Instrukcja obsługi Philco PW6608

Philco Pralki PW6608

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Philco PW6608 (24 stron) w kategorii Pralki. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/24
PW6608
PW6610
Washing Machine
Please read the manual before using the product and please take good care of it.
1Warnings
General Safety
Never place your machine on a carpet
covered floor. Otherwise, lack of airflow
from below of your machine may cause
electrical parts to overheat. This may cause
problems with your washing machine.
If the power cable or mains plug is
damaged you must call Authorized Service
for repair.
Fit the drain hose into the discharge
housing securely to prevent any water
leakage and to allow machine to take in
and discharge water as required. It is very
important that the water intake and drain
hoses are not folded, squeezed, or broken
when the appliance is pushed into place
after it is installed or cleaned.
This product is designed to resume
operating in the event of powering on after a
power interruption. if you wish to cancel
the programme,see “Canclling the
programme”section.
There may be some water in your machine
when you receive it. This is from the quality
control process and is normal. It is not
harmful to your machine.
Always have the installation and repairing
procedures carried out by the Authorized
Service Agent. Manufacturer shall not be
held liable for damages that may arise from
procedures carried out by unauthorized
persons.
First Use
Carry out your first washing process
without loading your machine and with
detergent under “Cottons 90°C” program.
Ensure that the cold and hot water
connections are made correctly when
installing your machine.
If the current fuse or circuit breaker is less
than 16 Amperes, please have a qualified
electrician install a 16 Ampere fuse or
circuit breaker.
While using with or without a transformer,
do not neglect to have the grounding
installation laid by a qualified electrician.
Our company shall not be liable for any
damages that may arise when the machine
is used on a line without grounding.
Keep the packaging materials out of reach
of children or dispose them by classifying
according to waste directives.
Intended use
This product has been designed for home
use.
The appliance may only be used for
washing and rinsing of textiles that are
marked accordingly.
Safety instructions
This appliance must be connected to
an earthed outlet protected by a fuse of
suitable capacity.
The supply and draining hoses must
always be securely fastened and remain in
an undamaged state.
Fit the draining hose to a washbasin or
bathtub securely before starting up your
machine. There may be a risk of being
scalded due to high washing temperatures!
Never open the loading door or remove the
filter while there is still water in the drum.
Unplug the machine and close the tap
Never wash down the appliance with a
water hose! There is the risk of electric
shock!
Never touch the plug with wet hands. Do
not operate the machine if the power cord
or plug is damaged.
For malfunctions that cannot be solved by
information in the operating manual:
Turn off the machine, unplug it, turn off
the water tap and contact an authorized
service agent. You may refer to your local
agent or solid waste collection center in
your municipality to learn how to dispose of
your machine.
If there are children in your
house...
Keep children away from the machine
when it is operating. Do not let them
tamper with the machine.
Close the loading door when you leave the
area where the machine is located.
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge,
unless they have been given supervision or
instruction concerning use of the appliance
by a person responsible for their safety.
when it is not in use.
Children of less than 3 years should be
kept away unless continuously supervised.
3
2 Installation
Removing packaging
reinforcement
Tilt the machine to remove the packaging
reinforcement. Remove the packaging
reinforcement by pulling the ribbon.
Opening the transportation locks
Transportation safety bolts must be
removed before operating the washing
machine! Otherwise, the machine will be
damaged!
1. Loosen all the bolts with a spanner until
they rotate freely (“C”)
2. Remove transportation safety bolts by
turning them gently.
3. Fit the covers (supplied in the bag with the
Operation Manual) into the holes on the
rear panel. (“P”)
Keep the transportation safety bolts in
a safe place to reuse when the washing
machine needs to be moved again in the
future.
Never move the appliance without the
transportation safety bolts properly fixed in
place!
Adjusting the feet
Do not use any tools to loosen the lock
nuts. Otherwise, they can be damaged.
1. Manually (by hand) loosen the lock nuts on
the feet.
2. Adjust them until the machine stands level
and firmly.
3. Important: Tighten all lock nuts up again.
Connecting to the drain
The water discharge hose can be attached to
the edge of a washbasin or bathtub. The drain
hose should be firmly fitted into the drain as to
not get out of its housing.
Important:
The end of the drain hose must be directly
connected to the wastewater drain or to
the washbasin.
The hose should be attached to a height of
at least 40 cm, and 100 cm at most.
In case the hose is elevated after laying it
on the floor level or close to the ground
(less than 40 cm above the ground), water
discharge becomes more difficult and the
Connecting to the water supply.
Important:
to run the machine must be 1-10 bar (0,1–1,0
MPa).Attach a pressure-reducing valve if the
water pressure is higher than the requirement.
machine to the water intake valves on the
machine.
When returning the appliance to its
place after maintenance or cleaning,
care should be taken not to fold,
squeeze or block the hoses.
The new hose-sets supplied with the appliance
are to be used and that old hose-sets should
not be reused.
The water supply pressure required to run the
Connect the special hoses supplied with the
Open the taps completely after making the
hose connection to check for water leaks at
the connection points. If any leaks occur, turn
off the tap and remove the nut. Retighten the
nut carefully after checking the seal. To prevent
water leakages and damages caused by them,
keep the taps closed when the machine is not in
use.
Models with a single water inlet should not be
connected to the hot water tap.
Laundry may be damaged or the appliance
may switch to protection mode and not work.


Specyfikacje produktu

Marka: Philco
Kategoria: Pralki
Model: PW6608

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Philco PW6608, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Pralki Philco

Philco

Philco PW6610 Instrukcja

12 Października 2024
Philco

Philco PW3608N Instrukcja

11 Października 2024
Philco

Philco PTL8712D Instrukcja

8 Października 2024
Philco

Philco PWS81400V Instrukcja

8 Sierpnia 2024

Instrukcje Pralki

Najnowsze instrukcje dla Pralki

Whirlpool

Whirlpool VAW558P Instrukcja

15 Października 2024
Indesit

Indesit IWCN 61051X9 EU Instrukcja

15 Października 2024
Blomberg

Blomberg WNF 7466 AC20 Instrukcja

15 Października 2024
Whirlpool

Whirlpool AWO/D 41410 Instrukcja

15 Października 2024
Bosch

Bosch WAT28640NL Instrukcja

15 Października 2024
Whirlpool

Whirlpool AWM 5063 Instrukcja

15 Października 2024
Speed Queen

Speed Queen FA3510 Instrukcja

15 Października 2024
Hisense

Hisense HWFM8012 Instrukcja

15 Października 2024
Freggia

Freggia WIE148 Instrukcja

15 Października 2024
Zanussi

Zanussi ZWF 12070 S1 Instrukcja

14 Października 2024