Instrukcja obsługi PCE Instruments PCE-TC 32N

PCE Instruments Sprzęt pomiarowy PCE-TC 32N

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla PCE Instruments PCE-TC 32N (32 stron) w kategorii Sprzęt pomiarowy. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/32

User manuals in various languages (français, italiano, español, português, nederlands,

türk, polski) can be found via our product search on:

www.pce-instruments.com

PCE-TC 32N

ENGLISH

THERMAL IMAGER

USER MANUAL

3 4

1.1 1.2

1. Interface and Cover

1-1. TypeC USB/Charge

1-2. Micro SD card slot

2. LCD Display

3. Menu/OK Button

4. Power/lock Button

5. Up/down/Right /Left Button

6. FlashLight

7. Laser Pointer

8. Infrared Camera Lens

9. Visual Camera

10. Trigger

11. Battery

The Thermal Imager is handheld imaging camera used for predictive maintenance, equipment trouble-

shooting, and verication. Focus the len to the object, Then the thermal and visual images are displayed

on the LCD and can be saved to a Micro SD Memory card. Transferring images to a PC is accomplished by

removing the SD memory card and connecting it to a PC through the included card reader, or transfer the

images and video stream to the smart device with “Thermoview” apps installed.

In addition to the features mentioned above, the Thermal Imager provide video recording and play back.

1. INTRODUCTION

2. STRUCTURE DESCRIPTION

»To prevent eye damage and personal injury, do not look into the laser. Do not point laser directly at

persons or animals or indirectly o reective surfaces.

»Do not disassemble or do a modication to the Thermal Imager.

»Do not point the Thermal Imager (with or without the lens cover) at intensive energy sources, for

example devices that emit laser radiation, or the sun.

»This can have an unwanted eect on the accuracy of the camera. It can also cause damage to the

detector in the Thermal Imager.

»Do not use the Thermal Imager in a temperature higher than +50°C (+122°F), lower than -20°C (-4°F).

High temperature or low temperature can cause damage to the Thermal Imager.

»Only use the correct equipment to discharge the battery.

If you do not use the correct equipment, you can decrease the performance or the life cycle of the

battery. If you do not use the correct equipment, an incorrect ow of current to the battery can occur.

This can cause the battery to become hot, or cause an explosion and injury to persons.

»Do not pull out the battery when the thermal imager is working.

If you pull out the battery when the thermal imager is working, it may cause the thermal imager work

unnormal.

»Do not disassemble or do a modication to the battery.

The battery contains safety and protection devices which, if they become damaged, can cause the

battery to become hot, or cause an explosion or an ignition. If there is a leak from the battery and the

uid gets into your eyes, do not rub your eyes. Flush well with water and immediately get medical care.

»Do not make holes in the battery with objects. Do not hit the battery with a hammer. Do not step on the

battery, or apply strong impacts or shocks to it.

»Do not put the battery in or near a re, or in direct sunlight, or other high-temperature locations. Do not

solder directly onto the battery.

»Always charge the battery in the special temperature rang.

»The temperature range through which you can charge the battery is 0°C to +50°C(+32°F to +122°F). If

you charge the battery at temperatures out of this range, it can cause the battery to become hot or to

break. It can also decrease the performance or the life cycle of the battery.

»Do not get water or salt water on the battery, or permit the battery to get wet.

»Clean the case with a damp cloth and a weak soap solution. Do not use abrasives, isopropyl alcohol, or

solvents to clean the case or lens/screen.

»Be careful when you clean the infrared lens. Do not clean the infrared lens too vigorously. This can

damage the antireective coating.

»Avoid condensation

Take the Thermal Imager from from cold to hot, it will appear condensation in thermal Imager. To

protect the Thermal Imager, you should power of the Thermal Imager, wait until the Thermal Imager has

become war enough for the condensation to evaporate.

»Storage

If you do not use the Thermal Imager, put the Thermal Imager in cool and dry environment, if you store

Thermal Imager equipped with the battery, the power of the battery will be exhausted.

3. SAFETY INFORMATION

Specyfikacje produktu

Marka:	PCE Instruments
Kategoria:	Sprzęt pomiarowy
Model:	PCE-TC 32N

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z PCE Instruments PCE-TC 32N, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Sprzęt pomiarowy PCE Instruments

PCE Instruments PCE-PMI 1 Instrukcja

14 Stycznia 2025

PCE Instruments PCE-324 Instrukcja

14 Stycznia 2025

PCE Instruments PCE-TC 32N Instrukcja

14 Stycznia 2025

PCE Instruments PCE-ACO 9500 Instrukcja

14 Stycznia 2025

PCE Instruments PCE-313A Instrukcja

10 Stycznia 2025

PCE Instruments PCE-320 Instrukcja

10 Stycznia 2025

PCE Instruments PCE-032-LED Instrukcja

10 Stycznia 2025

PCE Instruments FME Instrukcja

10 Stycznia 2025

PCE Instruments PCE-2500N Instrukcja

10 Stycznia 2025

PCE Instruments PCE-2550 Instrukcja

10 Stycznia 2025

Instrukcje Sprzęt pomiarowy

Najnowsze instrukcje dla Sprzęt pomiarowy

Klein Tools CL810 Instrukcja

14 Stycznia 2025

Klein Tools CL710 Instrukcja

14 Stycznia 2025

Ebro PHT 830 Instrukcja

13 Stycznia 2025

Kern FL 1KG Instrukcja

10 Stycznia 2025

PeakTech 6193 Instrukcja

10 Stycznia 2025

Gossen Metrawatt PROFiTEST H+E EASY CHECK Instrukcja

10 Stycznia 2025

CSL 306637 Instrukcja

9 Stycznia 2025

TFA 40.1058.11 Instrukcja

9 Stycznia 2025

TFA SANDY 40.1043.06 Instrukcja

9 Stycznia 2025

TFA 40.1046 Instrukcja

9 Stycznia 2025