Instrukcja obsługi Hifonics Zeus ZRX

Hifonics Wzmacniacz samochodowy Zeus ZRX

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Hifonics Zeus ZRX (14 stron) w kategorii Wzmacniacz samochodowy. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/14

ZRX500.2 / ZRX1200.2

ZRX600.4 / ZRX1000.4 / ZRX2000.4

ZRX1200.1D / ZRX1800.1D / ZRX2400.1D / ZRX3200.1D

INDEX PAGE

General Installation Procedure..........................................................................................................................................................................................1

Amplifier Feature Descriptions...........................................................................................................................................................................................2

ZRX500.2 / ZRX1200.2 2-CHANNEL AMPLIFIER APPLICATIONS.................................................................................................................................3

Full range stereo / mono

ZRX600.4 / ZRX1000.4 / ZRX2000.4 4-CHANNEL AMPLIFIER APPLICATIONS.........................................................................................................4-5

4, 3 and 2 channel operation / front/rear high pass using a 2 channel model for mono sub bass

ZRX1200.1D / ZRX1800.1D / ZRX2400.1D / ZRX3200.1D 1-CHANNEL AMPLIFIER APPLICATIONS............................................................................. 6

Class D Mono

Features and Specifications.............................................................................................................................................................................................. 7

Setting Up Systems After Installation For Best Performance.............................................................................................................................................. 8

Troubleshooting and Diagnostics.......................................................................................................................................................................................9

Product Warranty.............................................................................................................................................................................................................10

The contents of this manual may not be reproduced or copied with out the written consent of MAXXSONICS USA, Inc.

ZEUS HIGH PERFORMANCE AMPLIFIERS

The Zeus ZRX Series products have been designed to a very high level of performance, with features unavailable in

any other product. All of the amplifiers have variable crossovers built in, with added touches such as subsonic

filter, bass equalization and a remote Level control module(some models) that allows subwoofer Level control from

the drivers seat.

To ensure years of listening pleasure, all amplifiers have a built in diagnostic mode that will detect shorted speaker

leads, low impedance, dangerous high temperatures, DC shorts and will shut down the amp to prevent serious

damage.

Check out our videos of new products,

events and technical tutorials at

www.youtube.com/maxxsonicsusainc

GENERAL INSTALLATION PROCEDURE

System Design

Installation

The success of any car stereo system relies on several factors, such as the system design, execution of the installation, and system setup. Please

remember that any system is only as good as its weakest link.

Please remember that higher power systems are not necessarily useful purely for high sound pressure levels, but also to establish a headroom capability, to

reproduce musical peaks cleanly without distortion. Lower power amplifiers will clip earlier than their more powerful cousins, and cause loudspeaker failure when

overdriven, due to the harmonics generated by a clipped signal, thus overheating voice coils.

Amplifiers should be mounted with the fins running horizontally for best convection cooling, to minimize overheating. Purchase the best quality RCA cables you can

afford, for reliability and less engine noise interference in the audio system.

General:

Run the wiring so that RCA cables are at least 18“ away from power and speaker cables. Keep RCA cables away from electrical devices in the vehicle that can cause

electrical noise, such as electric fuel pumps, emission control modules and other on-board electronic modules.

Power and ground connections(see the features matrix on page 7 for proper gauge cables per amplifier):

Use a sufficient gauge power cable and ground cable using the chart below as reference to what size wire you require. Zeus series amplifiers require at least 4 gauge

power wire. In a multi amplifier system, add the total value of the manufacture recommended fusing to get your total system amperage. Some applications may

require multiple runs of power wire to meet the system requirements. In multi amplifier systems it is advisable to mount a large enough fuse right at the battery, and

run one or multiple +12 volt power cables to a fused distribution block near the amplifiers. It is then a simple matter to connect the +12 volt terminal of each amplifier

to the distribution block. During this process, please ensure that the main power fuse is removed to avoid shorting the electrical system. The main fuse must be within

12” of the vehicles battery.

Ground each amplifier with as short a ground lead as possible directly to the vehicle chassis using at least 4 gauge wire or equivalent to the size of the amplifiers’

power wire. Use a ground distribution block, if you wish, but it is extremely important to keep the main ground lead from this distribution block to the chassis as short

as possible , not more than 12“. The ground connection integrity to the chassis is very important, and the best way to achieve a good, solid electrical and mechanical

contact is to use a large round crimp lug, crimped and soldered to the ground cable. The next step is to scrape the paint off the vehicle chassis , slightly larger than

the ground lug, at the connection point. Drill a clearance hole in the chassis, the same size as the lug hole, and use a bolt, spring washer and nut to securely fasten

the ground lug. Use petroleum jelly to coat the bolt/lug connection, to prevent oxidization with time.

TIP: Use the same approach when installing head units, equalizers or any audio equipment for that matter - run short individual grounds from each piece directly to

the vehicle chassis, to minimize ground loops and system noise. All power, ground and speaker connections should be crimped and soldered for reliability. Make sure

that none of the cable insulation can chafe against exposed metal in the vehicle, causing short circuits to the chassis.

Safe connection sequence:

After all cables are run, connect speaker wires to the speakers and amplifiers, then run and plug in RCA cables. Next, connect all power, ground, and remote turn on

leads. Now connect all +12 volt cables to the amplifier/s and distribution blocks and fuse holders. Finally, connect the main +12 volt cable to the battery, with the main

fuse removed, and we are almost ready to power up the system.

Power up the system:

The following procedure may seem like overkill, but there is nothing more frustrating when turning on a system for the first time, and it does not work properly

immediately.

First, make sure the head unit is off, and turn all level controls to minimum (counterclockwise), including the head unit volume control. Set all equalizers to 0 dB (no

boost), and all crossover frequency controls at approximate frequencies, as recommended by the loudspeaker manufacturer. Set all input selector and crossover

switches as required for the application. Remove all amplifier fuses, and insert the main fuse at the battery. If the fuse does not blow, you can insert the fuse in one of

the amplifiers, and we are ready to turn on the system. Turn the head unit on, insert a CD, or select a radio station, and increase the head unit volume control. If the

system sounds fine, turn off the head unit, and install fuses in the remaining amplifiers, one by one, till the complete system is powered up and functioning properly.

It is highly recommended that the amplifier be mounted to a board of MDF or other solid

structure using the 4 mounting screws provided. Avoid mounting the

amplifier to metal as this can introduce noise and other unwanted issues. When mounting

the amplifier, ensure that it is mounted HORIZONTALLY, as shown in the diagram above, for

optimal heat dissipation. Mounting amplifiers to speaker enclosures is not recommended as

this can cause damage to the amplifier components. When choosing a location for

mounting the amplifier, ensure that you check for clearance from wires, gas tank, electrical

devices and brake lines etc.

NOTE: This Matrix is a general rule

of thumb. Please refer to the

manufacturers specific

requirements. ZRX specifications