 46) ...........................................15

9.9.7 Turning over the tool (Fig. 48) ................................................................................. 15

9.9.8 Installing the top blade guard (Fig. 49) .................................................................... 15

9.10 Setting up the tool in Mitre saw mode (Fig. 50) ................................................... 16

9.10.1 Removing the top blade guard ............................................................................16

9.10.2 Installing the lower blade guard C ...................................................................... 16

9.10.3 Turning over the tool .......................................................................................... 16

9.10.4 Releasing the tool head from fully lowered position ............................................ 16

9.10.5 Repositioning riving knife (Fig. 51) .....................................................................16

9.10.6 Installing or removing the sub fences R and L (Fig. 52) ...................................... 16

10 OPERATION ................................................................................... 17

10.1 Cutting as mitre saw ............................................................................................. 17

10.1.1 Press cutting ...................................................................................................... 17

10.1.2 Mitre cutting ....................................................................................................... 17

10.1.3 Bevel cut ............................................................................................................ 17

10.1.4 Compound cutting .............................................................................................. 18

10.1.5 Cutting aluminum extrusion (Fig. 56) .................................................................. 18

10.2 Cutting as table saw (bench mode) .....................................................................18

POWX0760 EN

10.2.1 Work helpers ...................................................................................................... 18

10.2.2 Push block (Fig. 57) ........................................................................................... 18

10.2.3 Auxiliary fence (Fig. 58) ...................................................................................... 18

10.2.4 Ripping ............................................................................................................... 19

10.2.5 Cross cutting (Fig. 63) ........................................................................................ 19

10.2.6 Mitre gauge ........................................................................................................ 19

10.2.7 Use of Mitre gauge (Fig. 64) ............................................................................... 19

10.2.8 Auxiliary wood facing (Mitre gauge) (Fig. 65) ...................................................... 19

10.2.9 Carrying tool (Fig. 66) ......................................................................................... 20

11 MAINTENANCE ............................................................................. 20

11.1 Adjusting the cutting angle .................................................................................. 20

11.1.1 Mitre angle ......................................................................................................... 20

11.1.2 Bevel angle ........................................................................................................ 20

11.2 Replacing carbon brushes (Fig. 73 & 74) ............................................................ 21

11.3 After use ................................................................................................................ 21

11.4 Service ................................................................................................................... 21

12 TECHNICAL DATA ........................................................................ 21

13 NOISE ............................................................................................. 22

14 STORAGE ...................................................................................... 22

15 WARRANTY ................................................................................... 22

16 ENVIRONMENT ............................................................................. 23

17 DECLARATION OF CONFORMITY .............................................. 23

Specyfikacje produktu

Marka:	PowerPlus
Kategoria:	Maszyna do piłowania
Model:	POWX0760
Źródło zasilania:	Prąd przemienny
Moc pobierana:	1800 W
Średnica tarczy:	255 mm
Prędkość biegu jałowego (max):	4200 RPM
Poziom mocy dźwięku:	105 dB