Instrukcja obsługi Postium OBM-W420

Postium monitor OBM-W420

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Postium OBM-W420 (32 stron) w kategorii monitor. Ta instrukcja była pomocna dla 22 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/32
Operational Instructions
OBM-W180
OBM-W210
OBM-W240
OBM-W310
OBM-W420
OBM-W460
OBM-W550
User Manual
1706
Professional Video 4K Wall Monitor
OBM W Series
OBM-W Series
4K Wall Monitor
with 12G/6G/3G-SDI
2
Table of Contents
1. Precaution
2. Main Features
3. Location and Function of Parts and Controls
Front Panel
Rear Panel
4. Using the Menu
5. Adjustment Using the Menus
6. OSD Menu Operations
Status Menu
Color Temp/Color Space/Gamma Menu
Zebra/Focus Menu
User Conguration Menu
Remote Menu
Security Menu
7. Scan Mode Image
8. Available Signal Formats
9. Key Functions
10. Product Specications
3
5
6
8
10
11
12
13
15
15
19
20
21
23
25
29
OBM-W Series
4K Wall Monitor
with 12G/6G/3G-SDI
3
1. Precaution
Always use set voltage.
AC 100 ~ 230V, 50/60Hz
DC 12V(OBM-W180/W210/W240) or DC 24V(OBM-W310)
All these instrucons should be read and understood before operang the unit.
If liquid is spilled on or impacts this product, please disconnect the product immediately
and seek professional help before connued use.
Unplug the unit from the wall outlet if it is not to be used for several days or more.
Keep unit in a well-venlated place to prevent overheang.
Do not install the product near any heat-generang equipment. Also, keep the product out of direct sunlight
or dusty areas.
Protect the power cord from being walked on or pinched parcularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
When using other DC 12V(OBM-W180/W210/W240) or DC 24V(OBM-W310) adapters instead of the standard
adapter provided by the manufacturer, please check the proper load capacity or current capacity and use an
adapter with stable voltage.
Do not overload AC outlets or extension cords. Overloading can cause fire or electric shock.
A very small proporon of pixels may be stuck, either always off (black), always on (red, green, or blue), or
flashing. In addion, over a long period of use, because of the physical characteriscs of the liquid crystal
display, such stuck pixels may appear spontaneously. These problems are not a malfuncon.
If a fixed picture such as a frame of a divided picture or me code, or a sll picture is displayed for a long me,
an image may remain on the screen and be superimposed as a ghosng image.
The permanent burn-in may occur for LCD panel if sll images are displayed in the same posion on the
screen connuously, or repeatedly over extended periods.
To reduce the risk of burn-in,
a. Turn off the character displays.
b. Turn off the power when not in use.
c. Turn off the power if the monitor is not to be used for a prolonged period of me.
OBM-W Series
4K Wall Monitor
with 12G/6G/3G-SDI
4
Do not aempt to service the product yourself. Removing covers can expose you to high voltage and other
dangerous condions. Request a qualified service person to perform servicing.
When the product needs replacement parts, make sure that the service person uses replacement parts
specified by the manufacturer, or those with the same characteriscs and performance as the original parts.
Use of unauthorized parts may result in fire, electric shock and/or other danger.
Only clean the product with a noncommercial, mild and neutral detergent.
Do not throw away the carton and packing materials. When transporng the product, make use of its original
packaging for safer carriage.
FCC (Federal Communications Commission)
This equipment has been tested and found to comply with the limits for class A digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protecon against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy, and if not installed and used in accordance with the
instrucon manual, may cause harmful interference to radio communicaons. Operaon of this
equipment in a residenal area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Warning!! : Changes or modificaons not expressly approved by the manufacturer could void the
users authority to operate the equipment.
Disposal of Old Electrical & Electronic Equipment
(Applicable in the European Union and other European countries
with separate collecon systems)
This symbol on the product or on its packing indicates that this product shall not be treated as
household waste. Instead it shall be handed over to the applicable collecon point for the recycling of
electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help
prevent potenal negave consequence for the environment and human health, which could otherwise
be caused by inappropriate waste handling of this product. The recycling of materials will help to
conserve natural resources.
OBM-W Series
4K Wall Monitor
with 12G/6G/3G-SDI
5
2. Main Features
The OBM W series incorporates 12G-SDI input and loopout(x2), HDMI 2.0 input, SFP opcal connector,
Component and Composite on the panel of full HD resoluon. So, the OBM W series is ideal for building up
a 4K monitor wall in the studio or OB van. The OBM W series offers the advanced and convenient features
such as HDR(High Dynamic Range), Ethernet Control, Camera Log display, etc.
· 12G/6G-SDI 2 Channel
· Dual Link 3G-SDI 2-Sample Interleave
· HDMI 2.0 Support
· HDR(High Dynamic Range) Display supporng PQ EOTF(ST 2084), Hybrid Log Gamma, S-Log3
· 3D-LUT for Accurate Color Reproducon
· 1.064 Billion Colors
· Camera Log Conversion
· Camera Log Mapped SDI Loopout
· Custom 3D LUT File Import Through USB
· Gamma Selecon (1.0 ~ 3.0)
· Color Temperature(3200K, 5500K, 6500K, 9300K, USER 1/2/3, DCI-P3)
· Compare Color Sengs (Side by Side, Wipe Posion)
· Waveform, VectorScope (Wave + Vector, Waveform Wide)
· Various Markers (EBU, 4:3, 16:9, 1.85:1, 2.35:1, Variable etc.)
· Internal White Paerns and Color Bar Display for Color Test
· De-embedded 8~16ch Audio Level Meter
· Remote Control via GPI(RJ-45) Port
· HDR Waveform
· 3 Color TALLY Lamp
· Rack & VESA Mount (Opon)
· SFP Opcal Connector
· Monitor Control via Ethernet, RS-422
· Easy Firmware Update by USB
· Focus Assist
· Zebra
· Support 4096x2160 Aspect
· Zero Scan / 1:1 Scan
· H/V Delay
· Aspect
· Freeze
· Blue/Mono Only
· Time Code Display
· IMD
· Closed Capon(608, 708)
· System Data Copy
· Key Lock & Password Lock
OBM-W Series
4K Wall Monitor
with 12G/6G/3G-SDI
6
3. Location and Function of Parts and Controls
A : Input select Buons/Lamp
Press to monitor the signal input to each connector.
[SINGLE] Buon/Lamp
- Press the buon to select SDI input or SFP input for one channel.
- Mode changes in the order of [12G SDI-1], [12G SDI-2], [3G SDI-3], [3G SDI-4], [SFP]*.
*When a SFP module is inserted, [SFP] input can be selected.
[2-S.I.] Buon/Lamp
- Press the buon to select 2-SAMPLE Interleave SDI input signal through two or four SDI input connectors.
- Mode changes in the order of [Dual-Link 2-S.I.], [Quad-Link 2-S.I.].
[ANALOG] Buon/Lamp
- Press the buon to select Analog Input.
- Mode changes in the order of [Composite] [Component].
[HDMI] Buon/Lamp - Press the buon to select HDMI input.
B : F1 ~ F5 Buon/Lamp
Press to adjust or turn on/off the assigned funcon.
The following funcons are assigned at the factory.
[F1]: Color Space Compare
[F2]: H/V Delay
[F3]: Color Temp
[F4]: Audio Level Meter
[F5]: Time Code
C : Funcon Buon/Lamp
Press to adjust or turn/off each funcon.
- Press the buon to adjust the scan mode. (Zero Scan, 1:1 Scan).[SCAN] Buon
[ASPECT] Buon
- Press the buon to select the Aspect Rao of the signal.
- Mode changes in the order of [16:9] [4:3] [2.35;1] [1.85:1] [15:9] [16:10] [AUTO].
- Press the buon to acvate and deacvate the Marker.[MARKER] Buon
[BLUE ONLY] Buon
- Press the buon to acvate and deacvate the Blue Only funcon.
- You may remove R(red) and G(green) from the input signal and play the screen only with B(blue) signal.
This funcon is convenient to adjust Chroma and Phase and to observe the signal noise.
- The buon may be pressed twice to change the screen to MONO mode.
(This mode uses only Luminance value)
[KEY LOCK] Buon - Press the buon to lock all buons except Power.
D : Rotary encoder
[BRIGHT] knob
Press this knob to display the adjustment screen and adjust the picture brightness. Press again to hide the
adjustment screen. Turn the knob right to increase the brightness and turn le to decrease it.
[CONTRAST] knob
Press this knob to display the adjustment screen and adjust the picture contrast. Press again to hide the
adjustment screen. Turn the knob right to increase the contrast and turn le to decrease it.
Front Panel
A B C D E F G
OBM-W Series
4K Wall Monitor
with 12G/6G/3G-SDI
7
[CHROMA] knob
Press this knob to display the adjustment screen and adjust the color intensity. Press again to hide the
adjustment screen. Turn the knob right to increase the color intensity and turn le to decrease it.
[APERTURE] knob
Press this knob to display the adjustment screen and adjust the picture sharpness. Press again to hide
the adjustment screen. Turn the knob right to make the picture sharper and turn it le to make the
picture soer.
E : Menu Operaon Buons
Displays or sets the on-screen menu.
[MENU/RETURN]
- Acvates and deacvates the display of the Main Menu.
- When the on-screen menu is not displayed, if this buon is pressed the main menu is displayed.
When the menu is displayed, press the buon to return to the previous menu.
[SELECT/VOLUME] knob (Menu selecon control)
- When the menu is displayed, turn the knob to select a menu item or a seng value, and then press the
knob to confirm the seng.
- If this knob is pressed when the menu is not displayed, the adjustment screen of [VOLUME] is displayed
to adjust the audio volume.
- Press this knob to change the modes in the order of [Focus Frequency] [Zebra Level] [Line Posion]
[Variable Marker] and adjust each mode’s value.
[Focus Frequency]: When Focus Assist funcon is acvated, this mode is displayed.
[Zebra Level]: When Zebra funcon is acvated, this mode is displayed.
[Line Posion]: When WFM/Vector funcon and Line Select funcon is acvated, this mode is displayed.
[Variable Marker]:
When Marker funcon is acvated and Aspect Marker is set Variable, this mode is displayed.
F : (Standby) switch and indicator
- Press to turn the power on when this monitor is in standby mode. Aer being turned on, the monitor
performs Inializaon and the indicator flashes in green.
- Press the switch again for a second to set the monitor in standby mode. Then, the indi or flashes incat
orange and then turns red. The indicator in orange means that the monitor goes into the standby
mode.
When the indicator flashes in orange, this buon doesn’t work.
G : (headphone) jack & Speaker and USB connector
Headphone jack & Speaker
- The audio signal which is selected using the input select buon is output in stereo sound.
- When SDI signals are input, the audio signals of the channels selected with SDI Audio Seng in the User
Configuraon menu are output.
- When the headphones are connected to the jack, audio signals will not be output.
[USB] Connector
- To update CPU, GPU, FPGA program.
- To connect the monitor with the Color Calibraon program provided by the manufacturer and perform
the color calibraon.
- To connect the monitor with the control program provided by the manufacturer and control funcons
OBM-W Series
4K Wall Monitor
with 12G/6G/3G-SDI
8
Rear Panel
A : SDI IN (SDI Input) connectors (BNC)
Input connectors for SDI signals. For details, see “Connecng the SDI Signals”
B : SDI OUT (SDI Output) connectors (BNC)
Output connectors for SDI signals.
Each connector outputs the signal which is input to the corresponding SDI IN connector.
**Note - Output is acvated only when the power is on. Output is not acvated in standby mode.
C : SFP Input connector
Input connector for SFP opcal signal.
D : HDMI input connectors
Input connectors for HDMI signals.
-
For an HDMI cable, High Speed HDMI Cable with the cable type logo or HDMI 2.0 Cable is recommended.
- When inpung 4K resoluon(3840 x 2160 or 4096 x 2160) signal, use a cable of 3m or less.
E : Analog input connectors
Input connectors for analog signals (CVBS, Component).
F : PARALLEL REMOTE connector(RJ-45, 8-pin)
Forms a parallel switch and controls the monitor externally.
**Note - For safety, do not connect the connector for peripheral device wiring that might have excessive
voltage to this port. Follow the instrucons about this port.
[Pin Assignment]
Funcons can be changed in [Remote] secon of the menu.
CABDEGFIHJK
18
Pin Number Funcon
Single SDI
Analog
2-S.I. SDI
HDMI
1:1 Scan
Aspect
Power
GND
1
2
3
4
5
6
7
8
OBM-W Series
4K Wall Monitor
with 12G/6G/3G-SDI
9
G : SERIAL REMOTE IN/OUT connector (RJ-45)
Used for the future funcon expansion.
Connects the monitor to the control program provided by the manufacturer by using RS-422/485
communicaon or the external UMD(IMD) equipment and controls the monitor.
H : LAN(10/100) IN/OUT connector
Used for the future funcon expansion.
Connects to the LAN (10/100) connector of the network by using 10BASE-T/100BASE-TX LAN cable.
A daisy chain connecon using the LAN input/output connectors enables the control of mulple monitors in
sequence.
I : AUDIO IN connector (Stereo mini jack)
Connector for analog audio input.
Analog input can be selected with SDI Audio Seng in User Configuraon menu.
J : DC IN terminal
Connects the DC power supply to the monitor.
- OBM-W180/W210/W240 : 12V
- OBM-W310: 24V
Make sure to use DC 12V power supply for OBM-W180/W210/W240 and DC 24V power supply for
OBM-W310.
K : AC IN terminal
AC power input connector.
Connects the provided AC power cord.
DC IN Socket
1 : GND
4 : +24V
4
1 2
3
DC IN Socket
1 : GND
4 : +12V
4
1 2
3
OBM-W180/W210/W240 OBM-W310


Specyfikacje produktu

Marka: Postium
Kategoria: monitor
Model: OBM-W420

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Postium OBM-W420, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje monitor Postium

Postium

Postium PRM-207Q Instrukcja

11 Grudnia 2024
Postium

Postium PRM-434 Instrukcja

11 Grudnia 2024
Postium

Postium OBM-L180 Instrukcja

7 Października 2024
Postium

Postium PRM-102F Instrukcja

7 Października 2024
Postium

Postium OBM-W460 Instrukcja

5 Października 2024
Postium

Postium OBM-W240 Instrukcja

5 Października 2024
Postium

Postium OBM-W420 Instrukcja

5 Października 2024
Postium

Postium OBM-U178K Instrukcja

5 Października 2024
Postium

Postium OBM-U550L Instrukcja

27 Września 2024

Instrukcje monitor

Najnowsze instrukcje dla monitor