Instrukcja obsługi Petsafe 62350


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Petsafe 62350 (2 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/2
131203
Pet Safety Seat
Care & Use Guide
Thank you for purchasing the Solvit Pet Safety Seat. Check to make sure the contents include a fabric cover with
tether in polybag; a three-panel plastic main Seat section; and the following plastic sections: Front Strut; Rear Strut;
Right Wall; and Left Wall (name embossed on the side of each).
Assembly: (Make sure the smooth side of each plastic panel faces “inand the side with round depressions faces
“out”). Insert tab A on Front Strut into slot A in Left Wall and slide Front Strut in the direction of the arrow until tab
A is in the fully locked position.
Repeat this procedure to lock tab B on Front Strut into slot B on Right Wall, and to lock tabs C and D on Rear Strut
into slots C and D on the Left and Right Wall sections.
The main Seat section is a three-panel piece that was
folded in a “Z” shape in the package. Before
connecting to the Left and Right Wall sections, fold
the Seat section into a “Ushape with the smooth
sides facing “in”. Insert double-tab E on the front
panel of the Seat section into slot E on the Left Wall
and slide to lock. Repeat for tab G then repeat for
tabs F and H into the corresponding slots on the
Right Wall.
Place the assembled plastic frame upside-down on a clean surface. The
Outer Fabric Shell has a zipper and small tags marked Z (next to zipper)
and X (on opposite seam). With zipper in the fully open position, slide the
fabric shell over the plastic frame so the Z seam aligns with the H corner at
the back of the plastic frame and the X seam aligns with the G corner.
SOLVIT Products, LP 1114 W Harris Rd, Suite 101 Arlington, TX 76001
Tel: 866-6-SOLVIT (866-676-5848) Fax: (817) 466-2291
Email: customerservice@solvitproducts.com www.solvitproducts.com
Pull the sides of the fabric shell down all four sides of the plastic frame
until the rectangular bottom panel of the fabric shell aligns with the
rectangular bottom of the plastic frame.
Turn the entire assembly right-side-up and pull the fabric shell up and
over the top edges of the plastic seat, and close the zipper. The seat
should now look like the image below and the two seat belt slits in the
fabric shell should align with the holes in the plastic frame.
The underside of the Top Fabric Liner includes two small
tags marked X and Z. Insert the top liner into the seat
portion of the plastic frame so the X and Z seams on the
inner liner align with the X and Z seams on the fabric outer
shell. Fit the upper edge of the fabric liner over the rear
wall of the plastic frame and fasten the loop tape pieces on
the top liner with the hook tape pieces on the outer shell.
Pass the large loop end of the safety tether (opposite the
carabineer), through the slit sewn into the lower edge of
the back panel of the top liner and through the slit in the
plastic Seat section. Fit the upper edges of the other
three sides of the top liner over the edges of the plastic
frame and fasten the hook and loop tape strips for each
side. Finally, insert the reversible pillow.
To install in vehicle, place the Safety Seat on the vehicle
seat and pass the seat belt through the holes in the fabric and plastic frame on one side of the Safety Seat. Thread the
seat belt through the large loop on the end of the safety tether, all the way through the frame and out the holes on the
opposite side, then buckle. Tug the safety tether firmly to make sure it is attached to the seat belt and adjust to desired
length. Place pet in the Safety Seat, attach the tether, and it’s ready to go! For multiple pets, extra tethers are
available – contact Solvit customer service at the number below.
Safety: We recommend using a harness, rather than a collar, when traveling. The safety tether can be attached to any
harness, but for maximum safety, we recommend the Solvit Deluxe Vehicle Safety Harness, sold separately.
Cleaning: Fabric pieces can be machine washed in cold - machine dry without heat or line dry.
Limited Lifetime Warranty: The Pet Safety Seat is warranted to be free from defects in materials or workmanship for
the life of the product. Some restrictions apply, so please visit our website for more details. A copy of the original
sales receipt is required for warranty issues.
Solvit Products is dedicated to offering innovative solutions to improve pets’ quality of life. Please feel free to
contact us with and questions, comments, or warranty issues. Thank you for your purchase!


Specyfikacje produktu

Marka: Petsafe
Kategoria: Niesklasyfikowane
Model: 62350

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Petsafe 62350, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Niesklasyfikowane Petsafe

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024