Instrukcja obsługi Peerless-AV UltraView UV862

Peerless-AV telewizor UltraView UV862

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Peerless-AV UltraView UV862 (24 stron) w kategorii telewizor. Ta instrukcja była pomocna dla 15 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/24
12020-01-13 #:180-9138-1
ULTRAVIEW™ UHD OUTDOOR TELEVISION
User Guide
ENG
22020-01-13 #:180-9138-1
SYSTEM INSTALLATION AND ELECTRICAL REQUIREMENTS
Electrical Code
Note: To the display system installer: This reminder is provided to call attention to Article 820-44 of
the National Electric Code that provides guidelines for proper grounding and, in particular, species
that the cable ground shall be connected to the grounding system of the facility. Outlet shall be
installed near the equipment and shall be easily accessible.
Antenna discharge unit
(NEC Section 810-20)
NEC National Electric Code
Ground clamp
Electric service
equipment
Ground clamps
Power service grounding
electrode system
(NEC Art 250 Part H)
Grounding conductors
(NEC Section 810-21)
Antenna lead-in wire
Power Source
The display must be connected to a mains socket outlet with a protective grounding connection.
The mains plug is used as the disconnect device and shall remain readily accessible.
Electrical installation shall be in accordance with the applicable parts of Chapter 8 of ANSI/NFPA70.
An outdoor antenna should not be located near overhead electrical lines or any electrical circuits.
If an outside antenna is connected to the receiver, conrm that the antenna system is grounded to
protect against voltage surges and built up static charges. Section 810 of the National Electric Code,
ANSI/NFPA No 70-1984, provides information with respect to proper grounding for the mast and
supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding
connectors, location of antenna discharge unit, connection to grounding electrodes and requirements
for the grounding electrode.
This display operates on 100-240 volts 50-60 Hz, AC current. Insert the power cord into a 120 volt
60 Hz outlet. Never connect the display to direct current or anything other than the specied voltage.
To prevent electric shock from the display, do not use with an extension cord, receptacle, or other
outlet unless the blades and ground terminal can be fully inserted to prevent blade exposure.
All secondary lines must be routed through grounded conduit and kept separate from AC line.
Note: Installation shall incorporate UL Listed external surge protection rated 2500 Vpk or less, for 150
to 300 Vac mains, installed in accordance with Article 285 of ANSI/NFPA 70 or applicable local codes.
32020-01-13 #:180-9138-1
Relevant Information
Record your display's model and serial number here for future reference. Keep this user manual in an
accessible location in the event service is required.
Note: Your display's serial number can be found on the box and underneath the rear cover plate.
Model Number ____________________________________
Serial Number ____________________________________
FCC CAUTION
To assure continued compliance and possible undesirable interference, ferrite cores may be used
when connecting this display to video equipment; maintain at least 400mm (15.75 inches) spacing to
other peripheral devices.
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rule. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with these instructions,
may cause harmful interference to radio communications; however, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment o󰀨
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit di󰀨erent from that to which the receiver is
connected.
4. Consult the dealer or an experienced radio/display technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
• This device may not cause harmful interference.
• This device must accept any interference received, including interference that may cause
undesired operation.
Safety Compliance

Specyfikacje produktu

Marka: Peerless-AV
Kategoria: telewizor
Model: UltraView UV862

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Peerless-AV UltraView UV862, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje telewizor Peerless-AV

Peerless-AV

Peerless-AV UltraView UV491 Instrukcja

21 Maja 2024
Peerless-AV

Peerless-AV UltraView UV862 Instrukcja

11 Maja 2024

Instrukcje telewizor

Najnowsze instrukcje dla telewizor

Mitsubishi

Mitsubishi LCD-A40XS1000 Instrukcja

25 Października 2024
Mitsubishi

Mitsubishi LCD-A32BHR10 Instrukcja

25 Października 2024
Sencor

Sencor SLE 65MUS700TCSB Instrukcja

25 Października 2024
Sencor

Sencor SLE 43US700TCS Instrukcja

25 Października 2024
Sencor

Sencor SLE 40F18TCS Instrukcja

25 Października 2024
Samsung

Samsung QN75Q60AAP Instrukcja

23 Października 2024
Samsung

Samsung UE55ES6550S Instrukcja

23 Października 2024
Samsung

Samsung UE40ES6550S Instrukcja

23 Października 2024
Samsung

Samsung UE46F6650AB Instrukcja

23 Października 2024
Blaupunkt

Blaupunkt 75UBC8000D Instrukcja

20 Października 2024