Instrukcja obsługi PCE Instruments PCE-DDMU 10

PCE Instruments Sprzęt pomiarowy PCE-DDMU 10

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla PCE Instruments PCE-DDMU 10 (4 stron) w kategorii Sprzęt pomiarowy. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/4

PCE Americas Inc.

711 Commerce Way

Suite 8

Jupiter

FL-33458

USA

From outside US: +1

Tel: (561) 320-9162

Fax: (561) 320-9176

info@pce-americas.com

www.pce-instruments.com/english

www.pce-instruments.com

PCE Instruments UK Ltd.

Unit 1 1

Southpoint Business Park

Ensign way

Hampshire / Southampton

United Kingdom, SO31 4RF

From outside UK: +44

Tel: (0) 2380 98703 0

Fax: (0) 2380 98703 9

info@industrial-needs.com

Differential Pressure Transmitter

PCE-DDMU 10

INSTRUCTION MANUAL

Table f ontents o c

1 General nformation. i

2 Product dentification. i

3 Installation.

4.Initial tart s -up

5 Operation.

6 Dimensions Fixing. /

7 Maintenance.

8 Return.

9 Warranty conditions.

Operating Manual

Dierential Pressure Transmitter PCE-DDMU 10

Menu button

1 General information

Do not blow into the pressure ports!

This causes damage to the device.

- This operating manual contains important informa-

tion on proper usage of the device. Read thisthe

operating manual carefully before installing and

starting up the pressure measuring device.

- c-Adhere to the safety notes and operating instru

tions which are given in the operating manual. Addi-

tionally applicable regulations regarding occupa-

tional safety, accident prevention as well as national

installation standards and engineering rules must

be complied with!

- This operating manual is part of the device. It must

be kept near its location and always be accessible

to all employees.

- This operating manual is copyrighted. The contents

of this operating manual reflect the version available

at the time of printing.

WARNING! To avoid operator hazards and dam-

age to he device, the following instructions t may

only be carried out by qualified technical perso n-

nel.

Limitation of liability: In -case of non

observance of the operating manual, inappropri-

ate use, modifications or damage, no liability is

assumed and warranty claims will be excluded.

Symbols used:

: Warning

!: Caution

: Note

– T –echnical modifications reserved

2 Product identification

2.1 Intended use

T differential pressurhe PCE-DDMU 10 e

transmitter has developed for t been he

measurement of pressur difference dry, non e of -

aggressiv gases pressuriz aire and ed and an bec

us for wide r of different HVACed a ange

applications.

Its robust desi means it c us i the gn an be ed n

laboratory under industrial conditions. and

Preferred e e n areas of us ar i heating, ventilation

and ng ean air conditioni systems; cl room and

medical technology, filter technology draft and

meteri checksng .

It s he operator's responsibility to check and verify i t

the suitability f he device or intended o t f the applica-

tion. f any bts emain, ease contact our les I dou r pl sa

department n order o ensure proper se. i t u

PCE Instruments is not liable for any incorrect

selections and heir t effects!

WARNING! – Danger by inappropriate use!

2.2 Identification

- The device can be identified by its manufacturing

label. It provides the most important data. T he

product can be clearly identified by the ordering

code.

Fig. 1: Manufacturing label

!The manufacturing label may not be removed

from the device!

2 .3 Package contents

Please verify that all listed parts are included in the

delivery undamaged and comply with your order :

1 Differential ressure Transmitter P PCE-DDMU 10

1 Operating manual

2.4 Transport and storage

Permissible temperature for storage: 10 °C to + 70 °C-

For transport make sure that both pressure inputs of

differential pressure sensors are open. The air transport

of absolute pressure sensors should only be done in a

pressure compensated cabin.

2.5 Declaration of onformity c / CE

The delivered evice all egal equirements. d fulfills l r

T applicablehe directives, harmonised standards d an

documents are listed in the EC eclaration of onformity d c .

The operational safety is additionally confirm by the ed

CE si on he manufacturing label. gn t

3 Installation

3.1 Mounting nd afety a s instructions

WARNING! This device may only be installed by

qualified technical personnel who have read and

understood the operating manual!

WARNING! Install the device only when depres-

surized and current free- !

!Handle this device with care, both in ed and packag

unpackaged condition!

!No modifications/changes should be made on the

device.

!Do not throw the device!

!Do not use any force when installing the device, to

prevent damage of the device and the plant!

!Avoid of sources interference (transformers,

transmitters, motors etc.) or sources of heat in the

surrounding area .

!Shocks or vibrations at the mounting connection

can cause distortions to the output signals.

3.2 Installation steps

- Carefully remove the pressure measuring device

from its package and dispose of the package prop-

erly.

- Mount the device in a suitable location using both

straps. The corresponding dimensions are provided

under "6".

- Connections should be vertical, i. e. the pressure

connections should point downwards. The sensors

are calibrated in the factory for these mounting con-

ditions. In addition, the formation of condensation in

the pressure tubing of the sensor is also reduced.

- Use the appropriate hoses for the connection.

Fig. 2: PCE-DDMU 10

3.3 installation Electrical

WARNING! This device may only be installed by

qualified technical personnel who have read and

understood the operating manual!

- Open the top cover and establish the electrical

connection of the device according to the follow-

ing description. Screw the top cover onto the box

again.

- Guide externally the power supply line through

the right so that the wires can cable fitting be

connected with the right terminal block (SUP-

PLY) without any problem.

- Next, tighten the cable gland by hand. Make

sure, however, that the cable is strain-relieved.

3.4 Pressure port

- Connect the hose with the higher pressure to the

right hand (positive) pressure port.

- Connect the hose with the lower pressure to the

left hand (negative) pressure port.

4 - Initial start up

After switching on the power supply, the output

signal can be measured. Variations in the output

signals may have two possible causes:

1. The warm up time of the sensor is about 30min- .

After this period, the sensor signal should be

stable for zero differential pressure and constant

ambient temperature.

2. For small pressure ranges, a slight deviation in

the zero point due to ambient conditions can oc-

cur. This error can be corrected by adjusting the

zero-point potentiometer of the sensor after the

warm- up time. (Set the output signal of the sen-

sor with both pressure inputs open to the nomi-

nal value.)

5 Operation

5 .1 General information

WARNING! - check Before start up, the user must

to ensure proper installation and for any visible de-

fects.

WARNING! The device may only be started and

operated by authorized personnel who have read

and understood the operating manual!

WARNING! The device may only be used within

the technical specifications the data in the (see

data sheet)!

WARNING! – Do not touch the bonding wires this

ca . n destroy the device

5.2 Setting of damping

P otentiometer for setting the damping is located

adjacent to the display on the left (see image 2).

The damping of the device can be set by turning a

size 2 Phillips screwdriver in the area of 0 to

5000ms.

5.3 Menu buttons

Zeroing: secondpush left menu button for at least 1

5.4 Configuration switch

3- - :wire system

1 2 3 4

Off / 0 ... 10 V 0 ... 20 mA

On 5 V0 ... / 4 ... 20 mA

Off Automatic zero adjustment

off

On Zero adjustment active at

start and for 24h

Nominal pressure range

Off Off 4 1,6 10 40 250 1000

Customized ranges

6 On Off 1,0 2,5 25 60 400

Off On 160 600

2- -wire system:

1 2 3 4

Off Off Automatic zero adjustment

off

On O ff Zero adjustment active at

start

O ff On Zero adjustment active at

start and for 24h

On On Zero adjustment active at

start, then every 7 days

Nominal pressure range

Off Off 4 1,6 10 40 250 1000

Customized ranges

On Off 6 1,0 2,5 25 60 400

Off On 160 600

The switches 1 and 2 don't have any function

at special pressure ranges.

terminal block

2- -wire system

Ordering code

Connector pinout

Type designation

Supply

Nominal

pressure

range

Sig nal

Serial

number

Display

(optional)

Potentiometer for adjust-

ing damping

P - hillips screwdriver

size 2

Configuration

switching

Negative

pressure connection

Positive

pressure connection

Cable gland M16x1.5

terminal block

3 wire system

3- -s 3- -wire ystem )(current / voltage wire system ( )current / voltage

w ith two outputs

supply terminal-: 7 - : VS

supply +: terminal 8: VS+

signal: 9 terminal : IOUT

signal: terminal 10: VOUT

Output 2 NO2: terminal 1 : NO2

Output 2 C2: terminal 2 : C2

Output 2 NC2 terminal 3 : NC2

Output 1 NO1 terminal 4 : NO1

Output 1 C1 terminal 5 : C1

Output 1 NC1 terminal 6 : NC1

supply -: terminal 7: VS-

supply +: terminal 8: VS+

signal: terminal 9 : IOUT

signal: terminal 10: VOUT

2- -s 2- - wire ystem (current) wire system (current) with two outputs

supply +: terminal 1: VS+

supply terminal-: 2 - : VS

supply +: terminal 1 + : VS

supply terminal-: 2 - : VS

output 1: terminal 3: S1

output 2: terminal 4: S2

Specyfikacje produktu

Marka:	PCE Instruments
Kategoria:	Sprzęt pomiarowy
Model:	PCE-DDMU 10

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z PCE Instruments PCE-DDMU 10, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Sprzęt pomiarowy PCE Instruments

PCE Instruments PCE-DD-A Instrukcja

28 Marca 2025

PCE Instruments PCE-128 Instrukcja

28 Marca 2025

PCE Instruments PCE-3000UL Instrukcja

28 Marca 2025

PCE Instruments PCE-BPD-C-66A Instrukcja

28 Marca 2025

PCE Instruments PCE-DFG N 5TW Instrukcja

28 Marca 2025

PCE Instruments PCE-MA 100 Instrukcja

28 Marca 2025

PCE Instruments PCE-MA 110 Instrukcja

28 Marca 2025

PCE Instruments PCE-DFG NF 5K Instrukcja

28 Marca 2025

PCE Instruments PCE-LES 103UV Instrukcja

28 Marca 2025

PCE Instruments PCE-HVAC 10 Instrukcja

28 Marca 2025

Instrukcje Sprzęt pomiarowy

Najnowsze instrukcje dla Sprzęt pomiarowy

Topex 31C800 Instrukcja

28 Marca 2025

Grundfos Hydro Solo-E Instrukcja

28 Marca 2025

Victron Energy Smart Battery Sense Instrukcja

27 Marca 2025

Einhell NWL 90 Instrukcja

27 Marca 2025

Einhell NLW 180 Instrukcja

27 Marca 2025

Einhell NDM 15 Instrukcja

27 Marca 2025

Einhell NKL 90/4 Instrukcja

27 Marca 2025

NEO Tools 94-006 Instrukcja

27 Marca 2025

Kern KFP 6000V20M Instrukcja

26 Marca 2025

Kern KFP 1500V40M Instrukcja

26 Marca 2025