Instrukcja obsługi PCE Instruments PCE-VS10

PCE Instruments Sprzęt pomiarowy PCE-VS10

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla PCE Instruments PCE-VS10 (5 stron) w kategorii Sprzęt pomiarowy. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/5
Manual
Vibration Meter Sensor Switch
PCE-VS 10
PCE Americas Inc.
711 Commerce Way
Suite 8
Jupiter
FL-33458
USA
From outside US: +1
Tel: (561) 320-9162
Fax: (561) 320-9176
info@pce-americas.com
www.pce-instruments.com/english
www.pce-instruments.com
PCE Instruments UK Ltd.
Units 12/13
Southpoint Business Park
Ensign way
Hampshire / Southampton
United Kingdom, SO31 4RF
From outside UK: +44
Tel: (0) 2380 98703 0
Fax: (0) 2380 98703 9
info@industrial-needs.com
Instruction Manual
Vibration Switch VS103&(฀
Application and Operation
The instrument enables simple and cost efficient monitoring of vibration on rotating machines, for example,
in the frame of preventative maintenance to DIN/ISO 10816. Likewise, it can be used as a limit switch for a
diverse range of processes involving vibration and shock. Thanks to its inbuilt piezoelectric accelerometer
and signal processing, by means of a micro controller, the vibration switch operates reliably and with high
reproducibility.
Selectable filters and integrators, variable alarm settings and the high level of protection IP67 make VS103&(฀
ideal for a variety of applications, for example:
·Monitoring compressors, pumps, fans, generators
·Rail vehicles
·Quality control
·Transporting fragile goods
·Surveillance of doors and gates
·Impact and drop testing
By means of the inbuilt piezoelectric accelerometer, VS10 monitors vibrations perpendicular to the lid of its3&(฀
casing. It measures both positive and negative excitation.
3&(฀VS10 has a digital signal processor and a relay output for signalization. It indicates alarm status via green
and red LED's.
Parametrization
The parametrization is carried out with PC software via a common micro
USB cable. To connect the USB cable, unscrew the four socket head screws
and remove the lid. Inside you will see the USB connector (Figure 1).
Caution: If a USB cable is connected, the power will be supplied by the PC.
Make sure the power is never supplied via a USB cable and the connection
terminals simultaneously.
When connecting VS10 to a PC for the first time, you will be prompted 3&(฀
install the driver. The driver file “MMF_VCP.zip” can be found on our
website:
Unzip and save both the enclosed files to a directory on the computer.
When Windows requests the location of the instrument driver, enter this di-
rectory. The instrument driver is signed and runs with Windows XP, Vista, 7, 8 and 10.
The driver installs a virtual COM Port on the PC and operates in CDC mode, thus enabling simple control
via the ASCII commands.
To setup the VS10 the PC-Software is available under the above link. Unzip the file vs1x.zip into a di-3&(฀ VS1x
rectory on your PC and then start . The installation directories can be changed if needed. The pro-setup.exe
gram is a LabView application and for this reason installs several components of the LabView Run-Time en -
vironment from National Instruments.
Once installed, the program is located under in the start menu of your computer. (Figure 2).Metra Radebeul
Figure 1: Connections
To establish a connection to VS10, press . The program searches COM-Ports 1 to 50 for the in-3&(฀ Search VS1x
strument. As soon as it has been found the status report appears and the instrument settingsVS1x connected
are read.
In the row next to the COM port number you will find the non-editable data, model, version, serial number
and date of calibration. You can enter the device name yourself.
When entering the gain, this refers to the analogue pre-amplification before the analogue-to-digital converter
stage. The gain levels 1, 10 and 100-fold are available for selection as well as automatic gain switching. In
many cases automatic gain setting is most appropriate. It can, however, occasionally be disadvantageous if
single shock pulses are measured. If previously only low amplitudes had been recorded, it may occur that
short single impulses fail to trigger the alarm signal immediately, due to the switching of the gain. In such
cases a fixed gain should be set according to the maximum expected amplitude ( ). fix
Under there is a row of high and low pass filter combinations to choose from. DependingFilter / Integrator
on the area of application, you can monitor either acceleration without integration ( .) or the single inte-accel
grated signal of velocity ( .). For vibrations below 1 kHz, for which the resulting energy is of relevance,veloc
it is recommendable to monitor velocity, whereas for measurements involving higher frequencies and im -
pacts, acceleration is usually preferred.
Under Warning/Alarm RMS you can find the limit value settings. Here your can select whether values or
Peak values are to be monitored. Monitoring peak values can be advantageous for recording single events,
while RMS is relevant for trend monitoring, for example, in the field of machine condition monitoring. The
Alarm limit is entered in the unit of measurement (m/s² or mm/s). The instrument can give a warning signal
before it reaches the alarm limit. The warning threshold is entered as a percentage of the alarm limit.
Figure 2: Parameter Program

Specyfikacje produktu

Marka: PCE Instruments
Kategoria: Sprzęt pomiarowy
Model: PCE-VS10

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z PCE Instruments PCE-VS10, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Sprzęt pomiarowy PCE Instruments

PCE Instruments

PCE Instruments PCE-DD-A Instrukcja

28 Marca 2025
PCE Instruments

PCE Instruments PCE-128 Instrukcja

28 Marca 2025
PCE Instruments

PCE Instruments PCE-3000UL Instrukcja

28 Marca 2025
PCE Instruments

PCE Instruments PCE-BPD-C-66A Instrukcja

28 Marca 2025
PCE Instruments

PCE Instruments PCE-DFG N 5TW Instrukcja

28 Marca 2025
PCE Instruments

PCE Instruments PCE-MA 100 Instrukcja

28 Marca 2025
PCE Instruments

PCE Instruments PCE-MA 110 Instrukcja

28 Marca 2025
PCE Instruments

PCE Instruments PCE-DFG NF 5K Instrukcja

28 Marca 2025
PCE Instruments

PCE Instruments PCE-LES 103UV Instrukcja

28 Marca 2025
PCE Instruments

PCE Instruments PCE-HVAC 10 Instrukcja

28 Marca 2025

Instrukcje Sprzęt pomiarowy

Najnowsze instrukcje dla Sprzęt pomiarowy

Topex

Topex 31C800 Instrukcja

28 Marca 2025
Grundfos

Grundfos Hydro Solo-E Instrukcja

28 Marca 2025
Victron Energy

Victron Energy Smart Battery Sense Instrukcja

27 Marca 2025
Einhell

Einhell NWL 90 Instrukcja

27 Marca 2025
Einhell

Einhell NLW 180 Instrukcja

27 Marca 2025
Einhell

Einhell NDM 15 Instrukcja

27 Marca 2025
Einhell

Einhell NKL 90/4 Instrukcja

27 Marca 2025
NEO Tools

NEO Tools 94-006 Instrukcja

27 Marca 2025
Kern

Kern KFP 6000V20M Instrukcja

26 Marca 2025
Kern

Kern KFP 1500V40M Instrukcja

26 Marca 2025