Instrukcja obsługi POSline ITT4050B

POSline drukarka etykiet ITT4050B

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla POSline ITT4050B (3 stron) w kategorii drukarka etykiet. Ta instrukcja była pomocna dla 14 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/3
Label Printer
Page 1 of 2
Quick Installation Guide
Printer Overview
Setting up the Printer
(1) Connect the printer to the
computer mainframe.
(2) Plug the power cord into the
power jacket at the rear of the
printer.
(3) Plug the power cord into a
properly ground receptacle.
Note: Please switch OFF printer power switch prior to plug in the power cord to printer power jack.
Loading the Ribbon
(1) Place an empty paper core onto
the ribbon rewind spindle.
(2) Insert the left side first. Mount
the ribbon rewind paper core on
the front hubs.
(3) Please be noted that the bigger
hub side with 4 ribs must be
installed toward the right side of
ribbon mechanism.
(4) Install a ribbon on the ribbon
supply spindle. Mount the ribbon
supply spindle on the rear hubs.
(5) Insert the left side first. Please
be noted that the bigger hub
side with 4 ribs must be installed
toward the right side of ribbon
mechanism.
(6) Disengage the printer carriage
by pulling the carriage release
lever upwards.
(7) Following the direction of the
↓
↓
↓
↓↓
RIBBON
label, pull the
transparent ribbon leader to the
front from under the ribbon
mechanism.
(8) Attach the ribbon leader to the
empty paper core on the ribbon
rewind spindle (with a tape).
(9) Rotate the ribbon rewind spindle
until the ribbon overlaps the
ribbon leader and stretches
tight.
Ribbon rewind spindle
Ribbon supply spindle
Printer cover
Ribbon mechanism
Carriage release lever
Label supply spindle
Fixing tab
Print head
Label stripper
Backing paper outlet
Label roll mount
Page 2 of 2
Loading the Label
(1) Insert a label spindle into a paper
roll. Insert fixing tabs into the
spindle.
(2) Place the label onto the
(external) label roll mount.
(3) Install the label so that it goes
(when using an external label
roll mount: through the label
feed slot) in the direction of the
↓
↓
↓
↓↓ LABEL label and under the
ribbon mechanism to lay upon
the platen.
(4) Adjust the label guide to fit the
width of the label.
(5) Engage the printer carriage. (6) Close the printer cover.
Note: When switched on, the printer will automatically
detect whether ribbon is
installed to set printer
to direct thermal or thermal transfer mode. As such, to use thermal transfer mode, be sure to
install the ribbon, the label, and engage the ribbon mechanism before you switch on the printer.
To use direct thermal mode, install the label and engage the ribbon mechanism before switching
on the printer.
Power-on Utilities
Self Test
Power off the printer, install the ribbon and the label first. Press the FEED button and then turn on the printer
power. Do not release the FEED button until the printer feeds labels. The printer performs the following items:
1. Calibrate label pitch.
2. Print out thermal print head check pattern.
3. Print the internal settings.
4. Enter into dump mode.
Gap Sensor Calibration
This utility is used to calibrate the sensitivity of the gap sensor. Users may have to calibrate the gap sensor for
two reasons:
1. Using a new type of label
2. Initializing the printer
Note: The ERROR LED may flash if the gap sensor is not calibrated properly.
Please follow the steps below to calibrate the gap sensor.
1. Turn off printer power and install blank (i.e., without any logos or characters) label roll on the printer power.
2. Hold down the PAUSE button while turning on printer power.
3. Release PAUSE button when the printer feeds labels. Do not turn off printer power until the printer stops
and the two green LEDs light on.
Printer Initialization
Printer initialization sets printer parameters to default values.
Please follow the steps below to initialize the printer:
1. Turn off the printer power.
2. Hold down the PAUSE
and FEED
buttons while turning on the printer power.
3. Do not release the buttons until the three LEDs flash in turn.
Note: When printer initialization is done, please calibrate the gap sensor again.
For further information on printer operation, please refer to the user's manual in driver CD disc.
Specifications, accessories, parts and programs are subject to change without notice.

Specyfikacje produktu

Marka: POSline
Kategoria: drukarka etykiet
Model: ITT4050B

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z POSline ITT4050B, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje drukarka etykiet POSline

POSline

POSline ITT4100 Instrukcja

13 Września 2024
POSline

POSline ITT4050B Instrukcja

5 Lipca 2024

Instrukcje drukarka etykiet

Najnowsze instrukcje dla drukarka etykiet

Dymo

Dymo LabelPoint 150 Instrukcja

15 Października 2024
Dymo

Dymo LabelWriter 450 Turbo Instrukcja

13 Października 2024
Dymo

Dymo LabelManager LM160 Instrukcja

11 Października 2024
Toshiba

Toshiba B-EX4T1-GS12 Instrukcja

10 Października 2024
Brady

Brady M510 Instrukcja

8 Października 2024
Bixolon

Bixolon SLP-TX403 Instrukcja

8 Października 2024
Custom

Custom D4 202 Instrukcja

5 Października 2024
Datamax O'Neil

Datamax O'Neil Compact4 Mark II Instrukcja

5 Października 2024
Datamax O'Neil

Datamax O'Neil RL3 Instrukcja

5 Października 2024
Datamax O'Neil

Datamax O'Neil Mark III E-4305P Instrukcja

4 Października 2024