Instrukcja obsługi Polk PA D4000.4

Polk głośnik PA D4000.4

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Polk PA D4000.4 (34 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/34
4 - C H A N N E L
A M P L I F I E R
PA
D4000.4
HBP2478
2 © 2011 Polk Audio—all rights reserved © 2011 Polk Audio—all rights reserved 3
TABLE OF CONTENTS
INTRODUCTION............................................................................... 3
WHAT’S IN THE BOX .......................................................................... 3
LISTEN CAREFULLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
INTERNAL BRIDGING ......................................................................... 3
TOOLS OF THE TRADE ......................................................................... 4
END PANEL LAYOUTS .......................................................................4 - 5
Line Level Inputs/Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 - 5
Power Inputs/Speaker Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
AMPLIFIER WIRING ........................................................................... 6
Power Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Speaker Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Bridging 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AMPLIFIER INSTALLATION..................................................................... 7
Mounting Locations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Passenger Compartment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Trunk Compartment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
INSTALLATION GUIDELINES .................................................................7 - 8
SET UP AND TROUBLESHOOTING ...........................................................8 - 10
Testing the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 - 9
Adjusting the Sound of the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Troubleshooting Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 - 10
SPECIFICATIONS............................................................................. 11
FRANÇAIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 - 22
ESPAÑOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 - 33
DEUTSCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 - 44
ITALIANO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 - 55
PORTUGUÊS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56 - 66
WARRANTY ................................................................................. 67
ENGLISH
INTRODUCTION
Thank you for your purchase of a Polk Audio PA D Series amplifier. Each PA D Series amplifier is designed
to be the leader in its class offering the most power, advanced features, and extreme ease of use. In high-end
sound systems or high SPL systems, PA D Series amplifiers will give you years of trouble-free performance.
• PA D4000.4—200W x 4 RMS @ 2 Ohms; 125W x 4 RMS @ 4 Ohms; 400W x 2 Bridged @ 4 Ohms.
Note: Improper installation will not only limit the performance of your Polk Audio PA D Series amplifier but also
potentially compromise the reliability of this amplifier. To ensure proper sonic results and component reliability,
please refer to your authorized dealer for installation assistance or advice. If you decide to perform the installation
yourself, be sure to read the entire manual before beginning the installation (see Installation Guidelines on page 7).
RECORD THIS INFORMATION FOR YOUR RECORDS
Model:__________________________________________________
Serial Number:____________________________________________
Date of Purchase:__________________________________________
WHAT’S IN THE BOX
• PolkAudioAmplifier • Owner’s Manual
• PhillipsScrews(4) • Online Registration Card
• TerminalBlockAdaptor
Important Note: If anything is missing or damaged, or if your Polk Audio PA D Series amplifier fails
to operate, notify your dealer immediately. We recommend keeping your original carton and packing
materials in case you need to ship the unit in the future.
WARNING: LISTEN CAREFULLY
Polk Audio amplifiers, loudspeakers and subwoofers are capable of playing at extremely high volume levels,
which could cause serious or permanent hearing damage. Polk Audio accepts no liability for hearing loss,
bodily injury or property damage resulting from the misuse of its products. Keep these guidelines in mind
and always use your own good judgment when controlling volume. For more about safe volume levels,
go to: www.osha.gov/dts/osta/otm/noise/standards_more.html
INTERNAL BRIDGING
Terminals that can be used in bridging mode are identified by the black and white boxes above each terminal.
The two black boxes and the two outlined boxes work together to create an internally bridged hookup.
BRIDGED
BRIDGED
RL FL
RR
REAR
FRONT
FR
RR FR
RL FL
4 © 2011 Polk Audio—all rights reserved © 2011 Polk Audio—all rights reserved 5
TOOLS OF THE TRADE
Listed next are the majority of the tools required to perform an installation. Having the proper tools will make
the installation that much easier.
• Phillipsheadscrewdriver • Solderless,crimp-onconnectorsandacrimpingtool
• Electricdrilland3/16"and1/8"drillbits • Safetyglasses
• Permanentinkmarkerorpencil • DMMorVOM
• Safetyglasses • Nylontiestraps
• Wirestrippersandcutters • Wirecrimper
• Electricaltape • Grommetsforpassingwiresthroughmetalcarwalls
• AmplifierPowerWire
END PANEL LAYOUTS
PA D4000.4 Line Level Inputs/Controls
1. Status LEDs (on top of amplifier): Power and Protection—Power will illuminate to indicate
the amplifier is on and operating normally; protection will illuminate if the amplifier shuts down
due to short circuit, DC offset, or overheating detected by onboard protection circuitry.
Rear Controls
2. Rear Line Level Inputs—accepts line level input from the rear channels of a head unit.
3. Rear Level Control—Adjusts the gain of the rear channels to match the output voltage
from your head unit.
4. (a) Rear High-Pass Frequency Button—When FREQ x 10 is engaged, the crossover’s
range increases to 200Hz - 4kHz.
(b) Rear HPF Control—Adjusts the high pass filter frequency to attenuate frequencies
below the setting on the control.
5. (a) Rear Low-Pass Frequency Button—When FREQ x 10 is engaged, the crossover’s
range increases to 500Hz - 5kHz.
(b) Rear LPF Control—Adjusts the low pass filter frequency to attenuate frequencies
above the setting on the control.
6. Rear BPF, FULL, HPF Switch— Selects full range, high pass filter, or band-pass filter. The BPF setting
allows you to use both the high pass filter and low pass filter, and it is for use with mid-range drivers.
The FULL setting does not attenuate any frequencies and is for full range speaker systems. The HPF
setting attenuates low frequencies and is used with mid-range speakers and tweeters.
7. Channel Mode Switch (ST/4Ch)—Set the switch to 4CH if you are using four channel outputs from your head
unit to the FL, FR, RL, RR inputs on the amplifier. Set the switch to ST (stereo) mode if you are using two channel
outputs from your head unit. In the ST position, the amplifier will take the signal input to the FL and FR inputs
and send the same signals also to the RL and RR amplifier channels.
8. Front BPF, FULL, HPF Switch—Selects full range, high pass filter, or band-pass filter. The BPF
setting allows you to use both the high pass filter and low pass filter, and it is for use with mid-range
drivers. The FULL setting does not attenuate any frequencies and is for full range speaker systems.
The HPF setting attenuates low frequencies and is used with mid-range speakers and tweeters.
L
R
L
R
LPF HPF LE VELLPFHPFLEVEL
HPFBPF
FULL
HPFBPF
FULL
ST4CH
FRONTREAR
X-OVER X-OVER
FREQ x 10
FREQ x 1
FREQ x 10
FREQ x 1
50Hz 500H 50Hz 500Hz z20Hz 400H 20Hz 400Hz z6V 200mV 6V 200mV
CHANNEL
MODE
2 1
2114a 5a 9a 10a
4b 5b 9b 10b6 7 8
3
1
9. (a) Front Low-Pass Frequency Button—When FREQ x 10 is engaged, the crossover’s
range increases to 500Hz - 5kHz.
(b) Front LPF Control—Adjusts the low pass filter frequency to attenuate frequencies
above the setting on the control.
10 (a) Front High-Pass Frequency Button—When FREQ x 10 is engaged, the crossover’s
range increases to 200Hz - 4kHz.
(b) Front HPF Control— Adjusts the high pass filter frequency to attenuate frequencies
below the setting on the control.
11. Front Level Control—Adjusts the gain of the front channels to match the output voltage
from your head unit.
12. Front Line Level Inputs—Accepts line level input from the front channels of a head unit.
PA D4000.4 Power Inputs/Speaker Outputs
1. GND (Ground)—Connect this terminal directly to the metal chassis of the vehicle, using the shortest
 wirenecessarytomakethisconnection.Alwaysusewireofthesamegaugeorlargerthanthe+12Vpower
wire. The chassis connection point should be scraped free of paint and dirt. Use only quality crimped and/or
soldered connectors at both ends of this wire. connect this terminal directly to the vehicle battery DO NOT
ground terminal or any other factory ground points.
2. REM (Remote Turn On)—Thisterminalturnsontheamplifierwhen+12Visappliedtoit.
Connect it to the remote turn on lead of the head unit.
3. +12V Power—Connect this terminal through a or to the positive terminal FUSE CIRCUIT BREAKER
of the vehicle battery or the positive terminal of an isolated audio system battery.
WARNING: Always protect this power wire by installing a fuse or circuit breaker of the appropriate
 sizewithin12"ofthebatteryterminalconnection.
4. Fuse—These fuses (40A & 35A) protect the amplifier against internal electrical damage and are meant
to protect only the amplifier. All other power connections should be fused at the power source.
5. Speaker Output—Connect the speakers here
6. Terminal Adaptor—The adaptor enables the use of cable up to 0000AWG
 forthegroundand+12Vconnections(seeillustrationbelow).
GND 12VREM
40A 35A
RL FL
RR
REAR
FRONT
FR
RR FR
RL FL
1 432 5
6. Terminal Adaptor

Specyfikacje produktu

Marka: Polk
Kategoria: głośnik
Model: PA D4000.4

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Polk PA D4000.4, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje głośnik Polk

Polk

Polk Signature Elite ES50 Instrukcja

10 Października 2024
Polk

Polk Signature Elite ES90 Instrukcja

8 Października 2024
Polk

Polk S-15 Instrukcja

8 Października 2024
Polk

Polk db6501 Instrukcja

4 Października 2024
Polk

Polk ES90 Instrukcja

28 Września 2024
Polk

Polk TL1600 Instrukcja

27 Września 2024
Polk

Polk Atrium 8SDi Instrukcja

24 Września 2024
Polk

Polk T Series Instrukcja

23 Września 2024
Polk

Polk Blackstone TL2600 Instrukcja

23 Września 2024
Polk

Polk PA D4000.4 Instrukcja

23 Września 2024

Instrukcje głośnik

Najnowsze instrukcje dla głośnik

Teufel

Teufel Rockster Air Instrukcja

15 Października 2024
Alpine

Alpine PSS-22WRA Instrukcja

15 Października 2024
Bauhn

Bauhn APPS-0724 Instrukcja

15 Października 2024
Aiwa

Aiwa SP-A100 Instrukcja

15 Października 2024
Harman Kardon

Harman Kardon Citation One Instrukcja

14 Października 2024
Alpine

Alpine 30MC Instrukcja

14 Października 2024
Magnat

Magnat Needle 9000 ALU Instrukcja

14 Października 2024
Pioneer

Pioneer SP-T22A-LR Instrukcja

14 Października 2024
Sharp

Sharp PS-932 Instrukcja

14 Października 2024
Pyle

Pyle PDWR64BTW Instrukcja

13 Października 2024