Instrukcja obsługi Phoenix Gold SD200.2


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Phoenix Gold SD200.2 (8 stron) w kategorii Wzmacniacz samochodowy. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/8
Amplifier Manual
Manuel de l’amplificateur
Features: Caractéristiques:
Model: SD200.2
© 2011 Phoenix Gold • www.phoenixgold.com
High Eciency Full Range Class D Topology
Compact Size for Easy Installation
High and Low Pass Crossovers
Robust Unregulated Power Supply
Surface Mount Component Technology
Panel Mounted RCAs
Direct Insert Power and Speaker Terminals
Audio Precision Quality Control Verication
High Temperature Plexiglass cover
RMD -Remote Monitoring Display Port
Topologie de classe D de gamme complète
Petit format pour faciliter l’installation
Filtres croisés passe-haut et passe-bas
Alimentation électrique robuste non réglementée
Technologie de composant monté en surface
Amplicateurs à couplage RC montés sur des panneaux
Terminaux d’alimentation et de haut-parleurs à insertion directe
Vérication du contrôle de la qualité de la précision audio
Couvercle de plexiglas résistant aux températures élevées
RMD - Entrée De L’achage de Tension a Distance
Amplier Owner’s Manual
© 2011 Phoenix Gold • www.phoenixgold.com
SD200.2 SPECIFICATIONS
Frequency Response: ± 1dB from 20Hz to 20kHz
Signal to Noise Ratio: >100dB
High and Low Pass Crossover: 12dB per Octave
Crossover Range: 40Hz to 400Hz
Bass Boost @ 45Hz: 0 to +18dB
Low Level Input Range: 200 millivolts to 8 volts
Lowest Recommend Load: 2 ohms
Typical Eciency: 70%
Damping Factor: Greater than 200
RMS Power 14.4Vdc ≤ 1% THD 75 x 2 @ 4 ohms Stereo
100 x 2 @ 2 ohms Stereo
200 x 1 @ 4 ohms Bridged
Dynamic Power 14.4Vdc >1% THD 90 x 2 @ 4 ohm Stereo
125 x 2 @ 2 ohms Stereo
250 x 1 @ 4 ohms Bridged
Recommended Fuse Size: 25 amp
Power/Ground Wire Size: 8 Gauge
Dimensions (Includes Mounting Feet): 7.24” L x 6.93” W x 2.0” H
184mm L x 176mm W x 51mm H
Dimensions (Includes Terminals): 7.36” L x 6.93” W x 2.0” H
187mm L x 176mm W x 51mm H
Specifications
© 2011 Phoenix Gold • www.phoenixgold.com
Amplier Owner’s Manual
INPUTS
Connect preamp signal cables from headunit to these inputs.
CROSSOVER FREQUENCY
Controls the crossover point for the speaker outputs.
REMOTE MONITORING DISPLAY (RMD)
Connect optional RMD Voltage Display to this port.
BASS BOOST
Variable bass boost from 0 to +18dB @ 45Hz.
SENS
Used to reach maximum amplier power with a wide variety of headunits.
X-OVER CONFIG
FLAT: Crossovers are turned o
HPF: High pass crossover is on
LPF: Low pass crossover is on
+12V
This must be connected to the fused positive terminal (+12V) of the cars
battery. The fuse must be located within 18 inches of the battery.
REMOTE
This must be connected to switched +12V, usually a trigger wire coming
from the head unit or ignition.
GROUND
This must be connected to the negative terminal of the car’s battery or
bolted to a clean, unpainted part of the chassis of the vehicle.
SPEAKER OUTPUTS
Used to connect the amplier to speakers. SD200.2 minimum impedance
is 4 ohms bridged or 2 ohms stereo. Use Right + and Left - to bridge the
channels.
SD200.2
2 Channel Power Amplifier
INPUT
FREQ
40Hz 40 0Hz
X OVER
LPF FLAT HPF
BASSBOOST
0dB 1 8dB
SENS
MIN MAX
POWER
L
GROUND REMOTE + 12V
FUSE
25A
R
+ 12VR
GROU ND
RMD
NOTE: Visible through the plexiglass cover, a single blue power LED is located in the lower corner of all SD ampliers.


Specyfikacje produktu

Marka: Phoenix Gold
Kategoria: Wzmacniacz samochodowy
Model: SD200.2

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Phoenix Gold SD200.2, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą