Instrukcja obsługi Peerless-AV Neptune

Peerless-AV Telewizja Neptune

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Peerless-AV Neptune (72 stron) w kategorii Telewizja. Ta instrukcja była pomocna dla 14 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/72
12020-11-24 #:180-9152-3 (2020-01-20)
User Guide
ENG
22020-11-24 #:180-9152-3 (2020-01-20)
SYSTEM INSTALLATION AND ELECTRICAL REQUIREMENTS
Electrical Code
Note: To the display system installer: This reminder is provided to call attention to Article 820-44 of
the National Electric Code that provides guidelines for proper grounding and, in particular, species
that the cable ground shall be connected to the grounding system of the facility. Outlet shall be
installed near the equipment and shall be easily accessible.
Antenna discharge unit
(NEC Section 810-20)
NEC National Electric Code
Ground clamp
Electric service
equipment
Ground clamps
Power service grounding
electrode system
(NEC Art 250 Part H)
Grounding conductors
(NEC Section 810-21)
Antenna lead-in wire
Power Source
The display must be connected to a mains socket outlet with a protective grounding connection.
The mains plug is used as the disconnect device and shall remain readily accessible.
Electrical installation shall be in accordance with the applicable parts of Chapter 8 of ANSI/NFPA70.
An outdoor antenna should not be located near overhead electrical lines or any electrical circuits.
If an outside antenna is connected to the receiver, conrm that the antenna system is grounded to
protect against voltage surges and built up static charges. Section 810 of the National Electric Code,
ANSI/NFPA No 70-1984, provides information with respect to proper grounding for the mast and
supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding
connectors, location of antenna discharge unit, connection to grounding electrodes and requirements
for the grounding electrode.
These displays operate on 120 volt 60 Hz, AC current. Insert the power cord into a 120 volt
60 Hz outlet. Never connect the display to direct current or anything other than the specied voltage.
To prevent electric shock from the display, do not use with an extension cord, receptacle, or other
outlet unless the blades and ground terminal can be fully inserted to prevent blade exposure.
All secondary lines must be routed through grounded conduit and kept separate from AC line.
Note: Installation shall incorporate UL Listed external surge protection rated 2500 Vpk or less, for 150
to 300 Vac mains, installed in accordance with Article 285 of ANSI/NFPA 70 or applicable local codes.
32020-11-24 #:180-9152-3 (2020-01-20)
Relevant Information
Record your display's model and serial number here for future reference. Keep this user manual in an
accessible location in the event service is required.
Note: Your display's serial number can be found on the box and underneath the rear cover plate.
Model Number ____________________________________
Serial Number ____________________________________
FCC CAUTION
To assure continued compliance and possible undesirable interference, ferrite cores may be used
when connecting this display to video equipment; maintain at least 400mm (15.75 inches) spacing to
other peripheral devices.
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rule. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with these instructions,
may cause harmful interference to radio communications; however, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment o󰀨
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit di󰀨erent from that to which the receiver is
connected.
4. Consult the dealer or an experienced radio/display technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
• This device may not cause harmful interference.
• This device must accept any interference received, including interference that may cause
undesired operation.
42020-11-24 #:180-9152-3 (2020-01-20)
Read before operating equipment
Thank you for purchasing our product. Before using it, please read this user guide carefully and follow
the instructions for safe operation. Please keep this manual for future reference and always include it
when transferring or transporting this product to a di󰀨erent location.
GENERAL SAFETY PRECAUTIONS
In case of emergency such as re or electric shock caused by the product, immediately contact 911
or proper emergency police/re service agencies in your country.
To reduce the risk of electric shock or re, heed the following:
• In case of product malfunction or unusual events such as electrical burning smell, smoke, or
loss of content signals due to internal overheating, immediately turn o󰀨, unplug the electrical
cord and contact the manufacturer.
• Do NOT disassemble, modify or service product in any way other than that contained in this
instruction. Any unauthorized modications made to the product automatically void product
warranty.
• Do NOT touch antenna lines or wires, electrical cables or plugs when lightning or thunder is
present or with wet hands
• Do submerge in water.NOT
• Do NOT destroy, process, or place close to any heat source.
• Do NOT install near poisonous gas or chemically unstable atmosphere.
• Do NOT install near strong magnetic or electrical current eld.
• Do NOT install the product in unstable locations or near moving objects, constantly vibrating
equipment, or uneven surfaces.
• Do NOT leave any re source, such as candles, close to or on the product.
• Do NOT operate the product if it has been dropped or struck. Severe physical impact to the
product may cause components to fall out of place within and break.
• Do NOT bend or twist electrical cords, electrical plugs, cables, or wires with excessive force.
• Do NOT block ventilation slots or place any heavy object on the product.
• Use properly rated electrical voltage.
• Do NOT use any electrical sockets or power strips with many other devices jointly plugged
in. Use a single, directly dedicated and rated GFCI electrical outlet for the product for safe
operation.
• Do NOT move or transport with any cables (electrical, content connectivity) plugged in to the
source devices.
• Always connect the electrical plug rmly and completely. When disconnecting any cables,
always pull on the plug and not the cord.
• Always leave the power o󰀨 when plugging or unplugging the electrical cords or connection
cables.
• Do not defeat the safety purpose of the polarized or grounding type electrical plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two blades and
a third grounding prong. The wide blade or the third prong are provided for your safety. If the
provided plug does not t into your outlet, consult an electrician for replacement of the obsolete
outlet.
• Protect the electrical cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
To avoid personal injury, this appliance must be grounded and wall mounted according to installation
instructions.
WARNING
52020-11-24 #:180-9152-3 (2020-01-20)
WARNING
• Never apply pressure to the exterior of the LCD screen.
• If monitor or glass is broken, do not come in contact with the liquid crystal and handle with care.
• Do NOT climb on the product.
• Do NOT install within ve feet from a body of water.
• Do NOT use if ambient air temperature exceeds the operating limits; Maximum operating
temperature is -22°F ~ 122°F (-30°C ~ 50°)
• The product is intended for outdoor, shaded operation. Place the TV in an area that never
receives direct sunlight, such as under canopy or on the side of a structure. Placing the TV in
direct sunlight will decrease the panel life and void the warranty.
• Do NOT install in enclosure or recessed cavity with less than 2 inches of airow around the
display. Air inside fully encased display must be ventilated.
• The product is to be secured to building before operation.
• Product must be carried and supported by at least two persons.
• Periodically clean dust o󰀨 the electrical plug to keep it clean and dry, ensuring proper and safe
operation.
• Only use attachments/accessories specied by the manufacturer.
62020-11-24 #:180-9152-3 (2020-01-20)
System Installation And Electrical Requirements 2 ..................................................................................
Electrical Code 2 ...............................................................................................................................
Power Source 2 ................................................................................................................................
FCC Caution 3 ...................................................................................................................................
FCC Statement 3 ...............................................................................................................................
Relevant Information 3 .....................................................................................................................
General Safety Precautions ...................................................................................................................4
Set Up Instructions 7 .................................................................................................................................
Parts List ........................................................................................................................................7
Removing I/O Terminal Cover 8 ........................................................................................................
Connecting Cords 9 ...........................................................................................................................
Installing IR Repeater 9 ....................................................................................................................
freePath Technology ......................................................................................................................9
Replacing I/O Terminal Cover.......................................................................................................10
Cable Management ......................................................................................................................11
Prepare The Display For Mounting ..............................................................................................12
Connecting To The Power Source ................................................................................................13
Remote Control Battery Installation And Replacement 14 ................................................................
Operating Instructions 15 ..........................................................................................................................
Power On/O󰀨 the Display .............................................................................................................15
Onboard Controls 15 .........................................................................................................................
Navigating The On-Screen Menu ................................................................................................16
Picture .................................................................................................................................16
Sound ..................................................................................................................................16
Time ....................................................................................................................................16
Setup ...................................................................................................................................17
Lock .....................................................................................................................................17
Channel ...............................................................................................................................17
Media Functionality 18 .....................................................................................................................
Compatible Media 20 ........................................................................................................................
(RS-232C) Serial Control Of The TV 22 ...........................................................................................
Maintenance ........................................................................................................................................23
Care Of Screen 23 ...........................................................................................................................
Mobile Telephone Caution ...........................................................................................................23
End Of Life Directives 23 ..................................................................................................................
Warranty ..............................................................................................................................................24
CONTENTS
72020-11-24 #:180-9152-3 (2020-01-20)
SET UP INSTRUCTIONS
Parts List
Description Qty
Atelevision 1
Bremote control 1
Cadhesive cable holder 3
DIR repeater 1
Euser guide (not shown) 1
Ftechnical support insert (not shown) 1
Gwarranty registration card (not shown) 1
A (1)
television
B (1)
remote control
D (1)
IR repeater
POWER
TV
TV/SPK
SPK
1 32
4 65
7
•
9
LAST
8
0
OK
AUX1 AUX2
MUTE
VOL
MENU
GUIDE
CH
INFO
INPUT
EXIT
C (3)
cable tie holder
82020-11-24 #:180-9152-3 (2020-01-20)
Removing I/O Terminal Cover
Remove I/O terminal cover and (8) screws to access source connection panel.
A
92020-11-24 #:180-9152-3 (2020-01-20)
Connecting Cords
freePath Technology
Using freePath Technology, the I/O terminal cover allows for better WiFi signal penetration for network
connectivity of Smart TV devices stored within the I/O terminal compartment
Connect source devices to appropriate display input. Make all connections prior to powering on the
display.
HDMI 2
HDMI 3
RS232
IR Repeater
USB 1 + 2
Antenna/Cable
HDMI 1
(ARC)
Audio Out
S/PDIF Optical
Audio In
Component In
CVBS
Installing IR Repeater (Optional)
D
Insert the 3.5mm end of the included 5V IR
repeater into the IR Repeater port on the input
panel of the display. IR Repeater port may not be
compatible with other 3 rd party repeaters.
10 2020-11-24 #:180-9152-3 (2020-01-20)
Replacing I/O Terminal Cover
1. Run cables through bottom of I/O terminal cavity across foam gasket. All cables must exit toward
bottom of display to retain seal when I/O terminal cover is installed. Do not run cabling through
the top or sides of I/O terminal cavity. Leave approximately 1/2" (13mm) between cables to
retain seal when I/O Terminal Cover is installed.
2. Replace I/O terminal cover onto I/O terminal guides, keeping cables between the bottom
gaskets.
3. Replace and-tighten (8) screws until I/O terminal cover gasket is fully compressed to back of
display.
CAUTION
Failure to follow these instructions can result in the product being damaged, destroyed, and
voiding the warranty.
• Ensure cord bend radius does not exceed limits set by
the manufacturer.
• Ensure cords are seated properly in the cable channels
to avoid potential damage to cords when I/O terminal
cover is installed.
• Do not run cables through the top or sides of I/O terminal
cavity. All cables must exit toward bottom of display to
retain seal when I/O terminal cover is installed.
CAUTION
Do not overtighten screws
guides
Replace
guides
11 2020-11-24 #:180-9152-3 (2020-01-20)
Cable Management
Secure cables to display with adhesive cable holders.
C (3)
C
12 2020-11-24 #:180-9152-3 (2020-01-20)
B
D
Required
Mounting Screws
(4) M8 screws
(17.4mm long)
Size A B C D E F
55" 11.81"
(300mm)
7.87"
(200mm)
18.65"
(474mm)
4.61"
(117mm)
1.61"
(41mm)
3.11"
(79mm)
65" 11.81"
(300mm)
7.87"
(200mm)
22.89"
(582mm)
5.42"
(138mm)
1.61"
(41mm)
3.11"
(79mm)
75" 15.75"
(400mm)
7.87"
(200mm)
25.27"
(642mm)
7.45"
(189mm)
2.00"
(51mm)
4.01"
(102mm)
REAR VIEW SIDE VIEW
A
F
C E
Prepare The Display For Mounting
Install cords to your display before mounting. Input panel may be obstructed once the display is
mounted.
For your safety, only install on an outdoor-rated mount that is suitable for the application and supports
the weight of the display. When mounting a display outdoors, use environmentally rated mounts to
ensure longevity in harsh environments.
Examine the chart below to determine the mounting specications for your display.
13 2020-11-24 #:180-9152-3 (2020-01-20)
Prepare The Display For Mounting
Size A B C D E
55" 49.09"
(1247mm)
28.54"
(725mm)
47.69"
(1211mm)
26.85"
(682mm)
54.64"
(1388mm)
65" 57.59"
(1463mm)
33.31"
(846mm)
56.24"
(1428mm)
31.62"
(803mm)
64.53"
(1639mm)
75" 66.29"
(1684mm)
38.18"
(970mm)
65.16"
(1655mm)
36.74"
(933mm)
74.52"
(1893mm)
FRONT VIEW
C
A
B D
E
Connect To The Power Source
Connect power cord to GFCI outlet.
14 2020-11-24 #:180-9152-3 (2020-01-20)
Remote Control Battery Installation and Replacement
1. To remove the battery module of the remote
control, remove the two screws on the end
of the battery module. Slide the battery
module out of the remote control.
2. Insert two new “AAA” size batteries into
the battery module. Ensure the positive
and negative marks on the batteries are
correctly oriented with the markings on
the inside of the remote control's battery
compartment.
3. Slide the battery module back into the
remote control, and reinsert the two screws
in the end of the battery module to maintain
a waterproof seal (do not over tighten).
The remote control is powered by two 1.5V AAA batteries installed at the factory.
If the Red LED light on the remote fails to illuminate when a button is pressed, the batteries may need
to be replaced. Follow the directions below to replace the batteries.
CAUTION
Incorrect usage of batteries can result in leaks
or bursting. Peerless-AV recommends the
following battery use:
• Do not mix battery brands.
• Do not combine new and old batteries. This
can shorten the battery life or cause battery
acid leaks.
• Remove dead batteries immediately to
prevent battery acid from leaking into the
battery compartment.
• Do not touch exposed battery acid as it
may injure skin.
• Remove the batteries if you do not intend
to use the remote control for a long period
of time.
• Do not expose the batteries to excessive
heat from sunlight, re or other heat
sources or batteries could explode.
• Fully tighten screws to maintain the ingress
protection rating of the remote.
B
POWER
TV
TV/SPK
SPK
1 32
4 65
7
•
9
LAST
8
0
OK
AUX1 AUX2
MUTE
VOL
MENU
GUIDE
CH
INFO
INPUT
EXIT
POWER
TV
TV/SPK
SPK
1 32
4 65
7
•
9
LAST
8
0
OK
AUX1 AUX2
MUTE
VOL
MENU
GUIDE
CH
INFO
INPUT
EXIT
15 2020-11-24 #:180-9152-3 (2020-01-20)
POWER
TV
TV/SPK
SPK
1 32
4 65
7
•
9
LAST
8
0
OK
AUX1 AUX2
MUTE
VOL
MENU
GUIDE
CH
INFO
INPUT
EXIT
Power On/O The Display
Power on your display by using the remote control or the rear power button on the side of the display.
The display will power on but image may not appear for several seconds as it completes its power up
sequence.
Point the remote control at the IR sensor located
below the Peerless-AV logo at the center of the
display, and press the power button.
OPERATING INSTRUCTIONS
Menu Mode Direct Mode
On/O󰀨 On/O󰀨
OK Input Select
Menu Menu
Up Channel Up
Down Channel Down
Right Volume Up
Left Volume Down
Onboard Controls
Direct Mode: Allows for quick access to source selection, volume settings and channel selection.
Menu Mode: Press the Menu button to access Menu Mode and activate the On Screen Display
(OSD). For a description of OSD operation refer to the next section.
The keypad buttons are assigned as indicated in the table below.
VOL
M
CH
16 2020-11-24 #:180-9152-3 (2020-01-20)
Navigating The On Screen Menu
Navigate Enter Exit Return
OK EXIT MENU
TV/SPK
1 32
4 65
7
•
9
LAST
8
0
OK
MUTE
VOL
MENU
CHINFO
INPUT
EXIT
Sound
Sound Mode Standard
Music
Movie
Sports
Custom
Balance L50 ~ R50
Digital Audio PCM / Raw / O
Surround On / O
AVL On / O
Time
Sleep Timer o
5 min
10 min
15 min
30 min
60 min
90 min
120 min
180 min
240 min
Time Zone East
Central
Mountain
Pacic
Alaska
Hawaii
Atlantic
Daylight Savings
On / O
Time Format 12-hour
24-hour
Auto Clock On / O
Picture
Picture Mode Standard
Mild
Vivid
User
Color Temp. Cool
Standard
Warm
Advanced Settings
Aspect Ratio Cinema
Zoom
Point to Point
Normal
Wide
Noise
Reduction
Middle
Low
High
O
Dynamic
Contrast
On / O
HDMI Mode Auto
Video
Graphic
HDR Low
Middle
High
17 2020-11-24 #:180-9152-3 (2020-01-20)
Navigate Enter Exit Return
OK EXIT MENU
Navigating The On Screen Menu
TV/SPK
1 32
4 65
7
•
9
LAST
8
0
OK
MUTE
VOL
MENU
CH
INFO
INPUT
EXIT
Channel
Air / Cable Choose between antenna
and cable
Auto Channel
Scan
Searches for available
channels
Favorite Shows favorite channels
Channel List View tuned in channels
View/Skip Select channels to view
or hide
Channel Number Shows selected channel
Channel Label Assign characters to
selected channel
Setup
Menu
Languages
English
French
Spanish
On-Screen
Display Timeout
5 seconds
15 seconds
30 Seconds
45 seconds
60 Seconds
Input Label TV
AV
Component
Media
HDMI 1
HDMI 2
HDMI 3
Blue Screen On / O
Audio Only On / O
HDMI 4K Standard / Enhancement
Reset Yes / No
peerConnect (CEC)
peerConnect On / O
Device Auto
Power O󰀨
On / O
TV Auto
Power On
On / O
ARC On / O
Voice Guidance
Voice Guidance On / O
Volume Low
Midde
High
Speed Slow
Standard
Fast
Pitch Low
Midde
High
Video
Description
On / O
Lock
System Lock
Enter Password to enter System Lock settings
Defaut Password: 0000
Change
password
Allows the password to be
changed
System Lock On / O
Input Block TV, AV, Component, HDMI
1, HDMI 2, HDMI 3, Media
19 2020-11-24 #:180-9152-3 (2020-01-20)
4
Photos – To view a single photo,
select photo and press play. To view
a slide show, select multiple photos
and press play. Use on screen
menu to control slide show.
Music – To listen to a single song,
select song and press play. To listen
to a playlist, select multiple songs
and press play. Use on screen
menu to control playlist.
Movies – To view a single video,
select video and press play. To view
a playlist, select multiple videos and
press play. Use on screen menu to
control playlist.
Text – To view to a single text le,
select le and press play. To view
a playlist, select multiple les and
press play. Use on screen menu to
control playlist.
Media Functionality
3
PHOTO MUSIC MOVIE TEXT
Return C
Select media type and folder where content is stored.
Navigate Enter Exit Return
OK EXIT MENU
TV/SPK
1 32
4 65
7
•
9
LAST
8
0
OK
MUTE
VOL
MENU
CHINFO
INPUT
EXIT
20 2020-11-24 #:180-9152-3 (2020-01-20)
Compatible Media
Compatible Video
File Format Container Bandwidth
(Mbps)
Frame
Rate
(FPS)
Resolution
AVI MPEG-1 80 30 1920x1088
MPEG-2 MP@HL 80 30 1920x1088
MPEG-4 SP@L0-3,ASP @L0-5 50 30 1920x1088
H.264 100(VCL) 30 3840x2160
MP,HP@Level4.1 120(NAL) - -
H.263 5 30 1280x720
VP6 40 30 1920x1088
MJPEG - 30 1920x1080
MPEG-2 TS
Transport Stream
(.ts)
MPEG-2 MP@HL 80 30 1920x1088
MPEG-4 SP@L0-3,ASP @L0-5 50 30 1920x1088
H.264 MP,HP@Level 4.1 100(VCL)
120(NAL)
30 3840x2160
VC1 (AP) 45 30 1920x1088
H.265 100 30 3840x2160
MPEG File Format
(.mpeg)
MPEG-1 80 30 1920x1088
MPEG-2 MP@HL 80 30 1920x1088
H.264 MP,HP@Level 4.1 100(VCL)
120(NAL)
30 3840x2160
MPEG-4 Part 14
(.mp4)
H.264 MP,HP@Level 4.1 100(VCL)
120(NAL)
30 3840x2160
MPEG-4 SP@L0-3,ASP @L0-5 50 30 1920x1088
H.265 100 30 3840x2160
QuickTime (.mov) H.264 MP,HP@Level 4.1 100(VCL)
120(NAL)
30 3840x2160
MPEG-4 SP@L0-3,ASP @L0-5 50 30 1920x1088
MJPEG - 30 1920x1080
H.265 100 30 3840x2160
Matroska (.mkv) H.264 MP,HP@Level 4.1, 100(VCL)
120(NAL)
30 3840x2160
VP9 - 30 1280x720
H.265 100 30 3840x2160
Flash Video (.v) H.264 MP,HP@Level 4.1 100(VCL)
120(NAL)
30 3840x2160
H.263 5 30 1280x720
Transport Stream
(.ts)
H.264 MP,HP@Level 4.1 100(VCL)
120(NAL)
30 3840x2160
Video Object (.vob) MPEG-2 MP@HL 80 30 1920x1088
DAT (.dat) MPEG-1 80 30 1920x1088
22 2020-11-24 #:180-9152-3 (2020-01-20)
(0):
(1):
(2):
(3):
(4):
(5):
(6):
(7):
(8):
(9):
AV:
CC:
Channel +:
Channel -:
Channel Fav List:
Channel List:
Channel Return:
Component:
Dash:
Down:
EPG:
Exit:
HDMI1:
HDMI2:
HDMI3:
HDMI Toggle:
Info:
Left:
Menu:
MTS:
Mute:
OK:
PMODE:
Power O󰀨:
Power On:
Power On/O󰀨:
Right:
Sleep:
SMODE:
Source:
Surround:
TV:
Up:
USB:
Volume +:
Volume -:
Zoom:
A0, F0, 55, FF, 56, A9
A0, F0, 55, FF, 42, BD
A0, F0, 55, FF, 43, BC
A0, F0, 55, FF, 0F, F0
A0, F0, 55, FF, 1E, E1
A0, F0, 55, FF, 1D, E2
A0, F0, 55, FF, 1C, E3
A0, F0, 55, FF, 18, E7
A0, F0, 55, FF, 45, BA
A0, F0, 55, FF, 4C, B3
A0, F0, 55, FF, ED, 12
A0, F0, 55, FF, 44, BB
A0, F0, 55, FF, 55, AA
A0, F0, 55, FF, 5A, A5
A0, F0, 55, FF, 1A, E5
A0, F0, 55, FF, 59, A6
A0, F0, 55, FF, 15, EA
A0, F0, 55, FF, E7, 18
A0,F0, 55, FF, 2E, D1
A0, F0, 55, FF, 0D, F2
A0, F0, 55, FF, 49, B6
A0, F0, 55, FF, 1B, E4
A0, F0, 55, FF, DE, 21
A0, F0, 55, FF, DF, 20
A0, F0, 55, FF, E0, 1F
A0, F0, 55, FF, EC, 13
A0, F0, 55, FF, 50, AF
A0, F0, 55, FF, 0C, F3
A0, F0, 55, FF, 4E, B1
A0, F0, 55, FF, 11, EE
A0, F0, 55, FF, 14, EB
A0, F0, 55, FF, 02, FD
A0, F0, 55, FF, 4B, B4
A0, F0, 55, FF, AD, 52
A0, F0, 55, FF, AE, 51
A0, F0, 55, FF, 0B, F4
A0, F0, 55, FF, 05, FA
A0, F0, 55, FF, 53, AC
A0, F0, 55, FF, 5B, A4
A0, F0, 55, FF, 01, FE
A0, F0, 55, FF, C7, 38
A0, F0, 55, FF, E8, 17
A0, F0, 55, FF, 17, E8
A0, F0, 55, FF, 57, A8
A0, F0, 55, FF, 0A, F5
A0, F0, 55, FF, 40, BF
A0, F0, 55, FF, 51, AE
COM Settings
Baud Rate 38400
Data Bits 8
Parity None
Stop Bits 1
(RS-232C) Serial Control Of The Display
Attach an RS-232C cable (straight through type) to the supplied D-Sub RS-232C to utilize serial
control function. Control via RS232 should only be utilized by experts familiar with RS232 programing.
23 2020-11-24 #:180-9152-3 (2020-01-20)
Care Of The Screen
Do not rub or strike the screen with anything hard as this may scratch, mark, or even damage the
screen permanently. Ensure that the display is installed in a location where it will be safe from
abrasives and ying debris, which could damage the LCD panel. Never use ammonia or any product
containing ammonia, as it will damage the anti-glare coating on the face of the display. Only use an
approved screen cleaner to clean the display face. Dust the display by wiping the screen and the
cabinet with a soft, clean cloth. If the screen requires additional cleaning, use a clean, damp cloth.
Do not use aerosol cleaners or solvents of any kind. Do not use any chemical such as paint thinner
or benzene to clean the product’s exterior. It may cause scratches on the surface, erasing proper
indications, identication labels, or instructions on the exterior, which may cause misuse and improper
operation of the product.
Mobile Telephone Caution
Keep your mobile telephone away from your display to avoid disturbances in the picture or sound,
possibly causing permanent damage to your display.
End Of Life Directives
In an e󰀨ort to produce environmentally friendly products, your new display contains materials that can
be recycled and reused. At the end of your display's life, specialized companies can minimize display
waste by separating reusable materials from non-reusable materials. Please ensure you dispose of
your display according to local regulations.
MAINTENANCE
Model#: 15420225502, 15420226502, 15420227502
24 2020-11-24 #:180-9152-3 (2020-01-20)
Página en blanco.
ESP
25 2020-11-24 #:180-9152-3 (2020-01-20)
Guía del Usuario
ESP Importado Por: Peerless Industries de Mexico S. DE R.L. DE C.V.
AV. De Las Industrias # 413, Parque Industrial Escobedo,
Escobedo, Nuevo Leon, TEL 01800 849 6577
Hecho En Corea Del Sur
Modelo: 15420225502, 15420226502, 15420227502
Producto: Televisor a color con pantalla de cristal
liquido (LCD)
Marca: Peerless-AV
Caracteristicas Electricas Nominales:
Tension de Alimentación: 100-240 v ca
Naturaleza de Voltaje: Corriente Alterna
Frecuencia: 50/60 hz
Consumo de Corriente: 15420225502 (1.3A),
15420226502 (1.6A), 154202227502 (2.4A)
28 2020-11-24 #:180-9152-3 (2020-01-20)
Lea antes de utilizar el producto
Gracias por comprar nuestro producto. Antes de utilizarlo, lea esta guía del usuario atentamente y
siga las instrucciones para utilizarlo con seguridad. Por favor, guarde esta guía para su referencia e
inclúyala cada vez que cambie o transera el producto a otro lugar.
PRECAUCIONES DE SEGURIDAD GENERAL
En caso de una emergencia, como un incendio o choque eléctrico causado por el producto, llame,
de inmediato, al 9-1-1 o al número apropiado de las agencias de servicios de emergencia de la
policía o los bomberos de su país.
Para minimizar el riesgo de descarga eléctrica o incendio, tenga en cuenta lo siguiente:
• Si el equipo falla o se da algún suceso inusual, como olor a quemado eléctrico, humo o pérdida
de señales de contenido de la pantalla debido al sobrecalentamiento interno, apáguela de
inmediato, desenchufe el cable eléctrico y comuníquese con el fabricante.
• NO desarme, modique ni repare el producto de alguna manera que no se indique en
estas instrucciones. Toda modicación no autorizada hecha al producto anulará la garantía
automáticamente.
• NO toque los cables o los alambres de antenas, los cables eléctricos ni los enchufes cuando
ocurran rayos o truenos ni cuando tenga las manos mojadas.
• No lo sumerja en agua.
• NO lo destruya, procese o coloque cerca de alguna fuente de calor.
• NO lo instale cerca de gases venenosos ni atmósferas con inestabilidad química.
• NO lo instale cerca de campos magnéticos o corrientes eléctricas fuertes.
• NO instale el producto en lugares inestables ni cerca de objetos móviles, equipos que vibren
constantemente o supercies desniveladas. Siga las instrucciones de instalación correctamente
para que pueda utilizar el producto con seguridad, p28-ya que una instalación inadecuada puede
causar que el producto se caiga.
• NO deje ninguna fuente de fuego, como velas, cerca o encima del producto.
• NO opere el producto si se ha caído o si ha recibido algún golpe. Los golpes fuertes pueden
causar que algunos componentes internos se salgan de su lugar y se rompan.
• NO doble ni tuerza los cables eléctricos, los enchufes, los cordones o los alambres con fuerza
excesiva.
• NO bloquee las ranuras de ventilación ni coloque objetos pesados sobre el producto.
• Use voltaje con la potencia eléctrica nominal adecuada. Usar un voltaje que no tenga la potencia
nominal adecuada puede causar un incendio, descarga eléctrica y daños graves al producto.
• NO use tomacorrientes ni extensiones eléctricas múltiples en los que tenga conectados muchos
dispositivos a la vez. Utilice un tomacorriente separado e individual, con potencia nominal y con
un interruptor con falla a tierra para que pueda utilizar el producto con seguridad.
• NO mueva ni transporte el producto con los cables (eléctricos o de conexión de contenido)
conectados a los dispositivos fuente.
• Siempre, conecte el enchufe eléctrico rme y completamente. Al desconectar los cables, siempre,
tire del enchufe, no del cable.
• Siempre, deje el producto apagado al conectar o desconectar los cables eléctricos o de conexión.
• No haga mal uso del enchufe eléctrico polarizado o con descarga a tierra, de manera que no sea
seguro. Un enchufe polarizado tiene dos clavijas, una de las cuales es más ancha que la otra.
Un enchufe con descarga a tierra, tiene dos clavijas y una tercera punta con descarga a tierra. La
clavija ancha y la tercera punta se proporcionan para su seguridad. Si el enchufe proporcionado
no cabe en el receptáculo, consulte a un electricista para remplazar el receptáculo obsoleto.
• Proteja el cable eléctrico de manera que no lo pisen ni lo pinchen, particularmente en los
enchufes, los receptáculos para los aparatos y los sitios por los que salen los cables de los
aparatos.
Para evitar lesiones a las personas, este aparato tiene que tener una conexión a tierra y estar
instalado en una pared de acuerdo con las instrucciones para la instalación.
ADVERTENCIA
29 2020-11-24 #:180-9152-3 (2020-01-20)
ADVERTENCIA
• Nunca aplique presión al exterior de la pantalla LCD. La garantía del fabricante no cubre el mal
uso de parte del usuario ni las instalaciones inadecuadas.
• Si se quiebra el monitor o el cristal, no toque el cristal líquido y manéjelo con cuidado.
• NO se trepe en el producto.
• NO lo instale a una distancia menor de 152cm (5 pies) de un cuerpo de agua.
• NO lo utilice si la temperatura ambiental excede los límites de las temperaturas de
funcionamiento. La temperatura máxima de funcionamiento es de -22°F ~ 122°F (-30°C ~ 50°).
• Este producto está diseñado para el uso en exteriores en áreas con sombra. Coloque el TV
en un área que nunca reciba luz directa del sol, como debajo de un toldo o al lado de una
estructura. Colocar el TV en la luz directa del sol acortará la vida útil de la pantalla y anulará la
garantía.
• NO lo instale en cajas o cavidades empotradas con menos de 5cm (2 pulgadas) para que el aire
uya alrededor de la pantalla. El aire dentro de una pantalla rodeada por todos lados tiene que
estar ventilado.
• El producto debe estar jado a una estructura antes de utilizarlo.
• Se tiene que contar, al menos, con dos personas para cargar y sostener el producto.
• Quítele el polvo al enchufe eléctrico periódicamente para mantenerlo limpio y seco y asegurarse
de que funcione bien y con seguridad.
• Use solamente los jadores o accesorios especicados por el fabricante.
30 2020-11-24 #:180-9152-3 (2020-01-20)
Instalación y requisitos eléctricos del sistema 26 .....................................................................................
Código eléctrico 26 ............................................................................................................................
Fuente eléctrica 26 ...........................................................................................................................
Precaución de la FCC 27 ..................................................................................................................
Declaración de la FCC 27 .........................................................................................................................
Información pertinente 27 .................................................................................................................
Precauciones de seguridad general 28 ....................................................................................................
Instrucciones de conguración .............................................................................................................31
Lista de piezas 31 .............................................................................................................................
Retirar la cubierta del terminal de I/O 32 ...........................................................................................
Conectar los cables 33 ......................................................................................................................
Instalar el repetidor infrarrojo 33 ......................................................................................................
Tecnología freePath 33 ....................................................................................................................
Volver a colocar la cubierta del terminal de I/O 34 ............................................................................
Manejo de cables 35 .........................................................................................................................
Preparar la pantalla para instalación 36 ............................................................................................
Conectar a la fuente eléctrica 37 .......................................................................................................
Instalación y remplazo de las pilas del control remoto 38 .................................................................
Instrucciones de uso.............................................................................................................................39
Encender/Apagar el pantalla 39 ........................................................................................................
Controles integrados 39 ....................................................................................................................
Navegar el menú de la pantalla 40 ..................................................................................................
Imagen .................................................................................................................................40
Sonido ..................................................................................................................................40
Hora .....................................................................................................................................40
Conguración ......................................................................................................................41
Bloqueo ...............................................................................................................................41
Canal ...................................................................................................................................41
Funcionalidad mediática 42 ..............................................................................................................
Fuentes mediáticas compatibles 44 ..................................................................................................
(RS-232C) Control en serie del pantalla 46 .....................................................................................
Mantenimiento .....................................................................................................................................47
Cuidado de la pantalla 47 .................................................................................................................
Precaución sobre teléfonos móviles 47 ............................................................................................
Fin del ciclo de vida útil 47 ..............................................................................................................
Garantía .............................................................................................................................................72
CONTENIDO
31 2020-11-24 #:180-9152-3 (2020-01-20)
Lista de piezas
Descripción Qty
Atelevisor 1
Bcontrol remoto 1
Csujetacables adhesivo 3
Drepetidor infrarrojo 1
Eguía del usuario (no se muestra) 1
Fhoja de apoyo técnico (no se muestra) 1
Gtarjeta de registro de la garantía (no se muestra) 1
A (1)
televisor
B (1)
control remoto
D (1)
repetidor infrarrojo
POWER
TV
TV/SPK
SPK
1 32
4 65
7
•
9
LAST
8
0
OK
AUX1 AUX2
MUTE
VOL
MENU
GUIDE
CH
INFO
INPUT
EXIT
C (3)
sujetacables adhesivo
INSTRUCCIONES DE CONFIGURACIÓN
32 2020-11-24 #:180-9152-3 (2020-01-20)
Retirar la cubierta del terminal de I/O
Retire la cubierta del terminal de I/O y los (8) tornillos para acceder al panel de conexión de las
fuentes.
A
33 2020-11-24 #:180-9152-3 (2020-01-20)
Tecnología freePath
Al utilizar la Tecnología freePath, la cubierta del terminal de I/O permite una mejor recepción de
la señal de WiFi para la conectividad de la red de los dispositivos para televisores inteligentes
guardados dentro del compartimento del terminal de I/O.
Instalar el repetidor infrarrojo (opcional)
D
Conecte el extremo de 3.5 mm del repetidor
infrarrojo de 5V, incluido, en el puerto para
el repetidor infrarrojo del panel de entrada
de la pantalla. Es posible que el puerto para
el repetidor infrarrojo no sea compatible con
repetidores de otros fabricantes.
HDMI 2
HDMI 3
RS232
Repetidor infrarrojo
USB 1 + 2
Antena / cable
HDMI 1
(ARC)
Salida de audio
S/PDIF óptico
Entrada de audio
Entrada de componente
CVBS
Cordons de Connexion
Conecte los dispositivos fuente en la entrada adecuada de la pantalla. Haga todas las conexiones
antes de encender la pantalla.
35 2020-11-24 #:180-9152-3 (2020-01-20)
Fije los cables a la pantalla con los sujetacables adhesivos.
C (3)
C
Manejo de cables.
36 2020-11-24 #:180-9152-3 (2020-01-20)
B
D
Tornillos de montaje
requeridos
(4) tornillos M8
(17.4 mm de largo)
Tamaño A B C D E F
55" 11.81"
(300mm)
7.87"
(200mm)
18.65"
(474mm)
4.61"
(117mm)
1.61"
(41mm)
3.11"
(79mm)
65" 11.81"
(300mm)
7.87"
(200mm)
22.89"
(582mm)
5.42"
(138mm)
1.61"
(41mm)
3.11"
(79mm)
75" 15.75"
(400mm)
7.87"
(200mm)
25.27"
(642mm)
7.45"
(189mm)
2.00"
(51mm)
4.01"
(102mm)
A
F
C E
Preparar la pantalla para instalación
Instale los cables antes de instalar la pantalla. El panel de entradas puede quedar obstruido al
instalar la pantalla.
Para su seguridad, instale solamente un soporte aprobado para uso en exteriores que sea adecuado
para su producto y sostenga el peso de la pantalla. Al instalar una pantalla en exteriores, utilice
soportes ecológicos aprobados adecuados para garantizar la longevidad en entornos hostiles.
Repase la tabla de abajo para determinar las especicaciones de montaje de su pantalla:
VISTA LATERALVISTA TRASERA
37 2020-11-24 #:180-9152-3 (2020-01-20)
Preparar la pantalla para instalación
Tamaño A B C D E
55" 49.09"
(1247mm)
28.54"
(725mm)
47.69"
(1211mm)
26.85"
(682mm)
54.64"
(1388mm)
65" 57.59"
(1463mm)
33.31"
(846mm)
56.24"
(1428mm)
31.62"
(803mm)
64.53"
(1639mm)
75" 66.29"
(1684mm)
38.18"
(970mm)
65.16"
(1655mm)
36.74"
(933mm)
74.52"
(1893mm)
C
A
B D
E
Conectar a la fuente eléctrica
Conecte el cable eléctrico al tomacorriente del interruptor con falla a tierra.
VISTA DELANTERA
38 2020-11-24 #:180-9152-3 (2020-01-20)
Instalación y remplazo de las pilas del control remoto
El uso incorrecto de las pilas puede causar
fugas o derrames. Peerless-AV recomienda
usar las pilas como sigue:
• No combine marcas de pilas.
• No combine pilas nuevas y viejas. Las
pilas podrían agotarse o derramar ácido
más pronto.
• Cambie las pilas agotadas de inmediato
para evitar fugas de ácido en el
compartimiento de las pilas.
• No toque el ácido derramado de las pilas,
ya que puede causarle daño a la piel.
• Quite las pilas si no va a utilizar el control
remoto durante un periodo largo.
• No exponga las pilas a calor excesivo del
sol, de fuego o de otras fuentes de calor,
ya que podrían explotar.
• Apriete los tornillos completamente para
mantener el grado de protección de
ingreso del control remoto.
PRECAUCIÓN
1. Para retirar el módulo de las pilas del control
remoto, quite los dos tornillos del extremo
inferior del módulo de las pilas. Deslice el
módulo de las pilas hacia afuera del control
remoto.
2. Inserte dos pilas nuevas de tamaño AAA en
el módulo de las pilas.
3. Deslice el módulo de las pilas hacia adentro
del control remoto y vuelva a colocar los dos
tornillos en el extremo inferior del módulo de
las pilas.
El control remoto funciona con dos pilas AAA de 1.5V que se instalaron en la fábrica.
Si no se enciende la luz LED roja cuando presione algún botón, es posible que haya que cambiar las
pilas. Siga las instrucciones de abajo para cambiar las pilas.
B
POWER
TV
TV/SPK
SPK
1 32
4 65
7
•
9
LAST
8
0
OK
AUX1 AUX2
MUTE
VOL
MENU
GUIDE
CH
INFO
INPUT
EXIT
POWER
TV
TV/SPK
SPK
1 32
4 65
7
•
9
LAST
8
0
OK
AUX1 AUX2
MUTE
VOL
MENU
GUIDE
CH
INFO
INPUT
EXIT

Specyfikacje produktu

Marka: Peerless-AV
Kategoria: Telewizja
Model: Neptune

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Peerless-AV Neptune, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Telewizja Peerless-AV

Peerless-AV

Peerless-AV XHB554 Instrukcja

21 Grudnia 2024
Peerless-AV

Peerless-AV Neptune NT654 Instrukcja

4 Października 2024
Peerless-AV

Peerless-AV Neptune NT554 Instrukcja

4 Października 2024
Peerless-AV

Peerless-AV UltraView UV552 Instrukcja

2 Października 2024
Peerless-AV

Peerless-AV UltraView UV652 Instrukcja

2 Października 2024
Peerless-AV

Peerless-AV UltraView UV492 Instrukcja

2 Października 2024
Peerless-AV

Peerless-AV UltraView UV551 Instrukcja

2 Października 2024
Peerless-AV

Peerless-AV NT753 Instrukcja

2 Września 2024
Peerless-AV

Peerless-AV NT553 Instrukcja

30 Sierpnia 2024
Peerless-AV

Peerless-AV Neptune Instrukcja

30 Sierpnia 2024

Instrukcje Telewizja

Najnowsze instrukcje dla Telewizja

Daewoo

Daewoo 14C7GT Instrukcja

9 Kwietnia 2025
Philips

Philips 14pt2694 Instrukcja

9 Kwietnia 2025
Panasonic

Panasonic Viera TX-L32D28 Instrukcja

9 Kwietnia 2025
Panasonic

Panasonic TX-L24C5B Instrukcja

9 Kwietnia 2025
Panasonic

Panasonic TX-24E302B Instrukcja

9 Kwietnia 2025
Panasonic

Panasonic TX-26LX62FA Instrukcja

9 Kwietnia 2025
Panasonic

Panasonic TX-24CS500B Instrukcja

9 Kwietnia 2025
TCL

TCL 65P69K Instrukcja

9 Kwietnia 2025
TCL

TCL 55P69K Instrukcja

9 Kwietnia 2025
TCL

TCL 50P69K Instrukcja

9 Kwietnia 2025