Instrukcja obsługi Philips MatchLine 32FD9954

Philips monitor MatchLine 32FD9954

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Philips MatchLine 32FD9954 (17 stron) w kategorii monitor. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/17

CORRECTLY INCORRECTLY

Note: the enclosed template can be used for general positioning only

(fig. 1).

Mounting to sheetrock wall

Note: Bracket can only be used with standard 16" spaced wood wall

studs.

Bracket must be positioned so that the bracket is fastened firmly to

studs at each end.

All required hardware is included.

Note: Because the Receiver Unit’s power cord is 6’, when determining the

Display Unit mounting location, the distance to the nearest AC power

outlet must be considered.

&Determine desired location to mount Display Unit.

Within this area, locate the two 16.54" spaced wall studs that must

be used as the Wall Bracket mounting location. (fig. 1 and 2)

éWith the Wall Bracket held in place, ensure it is properly leveled.

Then, mark where the four holes must be drilled. (fig. 2)

Note: Use only the holes in Bracket.

“Remove the Wall Bracket, and using a 13/64" wood drill bit, drill the

four holes. (fig. 3)

‘Reposition the Wall Bracket, and with four lag bolts (fig. 4), secure

into place.Tighten with 13mm or 1/2" socket wrench. (fig. 5)

Note: Do not use plastic wall anchors with these lag bolts.

Note: Lag bolts must be fastened and centered securely into the stud.

Mounting Wall Bracket

fig. 1

fig. 2

420mm /16,54"

60,5mm / 2.38"

fig. 3

fig. 4

fig. 5

English

Mounting to concrete wall

&Determine desired location to mount Display Unit. Use the enclosed

template for alignment purposes. (fig. 1)

éWith the Wall Bracket held in place, ensure it is properly leveled.

Then, mark where the four holes must be drilled. (fig. 4)

“Remove the Wall Bracket, and using a 5/8" masonry drill bit, drill the

four holes. (fig. 2)

‘Insert a concrete anchor (with bolt) into each hole.

(Firmly tighten each bolt.Then, remove the bolts.

§Reposition the Wall Bracket, and with the four bolts (and washers),

secure into place.

Mounting to concrete block wall

&Determine desired location to mount the Display Unit.

Within this area, position the Wall Bracket so that the four end

mounting holes are located over the cavities of the concrete blocks

(refer to Figure 1)

éWith the Wall Bracket held in place, ensure it is properly leveled.

Then, mark where the four holes are to be drilled.

Note: Use only the four outside or end holes in the Bracket.

“Remove the Wall Bracket and reconfirm that the marks made in the

previous step are located in the cavities of the concrete blocks. Re-

locate the marks as required to ensure that they are in the cavities

of the concrete blocks.

‘With a 1/2” masonry drill bit, drill the four holes.

(Hinge the plastic legs of the toggle bolt into the channel of the metal

end of the toggle bolt so it can fit into the 1/2” hole drilled in the

wall (refer to Figure 2).

§Insert the toggle bolt into the hole in the wall and push it in until it

is in the cavity of the block.

èWith the plastic pull ring of the toggle bolt, pull the metal end of the

toggle bolt firmly against the back of the cavity of the concrete block

(refer to Figure 3).

WASHER

Cavities In Block

Fig. 1

Fig. 2

Fig. 3

!While holding the plastic pull ring, slide the plastic retaining sleeve

towards the wall until it fits into the hole in the wall. This will hold

the toggle bolt in the wall while the Wall Bracket is mounted (refer

to Figure 4).

Push down on the lower plastic leg of the toggle bolt and break it off

flush with the wall (refer to Figure 5).

Push up on the upper plastic leg of the toggle bolt and break it off

flush with the wall (refer to Figure 6).

Install the remaining 3 toggle bolts in the remaining holes the same

way that the first one was installed.

Position the Wall Bracket in place and install the four 1/4-20 bolts,

including washers, in each of the outside corner holes. Do not

tighten completely (refer to Figure 7).

Confirm that the Wall Plate is level, then tighten the bolts securely

(refer to Figure 8).

Mounting to metal stud wall

&Determine desired location to mount the Display Unit.

Within this area, locate the two 16.54” spaced metal wall studs that

must be used as the Wall Bracket mounting location.

éLocate the center of both wall studs at the height that the Wall

Bracket is to be mounted.

“With the Wall Bracket held in place, ensure it is properly leveled.

Then, mark where the four holes are to be drilled.

Note: Use only the four outside or end holes in the Bracket

(refer to Figure 1).

‘Remove the Wall Bracket and reconfirm that the marks made in the

previous step are located in the center of the metal wall studs. Re-

locate the marks as required to ensure that they are in the center of

the metal wall studs (refer to Figure 2).

Metal Wall

Studs

Fig. 1

Holes Centered In

Metal Wall Studs

Fig. 2

Fig. 4

Fig. 5

Fig. 6

Fig. 7

Fig. 8

Specyfikacje produktu

Marka:	Philips
Kategoria:	monitor
Model:	MatchLine 32FD9954

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Philips MatchLine 32FD9954, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje monitor Philips

Philips S Line 222S9 Instrukcja

14 Stycznia 2025

Philips 27B2U6903 Instrukcja

3 Stycznia 2025

Philips Evnia 24M1N3200VS Instrukcja

28 Grudnia 2024

Philips Envia 27M1N3500LS Instrukcja

28 Grudnia 2024

Philips 24E1N1100A Instrukcja

24 Grudnia 2024

Philips 27E1N1800AE Instrukcja

24 Grudnia 2024

Philips 27E1N1900AE Instrukcja

24 Grudnia 2024

Philips 27E1N1600AE Instrukcja

24 Grudnia 2024

Philips Evnia 24M2N3200S Instrukcja

24 Grudnia 2024

Philips Evnia 24M2N3201A Instrukcja

24 Grudnia 2024

Instrukcje monitor

Najnowsze instrukcje dla monitor

Acer VG281K Instrukcja

15 Stycznia 2025

Acer V223W Instrukcja

15 Stycznia 2025

Orion R4N55RNF Instrukcja

15 Stycznia 2025

Orion 23REDPH Instrukcja

15 Stycznia 2025

Orion R4N46UNF Instrukcja

15 Stycznia 2025

Orion 21REDPH Instrukcja

15 Stycznia 2025

BenQ G2750HM Instrukcja

14 Stycznia 2025

Hamlet HM27JF-VDR Instrukcja

14 Stycznia 2025

Hamlet HM24JF-VDR Instrukcja

14 Stycznia 2025

Hamlet HM24JF-V Instrukcja

14 Stycznia 2025